Acoustic Research AWS5B3 User Manual

There are two options to power your wireless speaker: using the included AC power adapter or using 6 AA batteries (not included).

Note: Be sure to use the speaker AC power adapter rated 9V DC 1200 mA.

Warning: This product is water-resistant, not waterproof. Avoid prolonged exposure to wet

environments, such as rain, mist, dew, etc. In other words, you can take it out, just don’t leave it out. To avoid electrical shock, use this product with caution near water sources if powered with the AC adapter. Never submerge in water.

AA Batteries

1. Remove the battery compartment cover on the bottom of the speaker.

2. Insert six (6) AA batteries (not included) into the speaker following the polarity (”+” and “-”) as diagrammed inside the battery compartment.

3. Replace the battery compartment cover on the bottom of the speaker.

Note: Place the rubber cap in the speaker power input jack when using batteries.

DO NOT mix batteries with different chemistry types (for example, a zinc battery with an alkaline

battery). when not in use for long periods. Always remove old, weak or worn-out batteries promptly and recycle or disp ose of the m in acco rdance wit h local and natio nal regul ations.

Introduction

The AWS5B3 portable wireless speaker is the ultimate in portable sound that goes wherever you go. Bluetooth wireless lets you stream and control your music from any Bluetooth- enabled wireless product, great for anywhere you are. The 900MHz wireless transmitter gives you 150ft of room to roam from your audio source, great for outdoor entertaining at home. And the speaker’s 3.5mm jack offers a convenient direct connection option to use everywhere in between—just connect your MP3 player and enjoy.

This manual shows you how to set up all three connection options: Bluetooth wireless, 900MHz wireless, and the direct connect jack, beginning with a tour of the speaker and included accessories. If, after having reviewed the instructions, you have any questions, please call toll-free 1-800-732-6866 or visit www.acoustic-research.com.

Important Information

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION

Caution: To reduce the risk of electric shock, do not remove cover (or back). No

user serviceable parts inside. Refer servicing to qualiﬁ ed service personnel.

Product Information

Keep your sales receipt to obtain warranty parts and service and for proof of purchase. Attach it here and record the serial and model numbers in case you need them. These num bers are located on the product.

Model No.: _____________________________________________________________________________________________

Purchase Date: _________________________________________________________________________________________

Dealer/Address/Phone: __________________________________________________________________________________

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. H eed all warni ngs.

4. Follow all in structions.

5. Clea n only with dry cloth.

6. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

7. D o n o t i n st a l l ne a r an y he a t so u rc e s s u ch a s ra d i a t o r s , he at r e g i st e r s , s t o v e s , o r o th er a pp a ra t u s (i nc lu di ng a mp li ﬁ ers) that produce heat.

8. Protect the power cord from being walked on or pinched particularly at plugs, con ve nience re cep ta cles, and the point where they exit from the apparatus.

9. Unp lug this app arat us d urin g li ghtn ing stor ms o r w hen unus ed f or l ong peri ods of t ime.

10. Refer all servicing to qualiﬁ ed service personnel. Servicing is required when the apparatus has been dam aged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the ap pa ra tus has bee n exposed to rain or moisture, does not op er ate normally, or has been dropped.

Care and Maintenance

• Always use a soft cloth to clean the speaker and transmitter. Never use any product containing alcohol or other

solvents as they may damage the surface.

• Use caution when plugging the power transformers in an AC outlet to avoid the risk of electric shock.

• If the speaker are used outside on a deck or patio, make sure you take them indoors in the event of a rainstorm to

prevent possible damage.

• Do not operate or store the system in extreme temperatures (below 32ºF/0ºC and above 122ºF/50ºC).

LMR

DC IN

Tour of the Speaker

Speaker

Included Accessories

900MHz Wireless Transmitter

Front panel

Power and Pairing indicator shows the status

of the speaker.

Blue, slow blinking: The speaker is on but not paired or connected (like when you turn the speaker on for the ﬁrst time).

Blue, fast blinking: The speaker is in

Bluetooth pairing mode. See the Using Bluetooth Wireless section for more

information.

Solid blue: The speaker is paired with a Bluetooth-enabled device and ready to play audio.

Green, slow blinking: The speaker is on and in 900MHz mode, but not linked with the wireless transmitter.

Solid green: The speaker is linked with the 900MHz wireless transmitter and ready to play audio.

Rear panel

Bass Boost button turns the speaker’s bass

enhancement on and off.

On-Off / RF-BT turns the speaker on and off

(press and hold for four seconds). It also toggles between Bluetooth wireless and 900MHz wireless reception (press).

Scan-RF / Pair-BT scans for the 900MHz

transmitter’s signal in 900MHz mode (press). In Bluetooth wireless mode, press and hold this button for four seconds to begin pairing with your device.

Volume +/– buttons adjust the speaker’s volume

level

Powering the Speaker

3.5mm audio in cable

Model AWS5B3 Installation and Operation Manual

Portable Wireless Speaker

Bottom Panel

L/M/R switch determines if the speaker plays

sound in mono as a stand-alone speaker, or plays the left or right track in a stereo pair with an additional AWS5B3 when streaming audio with the 900MHz wireless transmitter

DC IN receives the small round end of the

included 9V 1200mA AC power adapter; remove the protective cover to insert the adapter

AUDIO IN connects directly to your MP3 player,

smartphone, or other portable audio device, using the 3.5mm audio in cable provided

Battery Compartment Cover (not shown)

remove to install 6 AA batteries

There are two options to power your wireless speaker: using the included AC power adapter or using 6 AA batteries (not included).

AC Power Adapters

1. Insert the small, round plug from the speaker AC power adapter into the DC IN jack on the bottom of the speaker.

2. Plug the other end of the speaker AC power adapter into any standard 120V AC wall outlet.

Note: Be sure to use the speaker AC power adapter rated 9V DC 1200 mA.

Warning: This product is water-resistant, not waterproof. Avoid prolonged exposure to wet

AA Batteries

1. Remove the battery compartment cover on the bottom of the speaker.

2. Insert six (6) AA batteries (not included) into the speaker following the polarity (”+” and “-”) as diagrammed inside the battery compartment.

3. Replace the battery compartment cover on the bottom of the speaker.

Note: Place the rubber cap in the speaker power input jack when using batteries.

DO NOT mix batteries with different chemistry types (for example, a zinc battery with an alkaline

battery).

DO NOT mix new and used batteries. DO NOT leave batteries installed in the product

when not in use for long periods. Always remove old, weak or worn-out batteries promptly and recycle or disp ose of the m in acco rdance wit h local and natio nal regul ations.

Tour of the Speaker

Included Accessories

900MHz Wireless Transmitter

SIGNAL indicator lights green when the audio is

present and the transmitter is broadcasting

POWER indicator lights when the transmitter is on

CHANNEL 1 2 3 lets you ﬁ nd the best

transmission frequency for your environment

DC IN jack receives the small round end of the

included 12V 200mA AC power adapter

AUDIO IN (R / L) connects to your sound source

using one of the connection options shown here

Powering the Speaker

3.5mm audio in cable

using Bluetooth Wireless

Using 900MHz Wireless

Pairing

Any Bluetooth-enabled device with A2DP SOURCE that you wish to stream audio to your speaker system must ﬁ rst be paired to the speaker. The process is simple, and in most cases the pairing process needs to be done only once.

To pair your Bluetooth-enabled device with the speaker:

1. Make sure your device’s Bluetooth is turned on. See the wireless and/or network settings menu on your device to check.

2. If the speaker isn’t already on, press and hold the On-Off / RF-BT button for four seconds to turn it on. You will hear a beep and the indicator light on the front of the speaker will start ﬂ ashing blue.

3. Press and hold the Scan-RF / Pair-BT button for four seconds to enter pairing mode. You will hear a beep and the indicator on the front of the speaker will start blinking faster.

4. Open the Bluetooth settings menu on your device. Select “AR SPEAKER” from the list of devices available (you might have to scan for devices). If your device asks for a password, enter “0000”.

5. A conﬁ rmation screen will appear on your device once the speaker and the device are successfully paired. The blue indicator turns solid blue to indicate successful connection. The speaker is now ready for you to stream audio from your device.

6. Start playing something on the device. You can control the speaker volume on the speaker itself, using the Vol +/– buttons

on the back of the speaker, or on your device, using its

volume controls.

Note: If you notice the sound from the speaker is distorted, turn down your device’s volume.

Note: These power units should be plugged in so

that they stay vertical or lie ﬂ at.

Back panel

DC IN

CHANNEL

1 2 3

R AUDIO L

Top panel

Streaming Audio With Bluetooth

Once you’ve paired and connected your device with the speaker, you can control music playback from the palm of your hand. Select your music, stop it, change songs and playlists, all right from your device’s screen.

To adjust volume: Press the Vol +/– buttons

on the back of the speaker.

To disconnect from the speaker: Either turn Bluetooth off on your device or choose “Disconnect” from the list of options in your device’s Bluetooth settings.

To reconnect with the speaker: Just turn the speaker on and wait a few seconds for the speaker to ﬁ nd and connect to your device. If the speaker still hasn’t found your device (which may happen if, for instance, another device has been connected after yours) make sure the speaker isn’t connected to another device currently. Then select the AWS5B3 from the list of Bluetooth connections available in your device’s Bluetooth menu to connect to it.

Powering the Transmitter

Connect the small, round plug from the transmitter AC power adapter to the transmitter’s DC IN jack. Plug the other end of the transmitter AC power adapter into any standard 120V AC wall outlet.

Note: Be sure to use the speaker AC power adapter

rated 12V DC 200 mA.

Note: There is no transmitter ON/OFF switch. The transmitter is designed to be left plugged

in and powered at all times. If you will not be using the AWS5B3 for an extended period of time, unplug the transmitter AC power adapter.

+ 2 hidden pages