
PACKING LIST
Acoustech X is
The
panels,\rhile
Packed with
card
tech
the
have occurled intransit" The responsibility for saJe
so any claims
vhich should
x
can be covered by tlle t-lrlee-year factory
The following items
dual amplifiers and associated circuitry:
Spare AGX-1-1/2 amp tuses fo!
4
-
Detachable AC line cord,
1
-
6
12-24 x 1-3/4" machine screws
-
Fifiy-foot special shielded cable
1
-
center or Acoustech tuner/control
The Acoustech X was in
other
the
two
the speake!
be returned to the
lor damage must
shipped
each
will
be
perfect
in three separate caltons, the
contain
panels
found in aplastic bag
UNPACKING THE ACOUSTECH
be
dual amplifiers
in
factory within thirty
large carton is
tie
varranty.
(packed
B+
(packed
for
connecting
center.
condition
made
by
vhen it left our factory, so any visible damage must
you
against them.
and associated
(30)
packed
in sma1l
in small
each amplifier to the
this
days of
in
93gL
plastic
plastic
X
lalgest
circuiiry.
operating manual and a warranty
purchase
ol the two cartons containing
bag),
bag), and
containing t]Ie speaker
so that this Acous-
Acoustech VI
control
delivery rests with the transportation company,
If
the cartons
pleserce
not
vait,
already
removinE
left,
If
tlere is no evidence of external damage,
1, To remove
standing
2.
its
3, Remove the
4. Remove one
5.
6. Unpack each of the ampllfier assemblles,
tfreir
as sembly,
(particularly
of the delivery man and inspecttie
note any
damage on the
corners) shov evidence of severe damage, open them in tie
the
delivery slip and make sure the delivery man signs it. If he has
call the transportation company
the equipment:
the
carton vill
Remove
present position.
Remove the
cartons that
the first fiUer
top
side
panels.
speaker
now
end Jiller.
filler,
you
do not crush the snap-on terminals
panels,
be in excess
piece you
contents with him, Il this is not
for instructions
follov
this
before
procedure
raise the carton to an
of six feet).
see, which extends the complete height
Take care when removing the assemblies from
opening
for opening the cartons and
upright
which are taped to one side of the
possible
tie cartons.
position
or if he can-
(the
height of the
of
the carton
in
7. Thoroughly
dealer
the factory
In
cartons
inspect all
(if
any case, save the cartons
\rill
be a
system was shipped from
the
if
the system
necessity" See Appendix for lepacking
pieces
was shipped from tie
for any visible
his stock) or notify t]Ie transportation company and
packing
and
damage. If damage is apparent, notify
factory.
you
matelial.
instructions"
If
have
to
move
the
your
equipment the

IMPORTANT
NOTICE
Whenever
deliYer
Unlike otler electrostatic
pover
you
turn on
their full
of the Aeoustech X is
power.
your
Acoustech Xsystem,
systems tlat are always on,
switched on and ofJ from its Acoustech
a minute may
eyen if the control center i6
required
be
cootr,ol center,
for the woofers to
off, tlle

General
SETTING
UP
The two amplifier
panels
differ only in
viewed from the front)
up,
the tweeters vill
tweeter in a
the
base
The tweeter is located
Assembly
1.
much easier to move
the wooden
the speaker,
For
2. Carefully
particular
ol each
Move
speaker
t}Ie speaker
frame, use a carpeted
panel:
each
place
assemblies
location
the
while on tie other it is on the right side.
then be at the outside
panel,
panel.
on this side.
panels
panels
the
speaker
the
facing upward.
3. Fold
back
just
enough of
complete base, You do not vant
attached,
4.
partialiy
assembly
but the
Place
into
should rest
plastic
will keep
the amplifier assembly
the recessed
on the floor
area in the
(black
of t}Ie tweeter.
look
to tie end
You vili find a serial number
as close to the area in which
when tie amplifier
area or
panel
plastic
the
the amplifier assembly to retain
the speaker cloth clean while
bottom
(Figure
boxes) are identical in all respects.
panel
one
floor,
stamped in one corner ol this area.
is
or
similar material on
face do{n. The
the speaker is wrapped
the
the cover should
panel.
edges
of
place
some
flat on
cover in which
(perforated
of the speaker
1).
On
of the system. To determine
the terminal strips located
assembly
towels
the
holes in
The two speaker
the tweeter
When the system is correctly set
they vill be
not
attaehed). To avoid scratching
plastic
the
panels
The
is
on the left side
location
the
at the bottom rear of
used
possible
as
the
floot, under
terminal strip
expose
to
when the assembly is
are on the floor.
lacing
be
rear feet of the
of the
(it
\pill
upward)
amplilier
(as
is
be
the
There
5,
from left
These
tJIe fastener
to right, they appear
leads must
6. After all
'rsnap"),
test all leads
?. Dress
to make
opexation:
sure they are
8. Tip the
lover
screw
speaker
enough
all is
fro-!ll- edge of
holes so that
panel
to check
vell,
are seven
leads
coming
in this order:
be connected to the terminal strip connectors on
at tie end of each lead into
leads
the
the
by tugging
leads
pulledout
have
been
gently
as shown iB Figure 1, Gentiy
all the way, as
amplifier assembly into
the chassis, sothatthe
machine
the
base. Do not tightgn dovn
that a1l seven leads
place
the
amplifier assembly
screws
out of
the amplifier
assembly.
1. heavy red
2. heavy red
yellow
3.
green
4.
or blue
5, black
6. red
?. heavy red
place
connected
to make sure that the lasteners
are
over its opposite number
(the
evidence of
tug the
you
place
chassis
(three
against
on each side)
lhe screvs
still
tightly
back
on the speaker
do not
is
want to snap loose a lead in
the base of the
raised into an erect
yet.
Instead,
snapped
leads
can be drolped inio
onto
panel
Looking dovn,
the speaker
on the connector striq.
lirm
a
connection is an audible
panel
from above,
by snapping
are securely seaied.
from
paneis
amplifier
the
by
position.
assembly
the
pivoting
Liile u!
hoies
the
fo
on the
the six
owing
in the
tilt back the amplifier assembly
3.
(Figure
2), If
speal<er
the
as in Figure
panel