ACORN SAFETY S1310, S1320, S1330, S1340, S2310 Installation Manual

ACORN SAFETY

P.O. BOX 3527
CITY OF INDUSTRY, CA 91744-0527

UNITED STATES OF AMERICA

WWW.ACORNSAFETY.COM

INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS

COMBINATION STATIONS

Models: S1310, S1320, S1330, S1340, S2310,S2330, S2340

TECHNICAL ASSISTANCE TOLL FREE TELEPHONE NUMBER

1.800.591.9360

TECHNICAL ASSISTANCE FAX: [phone]

NOTES TO THE INSTALLER:

1. Please leave this documentation with the owner of the fixture when finished.

2. Please read this entire booklet before beginning the installation.

3. Check your installation for compliance with plumbing, electrical, ANSI Z358.1 and
other applicable codes.

LIMITED WARRANTY

UNITED STATES AND CANADA

Acorn Safety warrants that its products are free from defects in material or workmanship under normal use and
service for a period of one year from date of shipment or 18 months after the date of shipment from factory ,
whichever comes first. Acorn's liability under this warranty shall be discharged solely by replacement of repair of
defective material, provided Acorn is notified in writing within one year from date of shipment, F.O.B. Industry,
California.

This warranty does not cover installation or labor charges and does not apply to materials, which have been
damaged by other causes such as mishandling or improper care or abnormal use. The repair or replacement of the
defective materials shall constitute the sole remedy of the Buyer and the sole remedy of Acorn under this warranty.
Acorn shall not be liable under any circumstances for incidental, consequential or direct charges caused by defects in
materials, or any delay in the repair or replacement thereof. This warranty is in lieu of all other warranties expressed
or implied. Product maintenance instructions are issued with each unit and disregard or non-compliance with these
instructions will constitute an abnormal use condition and void the warranty. Stainless steel must be protected on job
sites during construction and must be properly maintained after the water has been introduced into the safety product
or Acorn's warranty is void.

Acorn Safety a division of Acorn Engineering Company™

Manual #7109-250-001

Revised: 01/08/2013

Installation & Operation Manual

PRELIMINARY STEPS

1. Read the installation instructions prior to beginning the installation.

2. Separate parts from packaging and verify all necessary parts are accounted for and undamaged. Obtain missing or
damaged parts from Acorn Safety prior to beginning installation.

3. Flush water supply lines prior to installation. This will remove unwanted debris from the lines and prevent unwanted
blockages in the safety equipment.

4. In order to comply with ANSI Z358.1, the safety equipment must be inspected periodically. An inspection tag is provided for
documentation purposes.

5. all employees at risk of contamination should be informed and trained in the use of this and any other safety equipment. The
signage provided should be posted appropriately in close proximity to this equipment.

ROUGH-IN

1

Ø 7

Ø 9

1

"

8

FLANGE MT'G

DETAIL

"

2

(191)

3
8

(10)

4X MT'G

HOLES

"

1

23

2

(595)

"

1

1

" NPT

4

SUPPLY PLUGGED

5

10

8

(270)

1

1

" NPT

4

SUPPLY

3

84

"

8

(2144)

3

65

"

8

(1659)

"

5

41

8

(1056)

"

5

31

"

8

(799)

1

10

"

4

(260)

1

1

" NPT

4

WASTE

8"

(203)

5

62

8

(1591)

"

89"

(2261)

Acorn Safety a division of Acorn Engineering Company™

Manual #7109-250-001

Page 2 of 5

Revised: 01/08/2013