AR-B1042
PC/104 VGA/LCD
DISPLAY MODULE
User’ s Guide
Edition: 1.42
Book Number: AR-B1042-99.B02
AR-B1042 User’s Guide
Table of Contents
0. PREFACE...............................................................................................................................................................0-2
0.1 COPYRIGHT NOTICE AND DISCLAIMER............................................................................................................................ 0-2
0.2 WELCOME TO THE AR-B1042 DISPLAY MODULE ............................................................................................................ 0-2
0.3 BEFORE YOU USE THIS GUIDE.......................................................................................................................................... 0-2
0.4 RETURNING YOUR BOARD FOR SERVICE ....................................................................................................................... 0-2
0.5 TECHNICAL SUPPORT AND USER COMMENTS............................................................................................................... 0-2
0.6 ORGANIZATION.................................................................................................................................................................... 0-3
0.7 STATIC ELECTRICITY PRECAUTIONS ............................................................................................................................... 0-3
1. OVERVIEW.............................................................................................................................................................1-1
1.1 INTRODUCTION.................................................................................................................................................................... 1-1
1.2 PACKING LIST....................................................................................................................................................................... 1-2
1.3 AR-B1042 AND ACCESSORY LIST...................................................................................................................................... 1-3
1.4 FEATURES ............................................................................................................................................................................ 1-3
2. SETTING UP THE SYSTEM...................................................................................................................................2-1
2.1 OVERVIEW............................................................................................................................................................................ 2-1
2.2 SYSTEM SETTING................................................................................................................................................................ 2-2
2.2.1 Universal Panel Control (CON1).................................................................................................................................... 2-3
2.2.2 VGA Monitor Connector (CON2).................................................................................................................................... 2-3
2.2.3 Panel Power Connector (CON3).................................................................................................................................... 2-3
2.2.4 PC/104 Connector.......................................................................................................................................................... 2-4
2.2.5 Setting Linear Address (J1 & J2) ................................................................................................................................... 2-6
2.2.6 Setting Clock Source (J3) .............................................................................................................................................. 2-6
2.2.7 DE/E Signal from M or LP (J4)....................................................................................................................................... 2-6
2.2.8 Setting BIOS Bank (J5).................................................................................................................................................. 2-7
3. CRT/LCD FLAT PANEL DISPLAY ........................................................................................................................3-1
3.1 BOARD INSTALLATION........................................................................................................................................................ 3-1
3.2 CONNECTING THE CRT MONITOR..................................................................................................................................... 3-1
3.3 LCD FLAT PANEL DISPLAY ................................................................................................................................................. 3-2
3.4 INVERTER BOARD DESCRIPTION...................................................................................................................................... 3-3
4. INSTALLATION OF THE UTILITY SOFTWARE....................................................................................................4-1
4.1 INSTALL APPLICATION SOFTWARE................................................................................................................................... 4-1
4.1.1 Windows 3.1................................................................................................................................................................... 4-1
4.1.2 Panning Drivers.............................................................................................................................................................. 4-2
4.1.3 AutoCAD R12................................................................................................................................................................. 4-3
4.1.4 Lotus 1-2-3 Lotus Symphony ......................................................................................................................................... 4-4
4.1.5 Word............................................................................................................................................................................... 4-5
4.1.6 WordPerfect ................................................................................................................................................................... 4-5
4.1.7 Windows NT................................................................................................................................................................... 4-6
4.2 THE CHIPSDSP UTILITY PROGRAM................................................................................................................................... 4-6
4.2.1 Installing the Utility ......................................................................................................................................................... 4-6
4.2.2 How to Use the Utility..................................................................................................................................................... 4-6
4.3 THE CHIPSCPL UTILITY PROGRAM ................................................................................................................................... 4-7
4.3.1 Installing the Utility ......................................................................................................................................................... 4-7
4.3.2 How to Use the Utility..................................................................................................................................................... 4-7
4.4 THE SETCOL UTILITY PROGRAM....................................................................................................................................... 4-8
4.4.1 Installing the Utility ......................................................................................................................................................... 4-8
4.4.2 How to Use the Utility..................................................................................................................................................... 4-9
5. ERROR (BEEP) CODES & INDEX.........................................................................................................................5-1
5.1 ERROR (BEEF) CODES........................................................................................................................................................ 5-1
5.2 INDEX .................................................................................................................................................................................... 5-1
0-1
AR-B1042 User’s Guide
0.PREFACE
0.1 COPYRIGHT NOTICE AND DISCLAIMER
January 1999
Acrosser Technology makes no representations or warranties with respect to the contents hereof and specifica lly
disclaims any implied warranties of merchantability or fitness for any particular purpose. Furthermore, Acrosser
Technology reserves the right to revise this publication and to make changes from time to time in the contents
hereof without obligation of Acrosser Technology to notify any person of such revisions or changes.
Possession, use, or copying of the software described in this publication is authorized only pursuant to a valid
written license from Acrosser or an authorized sublicensor.
(C) Copyright 錯誤! 尚未定義書籤。 Acrosser Technology Co., Ltd., 1999. All rights Reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval s ystem, or translated
into any language or computer language, in any form or any me ans, electronic, mechanical, magnetic, optical,
chemical, manual or otherwise, without the prior written consent of Acrosser Technology.
Acrosser, IBM, NEC, C & T, Windows 3.1, MS-DOS, AutoCAD, Lotus 1-2-3, WordPerfect, WINNT, HITACHI,
ORIO N , S H A R P …a r e registered trademarks.
All other trademarks and registered trademarks are the property of their respective holders.
This document was produced with Adobe Acrobat 3.01.
0.2 WELCOME TO THE AR-B1042 DISPLAY MODULE
This guide introduces the Acrosser AR-B1042 display module.
Use the information describes this card’s functions, features, and how to start, set up and operate your A R-B1042.
You also could find general system information here.
0.3 BEFORE YOU USE THIS GUIDE
Check the packing list, make sure the accessories in the package.
AR-B1042 diskette provides the newest information about the card. Please refer to the README.DOC file of
the enclosed utility diskette. It contains the modification and hardware & software information, and adding the
description or modification of product function after manual published.
0.4 RETURNING YOUR BOARD FOR SERVICE
If your board requires servicing, contact the dealer from whom you purchased the product for service information.
If you need to ship your board to us for service, be sure it is packed in a protective carton. We recommend that
you keep the original shipping container for this purpose.
You can help assure efficient servicing of your product by following these guidelines:
1. Include your name, address, telephone and facsimile number where you may be reached during the day.
2. A description of the system configuration and/or software at the time is malfunction.
3. A brief description is in the symptoms.
0.5 TECHNICAL SUPPORT AND USER COMMENTS
User’s錯誤! 尚未定義書籤。 comments are always welcome as they assist us in improving the usefulness of our
products and the understanding of our publications. They form a ver y important part of the input used for product
enhancement and revision.
We may use and distribute any of the information you supply in any way we believe appropriate without incurring
any obligation. You may, of course, continue to use the information you supply.
If you have suggestions for improving particular sections or if you find any errors, please indicate the manual title
and book number.
Please send your comments to Acrosser Technology Co., Ltd. or your local sales representative.
Internet electronic mail to: webmaster@acrosser.com
0-2
AR-B1042 User’s Guide
0.6 ORGANIZATION
This information for users covers the following topics (see the Table of Contents for a detailed listing):
z Chapter 1, “Overview”, provides an overview of the system features and packing list.
z Chapter 2, “Setting Up the System”, describes how to adjust the jumper, and the connectors setting.
z Chapter 3, “CRT/LCD Flat Panel Display”, describes the configuration and installation procedure using
LCD display.
z Chapter 4, “Installation of the Utility Software”, describes setup procedures including information on th e
utility diskette.
z Chapter 5, Error (Beep) C ode & Index
0.7 STATIC ELECTRICITY PRECAUTIONS
Before removing the board from its anti-static bag, read this section about static electricity precautions.
Static electricity is a constant danger to computer systems. The charge that can build up in your body may be
more than sufficient to damage integrated circuits on any PC board. It is, therefore, important to observe basic
precautions whenever you use or handle co mputer components. Although areas with humid climates are much
less prone to static build-up, it is always best to safeguard against accidents may result in expensive repairs. The
following measures should generally be sufficient to protect your equipment from static discharge:
• Touch a grounded metal object to discharge the static electricit y in your body (or ideally, wear a grounded
wrist strap).
• When unpacking and handling the board or other system component, place all materials on an antic static
surface.
• Be careful not to touch the components on the board, especially the “golden finger” connectors on the bottom
of every board.
0-3
AR-B1042 User’s Guide
1. OVERVIEW
This chapter provides an overview of your system features and capabilities. The following topics are covered:
z Introduction
z Packing List
z AR-B1042 and Accessory List
z Features
1.1 INTRODUCTION
The AR-B1042 is a PC/104 form factor super VGA controller for CRT and LCD display. It supports CRT color
monitor, STN, Dual-Scan, TFT, monochrome and color panels. It can be connected to create a compact video
solution for the industrial environment. 1MB of RAM on-boarded allows a maximum CRT resolution of 1280X102 4
and a LCD resolution of 640X480 with 64K colors.
For different VGA display modes, your monitor must possess certain characteristics for display the mode you want.
There is the table to list the standard VGA display modes for the module and monitor information which supports
them.
Model#
(Hex)
0+, 1+ 16 40x25 9x16 360x400 Text 50/28.322 31.5 70
0+, 1+ 16 40x25 8x14 320x350 Text 56/25.175 31.5 70
0+, 1+ 16 40x25 8x8 320x200 Text 56/25.175 31.5 70
2+, 3+ 16 80x25 9x16 720x400 Text 56/28.322 31.5 70
2+, 3+ 16 80x25 8x14 640x350 Text 56/25.175 31.5 70
2+, 3+ 16 80x25 8x8 640x200 Text 56/25.175 31.5 70
Table 1-1 Supported Video Modes – VGA Standard
Color Text
Display
4 4 40x25 8x8 320x200 Graphics 56/25.175 31.5 70
5 4 40x25 8x8 320x350 Graphics 56/25.175 31.5 70
6 2 80x25 8x8 640x200 Graphics 56/25.175 31.5 70
7+ Mono 80x25 9x16 720x400 Text 56/25.322 31.5 70
7+ Mono 80x25 9x14 720x350 Text 56/25.322 31.5 70
7+ Mono 80x25 9x8 720x350 Text 56/25.322 31.5 70
13 256 40x25 8x8 320x200 Graphics 56/25.175 31.5 70
Font
Size
Pixel
Resolution
Display
Mode
Dot Clock
(MHz)
Horizontal
Freq. (KHz)
Vertical
Freq. (Hz)
1-1
AR-B1042 User’s Guide
Model#
(Hex)
71,75I 65/44.900 35.5 43
Table 1-2 Supported Video Modes – Extended Resolution
NOTE: 1. 8 bit Linear
2. Packed Pixel
3. 4 bit Linear
4. 15 bit Linear
5. 16 bit Linear
6. 24 bit Linear, the specification shows below:
a.) Multi-frequency CRT monitor (37.5KHz minimum horizontal frequency specification) [NEC MultiSync
b.) Multi-frequency high-performance CRT monitor (48.5KHz Min. H Freq. Specification) [Nanao
7. a.) The I in the mode# column indicates interlaced
b.) Max. MCLK refers to the maximum clock rate required for proper node operation.
c.) These tables reflect values found in the Chips and Technologies BIOS for the C&T F65545. If a
Color Text
20 16 80x30 8x16 640x480 Note 3 56/25.175 31.5 60
22 16 100x37 8x16 800x600 Note 3 56/40.000 37.5 60
24 16 128x48 8x16 1024x768 Note 3 65/65.000 48.5 60
24I 16 128x48 8x16 1024x768 Note 3 65/44.900 35.5 43
30 256 80x30 8x16 640x480 Note 1 56/25.175 31.5 60
32 256 100x37 8x16 800x600 Note 1 56/40.000 37.5 60
34 256 128x48 8x16 1024x768 Note 1 65/65.000 48.5 60
34I 256 128x48 8x16 1024x768 Note 1 64/44.900 35.5 43
40 32K 80x30 8x16 640x480 Note 4 65/50.350 31.5 60
41 64K 80x30 8x16 640x480 Note 5 65/50.350 31.5 60
50 16 80x30 8x16 640x480 Note 6 65/65.000 27.1 51.6
60 16 132x35 8x16 1056x400 Text 65/40.000 30.5 68
61 16 132x50 8x16 1056x400 Text 65/40.000 30.5 68
78 16 80x25 8x16 640x400 Note 2 56/25.175 31.5 70
79 256 80x30 8x16 640x480 Note 2 56/25.175 31.5 60
3D or equivalent]
Flexscan 9070s, MultiSync 5D or equivalent]
Video BIOS from another manufacturer is used these values may be different.
Display
Font
Size
Pixel
Resolution
Display
Mode
Dot Clock
(MHz)
Horizontal
Freq. (KHz)
Vertical
Freq. (Hz)
1.2 PACKING LIST
The accessories are included with the system. Before you begin installi ng your AR-B1042 board, take a moment
to make sure that the following items have been included inside the AR-B1042 package.
z The quick setup manual
z 1 AR-B1042 PC/104 VGA/LCD display board
z 1 10-pin to D-Sub 15-pin VGA CRT adapter cable
z 2 Software utility diskettes.
Caution: The Acrosser provides many various transfer boards for using, please contact the Sales department will
get more information.
1-2
AR-B1042 User’s Guide
A
1.3 AR-B1042 AND ACCESSORY LIST
The AR-B1042 is a PC/104 form factor supports VGA controller for CRT or LCD display, it is very suitable for
different types of monitors like the CRT monitor, STN, Dual-scan, TFT, Monochrome and color panels. With
512KB (or 1MB) of RAM on board, it allows a maximum CRT resolution of 1024x768x256 an LCD resolution of
640x480x64K colors. It can be connected to create a compact video solution for industrial environment.
AR-B1042 in its standard package can be used with CRT monitor thr ough the 15-pi n D-Sub co nnector provided for
interface. AR-B1042 VGA module is also available is an enhanced package for CRT/LCD display, it contains t he
standard package, plus additional accessories for using LCD flat panel display. Below table shows the list of
accessories including for both packages provided for AR-B1042 VGA module.
Description AR-B1042 for CRT
(Standard)
Interface
Provided
Accessory
Table 1-3 Standard Display
CRT Connector (DB-15)
PC/104 Standard Bus
Driver Diskettes LCD Panel Adjust VR Board
R0B1042 for LCD/CRT (With
Enhanced Accessories)
CRT Connector (DB-15)
PC.104 Connector Bus
LCD panel Interface
LCD Panel Inverter VR Board
Parts Package
Driver Diskettes
1.4 FEATURES
The system provides a number of special features that enhance its reliabi l it y, ensure its availabilit y, and improve its
expansion capabilities, as well as its hardware structure.
z IBM-VGA hardware compatible
z Supports CRT color monitors and STN, TFT, Dual-Scan STN, monochrome and color panels
z CRT resolution up to 1280x1024x16 colors
z LCD resolution up to 640x480x64K colors
z Windows performance improvement features
z Chips and Technology F65545 Chipset
z Simultaneous CRT and LCD operation
z Operating temperature 0 degree C to 70 degree C
z Up to 95% Humidity non-condensing
z PC/104 form-factor (92x97mm / 3.6”x3.8”) on a 4-layer PCB
1-3
AR-B1042 User’s Guide
2. SETTING UP THE SYSTEM
This section describes pin assignments for system’s external connectors and the jumpers setting.
z Overview
z System Setting
2.1 OVERVIEW
The AR-B1042 is a PC/104 form factor super VGA controller for CRT and LCD display board. This section
provides hardware’s jumpers setting, the connectors’ locations, and the pin assignment.
The Acrosser provides many various transfer boards for using, please contact the Sales departme nt will get more
information.
Figure 2-1 External System Location
2-1
AR-B1042 User’s Guide
2.2 SYSTEM SETTING
Before installing the AR-B1042 VGA module, you should first configure the VGA board’s hardware. This section
describes how to make connections and configure the VGA board. You may find it is convenient to go through
these sections first before installing the VGA board into the PC/104 interface.
The AR-B1042 VGA module is a very versatile VGA controller that can be used for either CRT or LCD display. It is
very important that you go through the whole chapter before installation.
Before you actually plug the module into yo ur PC/104 bus, you must first set the jumper pins to configure the ARB1042 module to your system requirements. This is done by closed the jumper pins with a jumper or leaving the
pins open.
Once you have installed the VGA card into the CPU’s PC/104 bus, you can start connect int ernal cables. The
internal cables are wire leads with plastic female connector that attached to the card’s connectors. The VGA
card’s connectors have many numbers of pins and are the points of contact bet ween the CPU card and other part s
of the computer.
CAUTION: Before making connection on the board, make sure that power to the system is turned off.
Jumper pins allow you to set specific system parameters. Set them by changing the pin location of jumper blocks.
(A jumper block is a small plastic-encased conductor [shorting plug] that slips over the pins.) To change a jumper
setting, remove the jumper from its current location with your fingers or small needle-nosed pliers. Place the
jumper over the two pins designated for the desired setting. Press the jumper evenly onto the pins. Be careful not
to bend the pins.
We will show the locations of the AR-B1042 jumper pins, and the factory-default setting.
CAUTION: Do not touch any electronic component unless you are safely grounde d. Wear a grounded wrist strap
or touch an exposed metal part of the system unit chassis. The static discharges from your fin gers can
permanently damage electronic components.
2-2
2.2.1 Universal Panel Control (CON1)
Attach a display panel connector to this 44-pin connector with pin assignments as shown below:
AR-B1042 User’s Guide
43
-- GND
41
-- DE
39
-- GND
37
-- +12V
35
-- VCC
31
-- P21
29
-- P19
27
-- GND
25
-- P16
23
-- P14
21
-- P12
19
-- P11
17
-- P9
15
-- P7
13
-- GND
11
-- P4
9
-- P2
8
6
4
7
5
3
12
-- P0
-- FLM
-- GND
-- GND
P8 -P6 -P5 -P3 --
44
42
40
38
36
34 33
32
30
28
26
24
22
20
18
16
14
12
10
VEE --
ENABLK --
GND --
+12V --
VCC --
GND -- -- P23
P22 -P20 -P18 -P17 -P15 -P13 --
GND --
P10 --
P1 --
GND --
LP --
SHFCLK --
CON1 -- Universal Panel Control
Figure 2-2 CON1: Universal Panel Control
2.2.2 VGA Monitor Connector (CON2)
CON2 is a 10-pin connector that attaches to the CRT monitor via a D-Sub 15-pin adapter cable. The pin
assignment of CON2 is shown below:
AGND -AGND -AGND -AGND --
10 -- Hsync
8
6
4
GND --
CON2 -- VGA Monitor Connector
Figure 2-3 CON2: VGA Monitor Connector
9
7
5
3
12
-- Vsync
-- Blue
-- Green
-- Red
2.2.3Panel Power Connector (CON3)
CON3 is a 5-pin connector that attaches to the Contrast and Backlight board. Its pin assignments are shown
below:
5 -- VEE
4
-- GND
3
-- +12V
2
-- ENVEE
1
-- ENABLK
CON3 -- Panel Power Connector
Figure 2-4 CON3: Panel Power Connector
2-3
AR-B1042 User’s Guide
2.2.4 PC/104 Connector
(1) 64 Pin PC/104 Connector Bus A & B (CON5)
33
64
1
-IOCHCK --SD7 --SD6 --SD5 --SD4 --SD3 --SD2 --SD1 --SD0 ---
IOCHRDY---
AEN ---
SA19 --SA18 --SA17 --SA16 --SA15 --SA14 --SA13 --SA12 --SA11 --SA10 ---
GND ---
SA9 --SA8 --SA7 --SA6 --SA5 --SA4 --SA3 --SA2 --SA1 --SA0 ---
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
A32
Figure 2-5 CON5: 64-Pin PC/104 Connector Bus A & B
(2) 40 Pin PC/104 Connector Bus C & D (CON4)
1
CON5
133
32 64
B1
--- GND
B2
--- RSTDRV
B3
--- +5 VDC
B4
--- IRQ9
B5
--- -5 VDC
B6
--- DRQ2
B7
--- -12 VDC
B8
--- -ZWS
B9
--- +12 VDC
B10
--- KEY
B11
--- -SMEMW
B12
--- -SMEMR
B13
--- -IOW
B14
--- -IOR
B15
--- -DACK3
B16
--- DRQ3
B17
--- -DACK1
B18
--- DRQ1
B19
--- -REFRESH
B20
--- BUSCLK
B21
--- IRQ7
B22
--- IRQ6
B23
--- IRQ5
B24
--- IRQ4
B25
--- IRQ3
B26
--- -DACK2
B27
--- TC
B28
--- BALE
B29
--- +5 VDC
B30
--- OSC
B31
--- GND
B32
--- GND
32
20
2-4
21
GND ---
SBHE ---
LA23 --LA22 --LA21 --LA20 --LA19 --LA18 --LA17 ---
-MEMR ---
-MEMW --SD8 --SD9 ---
SD10 --SD11 --SD12 --SD13 --SD14 --SD15 ---
KEY ---
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
C14
C15
C16
C17
C18
C19
C20
CON4
1
21
20 40
D1
--- GND
D2
--- -MEMCS16
D3
--- -IOCS16
D4
--- IRQ10
D5
--- IRQ11
D6
--- IRQ12
D7
--- IRQ15
D8
--- IRQ14
D9
--- -DACK0
D10
--- DRQ0
D11
--- -DACK5
D12
--- DRQ5
D13
--- -DACK6
D14
--- DRQ6
D15
--- -DACK7
D16
--- DRQ7
D17
--- +5 VDC
D18
--- -MASTER
D19
--- GND
D20
--- GND
40
Figure 2-6 CON4: 40-Pin PC/104 Connector Bus C & D
(3) I/O Channel Signal Description
Name Description
BUSCLK [Output] The BUSCLK signal of the I/O channel is asynchronous
RSTDRV [Output] This signal goes high during power-up, low line-voltage or
SA0 - SA19
[Input / Output]
LA17 - LA23
[Input/Output]
SD0 - SD15
[Input/Output]
BALE [Output] The Buffered Address Latch Enable is used to latch
-IOCHCK [Input] The I/O Channel Check is an active low signal which
IOCHRDY
[Input, Open collector]
IRQ 3-7, 9-12, 14, 15
-IOR
[Input/Output]
-IOW [Input/Output] The I/O write signal is an active low signal which instructs
-SMEMR [Output] The System Memory Read is low while any of the low
-MEMR
[Input/Output]
-SMEMW [Output] The System Memory Write is low while any of the low
-MEMW
[Input/Output]
DRQ 0-3, 5-7 [Input] DMA Request channels 0 to 3 are for 8-bit data transfers.
-DACK 0-3, 5-7
[Output]
AEN [output] The DMA Address Enable is high when the DMA
-REFRESH
[Input/Output]
TC [Output] Terminal Count provides a pulse when the terminal count
SBHE [Input/Output] The System Bus High Enable indicates the high byte SD8
to the CPU clock.
hardware reset
The System Address lines run from bit 0 to 19. They are
latched onto the falling edge of "BALE"
The Unlatched Address line run from bit 17 to 23
System Data bit 0 to 15
SA0 – SA19 onto the falling edge. This signal is forced
high during DMA cycles
indicates that a parity error exist on the I/O board
This signal lengthens the I/O, or memory read/write cycle,
and should be held low with a valid address
The Interrupt Request signal indicates I/O service request
[Input]
attention. They are prioritized in the following sequence :
(Highest) IRQ 9, 10, 11, 12, 13, 15, 3, 4, 5, 6, 7 (Lowest)
The I/O Read signal is an active low signal which
instructs the I/O device to drive its data onto the data bus
the I/O device to read data from the data bus
1mega bytes of memory are being used
The Memory Read signal is low while any memory
location is being read
1mega bytes of memory is being written
The Memory Write signal is low while any memory
location is being written
DMA Request channels 5 to 7 are for 16-bit data
transfers. DMA request should be held high until the
corresponding DMA has been completed. DMA request
priority is in the following sequence:(Highest) DRQ 0, 1,
2, 3, 5, 6, 7 (Lowest)
The DMA Acknowledges 0 to 3, 5 to 7 are the
corresponding acknowledge signals for DRQ 0 to 3 and 5
to 7
controller is driving the address bus. It is low when the
CPU is driving the address bus
This signal is used to indicate a memory refresh cycle
and can be driven by the microprocessor on the I/O
channel
for any DMA channel is reached
- SD15 on the data bus
AR-B1042 User’s Guide
2-5
AR-B1042 User’s Guide
s
Name Description
-MASTER [Input] The MASTER is the signal from the I/O processor which
gains control as the master and should be held low for a
maximum of 15 microseconds or system memory may be
lost due to the lack of refresh
-MEMCS16
[Input, Open collector]
-IOCS16
[Input, Open collector]
OSC [Output] The Oscillator is a 14.31818 MHz signal
-ZWS
[Input, Open collector]
Table 2-1 I/O Channel Pin Assignment
The Memory Chip Select 16 indicates that the present
data transfer is a 1-wait state, 16-bit data memory
operation
The I/O Chip Select 16 indicates that the present data
transfer is a 1-wait state, 16-bit data I/O operation
The Zero Wait State indicates to the microprocessor that
the present bus cycle can be completed without inserting
additional wait cycle
2.2.5 Setting Linear Address (J1 & J2)
J2
J1
J2
J1
3
2
1
Linear Address
Factory Preset
Figure 2-7 J1 & J2: Setting Linear Address
2.2.6 Setting Clock Source (J3)
J3
1
2
On-Board
Factory Preset
Figure 2-8 J3: Setting Clock Source
2.2.7 DE/E Signal from M or LP (J4)
3
2
1
3
2
1
3
2
1
Non-Linear Addres
3
12
3
PC/104 Bus (System)
J4
1
2
3
1
2
3
2-6
DE/M
Factory Preset
Figure 2-9 J4: DE/E Signal from M or LP Select
E/LP
2.2.8 Setting BIOS Bank (J5)
J5
AR-B1042 User’s Guide
1
2
3
Upper 32KB
DSTN VGA LCD or TFT
12
3
Lower 32KB
Dual Mono VGA LCD
Factory Preset
Figure 2-10 J5: Setting BIOS Bank
BIOS BANK FUNCTION
Upper 32KB DSTN VGA LCD or TFT
Lower 32KB Dual Mono VGA LCD
Table 2-2 Setting BIOS Bank
2-7
3. CRT/LCD FLAT PANEL DISPLAY
This section describes the configuration and installation procedure using LCD and CRT display.
z Board Installation
z Connecting the CRT Monitor
z LCD Flat Panel Displa y
z Supported LCD Panel
z Inverter Board Description
3.1 BOARD INSTALLATION
After setting the board’s jumpers, install the AR-B1042 module as follows:
Step 1 :
Step 2 :
Step 3 :
Step 4 :
Make sure that the power to the system is off.
Locate the PC/104 bus connector on the AR-B1042 VGA module and its counter part on the CPU
card.
Align the PC/104 bus connector pins on the AR-B1042 module with the CPU’s connector and ge ntly
press the two cards firmly together.
Fasten the two cards together with the screws.
AR-B1042 User’s Guide
Acrosser's
CPU Card
AR-B1042
Figure 3-1 LCD Panel Block Diagram
3.2 CONNECTING THE CRT MONITOR
To connect a CRT monitor, an adapter cable has to be connected to the CON2 (10-pin header type) connector.
This adapter cable is included in your AR-B1042 package.
3-1
AR-B1042 User’s Guide
3.3 LCD FLAT PANEL DISPLAY
This section describes the configuration and installation proc edure using LCD display. S kip this section if you are
using CRT monitor only.
J5 is used to configure the BIOS default setting for different types of LCD panel. To set your system properly,
configure you AR-B1042 VGA module for the right type of LCD panel you are using by opening or shorting the
jumper located at the component side of the AR-B1042 module labeled as J5.
The sample LCD models listed on the table are just some of the LCD panel mod els avail able in the mar ket that the
Chips & Technologies used by AR-B1042 VGA module can support. If you are using a different LCD panel other
than those listed, choose from the panel description column which type of LCD panel you are using.
The following shows the block diagram of using AR-B1042 for LCD display.
AR-B1042
VGA
LCD
Panel
Module
VBL Control
VEE
+12V, +5V
Inverter
Board
Figure 3-1 LCD Panel Block Diagram
The block diagram shows that AR-B1042 still needs components to be used for LCD panel. The inverter board
provides the control for the brightness and the contrast of the L CD panel while the inverter is the one th at supplies
the high voltage to drive the LCD panel. Each item will be explained further in the section.
FL HIGH
Voltage
CON3
AR-B1042
VGA
Module
Inverter & Contrast
CON1
Pin 1
Pin 1
LCD
Panel
Figure 3-2 LCD Panel Cable Installation Diagram
NOTE: Be careful with the pin orientation when installing connectors and the cables. A wrong connection can easily
destroy your LCD panel. The pin 1 of the cable connectors is indicated with a sticker and the pin 1 of the
ribbon cable is usually with different color.
3-2
AR-B1042 User’s Guide
3.4 INVERTER BOARD DESCRIPTION
The inverter board is the one that supplies the high voltage signals to drive the LCD p anel b y converting the 12 vol t
signal from the AR-B1042 into high voltage AC signal for LCD panel.
It can be installed freely on the space provided over the VR board. If the VR board is installed on the bracket, you
will have to provide a place to install the inverter board into your system.
3-3
AR-B1042 User’s Guide
4. INSTALLATION OF THE UTILITY SOFTWARE
This chapter describes the installation of the utility software. The following topics are covered:
z Install Application Software
z The CHIPSDSP Utility Program
z The CHIPSCPL Utility Program
z The SETCOL Utility Program
4.1 INSTALL APPLICATION SOFTWARE
4.1.1 Windows 3.1
These drivers are designed to work with Microsoft Windows Version 3.1. You may install these drivers either
through Windows or in DOS.
(1) Driver Installation – Windows Setup
Step 1 :
Step 2 :
Another method of installing these drivers is through the Fi le Manager. Cl ick on Drive A:, and t hen doub le-click on
WINSETUP.EXE to begin installation.
(2) Changing Display Drivers from Windows
To change display drivers from Windows, select the Windows Setup icon from the Main window. You will be
shown the current setup configuration. Select Change System Settings from the Option menu. Click on the arrow
at the end of the Display line. You will be shown a list of display drivers. Click on the driver you want to select.
Then click on the OK button. Follow the directions to complete the setup.
(3) Changing Color Schemes
After you change display drivers, you may notice that the color scheme used by Windows looks strange. This is
because different drivers have different default colors. You can correct this by choosing the same color scheme or
a new color scheme. First select the Control Panel from the Main window. Select the Color icon. You will be
shown the current color scheme. Choose a new color scheme and click the OK button.
Install Windows as you normally would for a VGA display. Run Windows to make sure that it is
working correctly.
Place the Display Driver Diskette#1 in drive A. In Windows Program Manager, choose File from the
Options Menu. Then from the pull-down menu, choose Run… At the Command Line prompt, type
A:\WINSETUP. Press the <ENTER> key or click OK to begin the installation. At this point the setup
program locates the directory where Windo ws is installed. For proper operation, the drivers must be
installed in the Windows sub-directory. Press <ENTER> to complete the installation. Once
completed, the Display Driver Control Panel appears o n the screen. This Control Panel allows you
to select and load the installed drivers.
4-1
AR-B1042 User’s Guide
(4) Driver Installation – DOS Setup
Step 1 :
Step 2 :
Step 3 :
Step 4 :
Step 5 :
Install Windows as you normally would for a VGA display. Run Windows to make sure that it is
working correctly. Then exit from Windows.
Place the Display Driver Diskette #1 in drive A. Type A: <ENTER> to make this the default drive.
Type SETUP <ENTER> to run the driver SETUP program. Press any key to get to the applications
list. Using the arrow keys, select Windows Version 3.1 and press the <ENTER> key. Press the
<ENTER> key to select <All Resolutions>, then press<END> to begin the installati on. At this point
you will be asked for the path to your Windows System directory (default C:\WINDOW S). When the
installation is complete, press any key to continue. Press <ESC> followed by Y to exit to DOS.
Change to the directory where you installed Windows (usually C:\WINDOW S).
Type SETUP <ENTER> to run the Windows Setup program. It will show the current Windows
configuration. Use the up arrow key to move to the Display line and press <ENTER>. A list of
display drivers will be shown. Use the arrow keys to select one of the drivers starting with an
asterisk (*) and press <ENTER>.
Follow the directions on the screen to complete the setup. In most cases, you may press <ENTER>
to accept the suggested option. When Setup is done, it will return to DOS. T ype WIN <ENTER> to
start Windows with the new display driver.
(5) Changing Display Drivers from DOS
To change display drivers from DOS, change to the Windows directory and run Setup repeating step 4 and 5 in the
section of <Driver Installation – DOS Setup>. Besides the special display drives marked by an asterisk (*), you
should be able to use the following standard drivers:
VGA
Super VGA
Table 4-3 Display Driver Colors
640x480, 16 colors
800x600, 16 colors
4.1.2 Panning Drivers
Special panning drivers are provided to allow high-resolution modes to be displayed on a flat panel or CRT . These
drivers will show a section of a larger screen, and will automatically pan or scroll the screen horizontally and
vertically when the mouse reaches the edge of the display.
4-2
AR-B1042 User’s Guide
4.1.3 AutoCAD R12
These drivers are designed to work with AutoCAD R12. They conform to the Autodesk Device Interface (ADI) for
Rendering drivers and Display drivers. These display drivers accelerate redraw, pan, and zoom functions.
(1) Driver Installation
To install the drivers, follow these instructions:
Step 1 :
Step 2 :
(2) Configuring TurboDLD Driver
Select Configure Video Display. In Display Device Configuration choose Select Graphics Board/Resolution. Then
choose Select Display Graphics Board. After choosing a Graphics Board, go to Select Display Resolution. After
selected Display Resolution, save the new configuration and return to the main menu.
1. Basic Configuration Menu
This menu allo ws you to modify:
2. User Interface Configuration
3. Expert Configuration Menu
This menu allo ws you to modify:
Place the Display Driver Diskette #1 in drive A. Type A: <ENTER> to make this the default drive.
Type SETUP <ENTER> to run the SETUP program. Press any key to get to the applications list.
Using the arrow keys, select AutoCAD Release 12 and press <ENTER>. This will display a list of
supported driver resolutions. Using the arrow keys and the <ENTER> key, select the resolutions
that are appropriate for your monitor. When all of the desired resolutions have been sel ected, press
<END> to begin the installation. At this point you will be asked for a drive and directory to copy the
driver files. Enter the drive and directory that contains the insta lled AutoCAD R12. You may be
asked to change display driver diskettes, and if the destin ation directory does not exist you will be
asked for confirmation. When the installation is complete, press any key to continue. Press <ESC>
followed by Y to exit to DOS.
Go to the AutoCAD directory where the new drivers were installed and run the driver installation
program by typing ACAD12 –r <ENTER>. This progr am will confi gure your AutoCAD R1 2 to use t he
new display drivers. Select TurboDLD Classic.
• Number Of AutoCAD Command Lines
• Screen Configuration Dual/Single/Text Window on Single
• Select Font from List 6x8/8x8/8x14/8x16/12x20/12x24
• Select Font Filter All Fonts/IS08859/jisx0201.1976
• Double Click Interval Time
• BP Button
• BP Highlight
• BP Refresh
• Display List
• Use Acad 31 bit space?
• Internal Command Echo
• BP Zoom Mode
• Disable DL in PSpace?
Patt. Line/Xor Rect/Both
Enable/Disable
Enable/Disable
Yes/No
Enable/Disable
Freeze/Float
Yes/No
4-3
AR-B1042 User’s Guide
If you have previously installed a driver different from the TurboDLD driver, please note the following:
After installing the TurboDLD Classic, when running the Render Command, AutoCAD R 12 will take you into
AVE_RENDER to reconfigure Render for your new driver.
4.1.4 Lotus 1-2-3 Lotus Symphony
These drivers are designed to work with Lotus 1-2-3 Version 2.0, 2.01 and 2.02, and with Lotus Symphony Version
1.0 and 1.1.
To install the Lotus drivers, follow this procedure:
Step 1 :
Step 2 :
Step 3 :
Step 4 :
Step 5 :
Step 6 :
Step 7 :
NOTE:
Place Display Driver Diskette#1 into drive A. Make A the default drive by t yping A:<ENTER>. Run
the SETUP program by typing SETUP <ENTER>. Press any key to display a list of supported
applications. Use the arrow keys to select Lotus/Symphony and press <ENTER>. A list of
supported screen resolutions will be displayed. Use the arrow keys to select the desired screen
resolution and press <ENTER > (make sure your monitor is able to displa y the resolution desired).
Press <END> to begin the driver installation process. A default drive and directory path will be
displayed. Use the backspace key to erase this d efault and type in the 123 directory. At this point
you may be prompted to insert one of the other driver diskettes. You also may be asked to create
the target directory if it does not already exist. After the files have been installed, press any key to
return to the list of supported applications. Press <ESC> followed by Y to exit to DOS. Copy all the
files that were just created on the temporary directory onto a formatted floppy diskette.
Go to your 123 directory and start the installation program. Type the following commands:
C:<ENTER>
INSTALL <ENTER>
The Lotus installation program will load and present the installati on menu. From this menu, select
Advanced Options. From the Advanced Options menu, select Add Ne w Drivers To Library From the
Add New Drivers Menu, select Modify Current Driver Set. From the Modify Driver Set Menu, select
Text Display. From the Text Display menu, select one of drivers.
After the selection of the appropriate VGA display driver, you will need to exit this menu and return to
the Main Lotus Installation Menu. Do this by selecting Return to Menu.
At the Main Lotus Installation Menu, select Save Changes
At this point the Installation Menu will prompt you for the name of your new Lotus configuration file.
The Lotus system will prompt you with the default value 123.SET. You do not have to use this
name, however. You may want to use a filename that indicates the resolution of the driver it
contains. For example, if you installed the 123 column by 25 li ne driver, you could name this driver
132x25. SET. Or if you installed the 80 by 50 driver, you many want to call the file 80x50.SET.
The installation of your Lotus 1-2-3 driver is now complete. You will need to exit the Lotus
installation program at this point. At the main Lotus Installation Menu, select Exit.
If you use a different name of the driver set than 123.SET, you have to remember to place the
filename of your driver set on the command line when you start Lotus 1-2-3. For example, if you
named your driver set 132x25.SET, give the following command to start Lotus 1-2-3:
123 132x25.SET <ENTER>
4-4
AR-B1042 User’s Guide
4.1.5 Word
These drivers are designed to work with Microsoft Word Version 5.0 and 5.5.
If you have already installed Word on your computer go to Step 2 install the new video driver.
Step 1 :
Step 2 :
Step 3 :
Install Word as you normally would.
After you complete the Word installation, place the Display Driver Diskette #1 into drive A. Make A
the default drive by typing A:<ENTER>. Run the SETUP program by typing SETUP <ENTER>.
Press any key to display a list of supported applications. Use the arrow keys to select Word and
press <ENTER>. Use the arrow keys to select the desired screen resolution and press <ENTER>
(make sure your monitor is able to display the resolution desired). Press <END> to begin the driver
installation process. A default drive and directory path will be displaye d. Use the backspace key to
erase this and type in your Word directory. At this point you may be prompted to insert one of the
other driver diskettes. After the files have been installed, press any key to return to the list of
supported application. Press <ESC> followed by Y to exit to DOS.
Copy the driver file for the desired resolution that was just installed to SCREEN.VID.
4.1.6 WordPerfect
These drivers are designed to work with WordPerfect Version 5.0 or 5.1. They support 132-column display in
editing mode, and high-resolution graphics display in preview mode.
(1) Driver Installation
Step 1 :
Step 2 :
(2) Configuring WordPerfect 5.0 for 132 columns
Follow these instructions to configure WordPerfect 5.0 for 132 column text mode:
Step 1 :
Step 2 :
(3) Configuring WordPerfect 5.1 for 132 columns
Start WordPerfect and press <SHIFT>+<F1> to enter the setup menu. Select D for Display and T for T ext Screen
Type and then select Chips 132 Columns Text.
Place Display Driver Diskette #1 into drive A. Make A the default drive b y typing A:<ENTER>. Run
the SETUP program by typing SETUP <ENTER>. Press any key to display a list of supported
applications. Use the arrow keys to select WordPerfect and press <ENTER>. A list of supported
screen resolutions will be displayed. Use the arrow keys to select the desired scre en resolution and
press <ENTER> (make sure your monitor is able to display the resolution desired). Press <END> to
begin the driver installation process. A default drive and directory path will be displayed. Use the
backspace key to erase this default and type in the WordPerfect directory. At this point you may be
prompted to insert one of the other driver diskettes. You also may be asked to create the target
directory if it does not already exist. After the files have been installed, press any key to return to the
list of supported applications. Press <ESC> followed by Y to exit to DOS.
Start WordPerfect and press <SHIFT>+<F1> to enter the setup menu. Select D for Display and G
for Graphics Screen Type and then choose the desired Chips VGA resolution.
Use the SETCOL program to set 132 columns and 25 rows. Give the following command:
SETCOL 132, 25 <ENTER>
Start WordPerfect. The program will detect the number of rows and columns automatically. If for
some reason WordPerfect is unable to adapt to 132 columns by 25 rows, start WordPerfect with the
following command:
WP /SS=25,132 <ENTER>
4-5
AR-B1042 User’s Guide
4.1.7 Windows NT
These drivers are designed to work with Microsoft Windows NT 3.5x.
Step 1 :
Step 2 :
Step 3 :
Install Windows NT as you normally would for a VGA display. Run Windows NT Control Panel from
the Main Group. Choose the Display option. In the Disp lay Settings dialog box, click on Change
Display Type. Click on Change from the Adapter Type in the Display Type dialog box. Click on
Other in the Select Device dialog box.
Place the Windows NT Display Driver Diskette in drive A. Press <ENTER> and the following names
of the driver:
CHIPS Video Accelerator (65545,65548)
CHIPS Video Controller (65510,65530,65535,65540)
Will appear highlighted in the Models list box. Click on INSTALL to install the selected driver. Once
the installation is complete, the system must be shut down and restarted.
Upon restart, at the Invalid Display Selection message, click on OK and select the desired display
settings from the Display Settings dialog box. Click on Test to test the newly selected graphics
mode. A color test screen should appear, followed by the Testing Mode window. Click on Yes to
continue. The Display Settings Change windows will appear. Click on Restart Now for the new
settings to take effect.
4.2 THE CHIPSDSP UTILITY PROGRAM
This utility program is designed to work with Microsoft Windows 95.
4.2.1 Installing the Utility
CHIPSDSP.DLL is a Windows 95 based utility to select display t ype and refresh rate. It is a Display Properties
Refresh window that is automatically installed when installing CHIPS Windows 95 dis play drivers. The Display
icon is in the Control Panel group. To invoke the Displa y icon, simply click on the Start button, g o to Settings and
click on Control Panel.
4.2.2 How to Use the Utility
DISPLAY DEVICE allows you to select the display type from the following:
• CRT only <ALT C>
• LCD (Flat Panel) only <ALT L>
• Both CRT and LCD (Flat Panel) <ALT B>
REFRESH RATE allows you to select the refresh rate from the following:
• Interlaced
• 56 Hz
• 60 Hz
• 70 Hz
• 72 Hz
• 75 Hz
The refresh rate is available in CRT Mode only and only the refresh rates supported by t he selected monitor will be
listed.
WINDOWS DEFAULT allows you to return to the default refresh rate setting for the selected monitor in Windows
95.
4-6
AR-B1042 User’s Guide
4.3 THE CHIPSCPL UTILITY PROGRAM
This utility program is designed to work with Microsoft Windows Version 3.1.
4.3.1 Installing the Utility
CHIPSCPL.CPL is a Windows based utility to select resolutions a nd color depth. It is a control Panel Applet with
its own icon that is automatically installed when installing Chips Windows 3.1 Linear drivers. The Control Panel
icon is in the Main Windows group. To invoke the control panel applet, simply click on the icon. The driver
resolution and color depth take effect only after Windows is rebooted with the new driver.
4.3.2 How to Use the Utility
SCREEN SIZE <ALT S> allows you to select from the following resolutions:
• 640x480
• 800x600
• 1024x768
• 1280x1024
By selecting the resolution first, it will determine the allowable selections for color depth.
COLOR <ALT O> allows you to select the number of colors from the following:
• 16 (4 bits per pixel)
• 256 (8 bpp)
• 32K (15 bpp)
• 64K (16 bpp)
• 16M (24 bpp)
By selecting the color depth first, it will determine the allowable selections for resolution.
DPI <ALT P> allows you to select a large or small font.
DISPLAY <ALT D> allows you to select the display type from the following:
• CRT only
• LCD (Flat Panel) only
• Both CRT and LCD (Flat Panel)
MONITOR SELECTION <ALT M> allows you to select from the list of monitors.
REFRESH <ALT R> allows you to select the refresh rate from the following:
• Interlaced
• 56 Hz
• 60 Hz
• 70 Hz
• 72 Hz
• 75 Hz
The refresh rate is available on CRT Mode only. The refresh rates supported by the sele cted monitor are the only
available refresh rates that can be selected.
CURSOR-ANIMATION <ALT A> allows you to select an animated cursor instead of the hour glass wait cursor.
BIG CURSOR <ALT G> allows you to select a big cursor for better visibility on the Flat Panel.
4-7
AR-B1042 User’s Guide
VERSION <ALT V> displays version information about the current driver.
HELP <ALT H> displays help information on how to use the display Driver Control Panel.
FONT SIZE <ALT F> (Japanese Windows only) allows you to select the font size from the following:
• 12
• 16
• 20
• 24
NOTE: The CHIPSCPL will prompt for Windows 3.1 and/or Chips driver disk(s) if required files are missing.
4.4 THE SETCOL UTILITY PROGRAM
This utility program is used to provide 132 text columns in popular text-based applications such as WordStar and
WordPerfect. If you do not intend to use 132 column text mode, do not install this utility.
4.4.1 Installing the Utility
To install the utility, follow this procedure:
Step 1 :
Step 2 :
Determine where you want to stone the program. Locate a directory on your hard disk where you
have other utility programs. For your convenience, this directory should be specified in the
PATH=statement in your AUTOEXEC.BAT file.
Place Display Driver Diskette #1 into drive A. Make A the default drive b y typing A:<ENTER>. Run
the SETUP program by typing SETUP <ENTER>. Press any key to display a list of supported
applications. Use the arrow keys to select Utilities and press <ENTER>. A list of utilities will be
displayed. Use the arrow keys to select the utilities desired and press < ENTER>. Press <END> to
begin the utility installation process. A default drive and directory path will be displayed. Use the
backspace key to erase this default and type in the proper directory. At this point you may be
prompted to insert one of the other driver diskettes. You also may be asked to create the target
directory if it does not already exist. After the files have been installed, press any key to return to the
list of supported applications. Press <ESC> followed by Y to exit to DOS.
4-8
AR-B1042 User’s Guide
4.4.2 How to Use the Utility
The SETCOL utility program allows you to s pecity the number of rows and columns on the screen. You in dicate
these values to the SETCOL program by placing them after the name SETCOL on the command line. The format
for the command is:
SETCOL COLUMNS,ROWS <ENTER>
Valid values for columns and rows are:
Columns Rows
80 or 132 25 or 50
Table 4-4 The Values for Columns and Rows
If you want to set 132 columns with 25 rows, give the following command:
SETCOL 132,25 <ENTER>
Note 1 :
Note 2 :
To use this program with an application program such as WordStar or WordPerfect, the applicatio n
may need to be configured for the specific screen size. Please refer to other sections in this manual
on how to configure your applications for this.
Certain monitors cannot display 50 character rows on the screen, due to hardware limitations in
these monitors. The following table specifies how many rows can be displayed on common
monitors:
Monitor Rows
IBM Monochrome 25
IBM Color Graphics Display 25
IBM Enhanced Graphics Display 25
IBM VGA Display (analog) 25 or 50
Multi-Frequency Display 25 or 50
Table 4-5 Monitor Display the Rows
4-9
AR-B1042 User’s Guide
5. ERROR (BEEP) CODES & INDEX
5.1 ERROR (BEEF) CODES
There are three possible beep codes produced by the BIOS during POST listed below:
Beep Code Error Condition
1 long followed by 2 short beeps CMGA card failure
1 long followed by 3 short beeps RAM test failure
1 long followed by 4 short beeps DAC test failure
1 long followed by 8 short beeps VGA initialized failure
Table 5-6 Error (Beef) Codes
If you have problems after installation, check the following to determine the cause.
1. Ensure that all cable are properl y connected, all plugs are firmly seated in their sockets. Check to see if the
VGA and LCD is firmly seated in its bus PC/104. Be sure it is not making contact with any other cards in
the system.
2. Ensure that the display monitor is properl y connected to computer. Be sure the display monitor and your
system’s power supply is operating properly (i.e. FAN operates, system power light come on). Power OFF
the computer system and all other connector devices before checking the following:
3. Ensure that the system motherboard switch’s/jumper(s) are set properly for use with the VGA board.
4. Ensure that no other switch setting on the CPU card have been accidentally change. Refer to the
documentation provided with you computer to determine the corrector switch settings.
5. Be sure the CLMODE.EXE setting match you monitor frequency.
6. Ensure the LCD panel’s VEE and BACKLIGHT voltage (adjust VR)
If checking these items does not locate the problem, there may be a malfunction of the computer system, display
monitor or the VGA and LCD board. Consult you computer dealer for assistance in locating the problem.
5.2 INDEX
Name Function Page
CON1 Universal panel connector 2-3
CON2 10-pin VGA monitor connector 2-3
CON3 Panel power connector 2-3
CON4 40 pin PC/104 connector bus C & D 2-4
CON5 64 pin PC/104 connector bus A & B 2-4
J1 & J2 Linear address select 2-6
J3 Clock select 2-6
J4 Panel select 2-6
J5 BIOS bank select (set panel type) 2-7
U1 BIOS Flash
U4 & U5 RAM socket
Table 5-7 Index
5-1
Loading...