AcousticSheep Effortless User Manual

INSTRUCTIONS

ANLEITUNG

INSTRUCCIONES

ISTRUZIONI

Scan this QR code or visit www.SleepPhones.com/instructions

to read this User Guide as well as Warranty Information and

Legal disclosures in additional languages.

WEARING YOUR EFFORTLESS

Holding the headphones, you’ll notice the at speakers –

1

one on each side – inside of the headband.

Place the headband on your head (tag

2

goes at the back of your head).
Once the headband is on,

3

adjust the speakers so they
are positioned directly over
your ears. This will ensure
great sound quality.

Please Note: The speakers
move inside of the headband,
independently of the headband.

INSTRUÇÕES

說明書
说明书

指示書

명령

تعليمات

™

HEADPHONES

BASIC EFFORTLESS

Up Arrow

Down Arrow

Power On: Press and hold
center button for 5 seconds

Volume: Click the arrows to
increase or decrease the volume

™

HEADPHONE USAGE

Bluetooth® Module

Skip Tracks: Double click

arrows to skip tracks

Play/Pause: Click the center
button once to play or pause

Center Button

Power Off: Press and hold the middle square button on the
Bluetooth® module for 3 seconds until you hear descending
tones through the speakers

PAIRING YOUR EFFORTLESS

Remove the Bluetooth® module from the hook

1

™

HEADPHONES

and loop opening at the back of the headband.
Hold down the square

2

button for 5 seconds
until you hear
ascending tones
through the speakers

5s

3ft (1m)

followed by a series of
double beeps and a fast
blinking red light. Must be
within 3 feet (1 meter) of
your device.

On your device, make sure

3

Bluetooth® is turned on. Look for
‘ACOUSTICSHEEP’ and select to
pair. Pairing may take up to 30 seconds.

EFFORTLESS™ CHARGING INSTRUCTIONS

Assemble charging mechanism (micro-USB into

1

Effortless™ base*, USB into wall adapter**)
and plug USB adapter into
wall outlet.

Your Effortless™ base will have
a solid orange light indicating
that it is ready to be used.

Lay your Effortless™

2

headband on the
base with the module

Headband

(module inside)

Charging Base Cord

(in opposite direc tion

of spea ker cord)

inside, buttons facing
down, and the plugs in
opposite directions.

Your Effortless™ is charged when the

3

Speaker Cord

(in opposite direc tion

of charging base cord )

LED

light on the base is solid green (it will
take approximately 3 hours to fully
charge).

Effortless™ LEDs

Solid : Powered on, no device connected

Blinking : Effortless™ is charging correctly

Blinking : Improper charging position

Solid : Effortless™ is fully charged

Inser ting the mic ro-USB into the base u pside down could da mage it and prevent it f rom charging.

*

Use onl y the cable and wall adapter p rovided.

**

WASHING INSTRUCTIONS

Open the hook and loop at the

1

back of the headband to reveal
the speaker components inside
the headband.

Remove the Bluetooth®

2

L

R

module and then reach in to
remove the speakers, one at
a time, from the headband.

Once the speakers are

3

removed, you can machine­wash the headband.

Reinsert one speaker at a time, and move each about four

4

inches from the hook and loop opening on either side of
the headband.

• Right speaker has red stitching

• Left speaker has green stitching

• Softer gray side should face towards the ear

• White side should face away from the ear

Then insert the Bluetooth® module into the headband and

5

close the hook and loop opening.

PROLONG THE LIFE OF YOUR HEADPHONES

• When disconnecting the cord, grasp and pull the plug
and not the cord.

• Do not leave components in a wet or dirty headband.

• Wash your headband regularly (remove all components
before washing).

/ / / /

TROUBLESHOOTING

Not Sure if Fully Charged? Refer to “Effortless™ LEDs” chart.

Unable to Pair for the First Time? When you turn on the

module, make sure to continue holding down the button for
a full 5 seconds until you hear ascending tones followed by
a series of beeps. The beeps indicate that the module is in
pairing mode.

Unable to Pair? If your Bluetooth® enabled device is unable
to pair with the Bluetooth® module, you may need to reset the
module and/or your device. To reset the Bluetooth® module,
turn it on then hold both the “up” and “down” arrow buttons
down for 7 seconds. Once the reset function is complete, there
will be 2 long tones. The Bluetooth® module must be turned
off and then turned back on for it to enter into pairing mode.

Unable to Find Device while Pairing? If your AcousticSheep®
module was previously paired with another device, it will
automatically pair with that device if the device is within range.
Make sure that the Bluetooth® on all other previously paired
devices is turned off when you are pairing with a new device.

No Sound When Paired

• Slide the speakers inside the headband (gray side of
speakers towards the ear) to position them over your ears.

• Check the volume on your Bluetooth® audio player and
wireless Bluetooth® module located inside the headband.

• Make sure the wireless Bluetooth® module is charged.

• If your paired Bluetooth® device is separated from your
SleepPhones® Effortless™ headphones for more than 5
minutes, the headphones will automatically power off. Try
powering them back on (not all apps or software support
Bluetooth®).

• Turn off the module and restart the pairing process.

WARRANTY INFORMATION AND LEGAL DISCLOSURES

BATTERY

This AcousticSheep® product contains a rechargeable lithium ion battery. It should only
be charged with the charging cable and wall adapter provided with this product. Lithium
batteries last longer if they are charged after every use. They do not need (and prefer not)
to be fully discharged before recharging. AcousticSheep® provides a battery replacement
and recycling service that you can access through our website. Please DO NOT attempt
to open this product or replace the battery yourself. Opening the product voids the
limited warranty.

WARNINGS

WARNING: SleepPhones® or RunPhones® may be a strangulation hazard. They should
not be used by children, the elderly, or by anyone who may strangulate on the cord.

WARNING: Use of a headset that covers both ears will impair your ability to hear other
sounds. Use of such a headset while operating a motor vehicle or riding a bicycle may
create a serious hazard to you and/or others, and is illegal in most states and regions.

WARNING: Exposure to high volume sound levels may damage your hearing.
The louder the volume, the less time is required before your hearing could be affected.
You may experience different sound levels when using your headset or headphones
with different music and different devices. If you experience hearing discomfort, you
should stop listening to the device through your headset or headphones and have your
hearing checked by your doctor.

To protect your hearing, hearing experts suggest that you:

• Set the volume control in a low position before putting your headset or
headphones on your ears and use them at the lowest possible volume.

• Avoid turning up the volume to block out noisy surroundings. Whenever possible, use
your headset or headphones in a quiet environment with low background noise.

• Limit the amount of time you use headsets or headphones at high volume levels.

• Turn the volume down if the sound from the headset or headphones prevents you
from hearing people speaking near you.

If you live in North America and still can’t nd the information you need, please

call our customer service team for assistance before returning the products to your
retailer under their return policy.

Tel: [phone] Email: [e-mail]
If you live outside of North America, please visit our website www.SleepPhones.com

or www.RunPhones.com to locate your country’s distributor.

Bluetooth® Wireless Headphones
AcousticSheep LLC

FCC NOTICE TO USERS FCC ID: S9HZJRNFY10

Changes or modications not expressly approved by AcousticSheep LLC could void the

user’s (or your) authority to operate the equipment. This device complies with part 15
of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the
following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

For the product FCC registration label, please see the Bluetooth® wireless module
contained inside of the headband.

RF EXPOSURE

THIS DEVICE MEETS INTERNATIONAL GUIDELINES FOR EXPOSURE TO RADIO WAVES.
It is designed not to exceed the limits for exposure to radio waves recommended by
international guidelines.

This equipment complies with IC radiation exposure limits set forth for an uncontrolled

environment. End users must follow the specic operating instructions for satisfying RF

exposure compliance.

DECLARATION OF CONFORMITY

AcousticSheep LLC declares that this product is in compliance with:

• The essential requirements and other relevant provisions of Directive 1999/5/EC

• All other relevant EU Directives.

In compliance with WEEE Directive (2002/96/EC), please dispose of this
product by taking it to your local collection point or recycling center for
electronic devices.

These statements have not been evaluated by the Food and Drug Administration. This
product is not intended to diagnose, treat, cure, or prevent any disease.

• Limit the amount of time you use headsets or headphones at high volume levels.

• Turn the volume down if the sound from the headset or headphones prevents
you from hearing people speaking near you.

LIMITED ONE-YEAR WARRANTY

Please refer to www.SleepPhones.com/warranty for full details regarding the
AcousticSheep LLC Limited Warranty.

CUSTOMER SERVICE

The answers to most setup and performance questions can be found in the FAQs at
www.SleepPhones.com/faqs or www.RunPhones.com/faqs.

Visit www.SleepPhones.com/instructions to read this User Guide as well as Warranty
Information and Legal disclosures in additional languages.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth® SIG, Inc., and any
use of such marks by AcousticSheep LLC are under license. Other trademarks and trade names are those
of their respective owners.

© 2018 AcousticSheep LLC. All rights reserved. SleepPhones®, RunPhones®, the SleepPhones® logo,
the RunPhones® logo, and “pajamas for your ears” are trademarks or a registered trademark of
AcousticSheep LLC. Unauthorized duplication is a violation of applicable law. US Patent No. 8,213,670
and 9,924,271. Other US and international patents pending.

/

Bluetooth® Wireless Headphones with Induction Charging

USER GUIDE

Welcome to the

AcousticSheep® Family!

This User Guide has helpful tips and info for

using and enjoying your new AcousticSheep®

SleepPhones® or RunPhones® Effortless™.

Still have questions? Contact our customer service

team M-F from 8-5pm EST at 877-838-4790 or

at [e-mail].

Enjoy!

/

AS-E-UG-01

/ /