Acorn Engineering TSH-24, KF24 User Manual
Terrazzo-Ware™ Mop Sink - Standard Height (12") Series
TSH-24-KF24
Fixture May Show Some Available Options
Please visit www.acorneng.com for most current specifications.
Terrazzo Standard Height Mop Sink
Mop Sink is an attractive, durable fixture designed to be easy to install and maintain. ACORN
Terrazzo-Ware™ precast mop sinks provide flexibility in configuration and size as required by the design
of the building and the specific installation. Custom sizes and colors are also available.
Construction is one piece, precast terrazzo composed of marble chips cast in Portland cement to provide
a compressive strength of at least 3,000 PSI seven days after casting. The mop sink surface is ground
smooth and sealed to provide years of service.
Integral Drain is supplied with a removable, stainless steel grid strainer and provides for an inside
caulked connection to a 3" pipe. The mop sink has coved corners and is pitched to the drain outlet to
provide positive drainage. A beehive dome strainer is optionally available.
Shoulders come standard without caps exposing the natural terrazzo finish. Optionally, they may be
capped with stainless steel for protection.
Tiling Flanges made of galvanized steel are provided loose as an easy to install accessory when flexibility
and simplicity are desired. As an alternative, factory installed galvanized steel tiling flanges extending at
least 1" above the shoulder can be specified.
Accessories to complement and complete the installation of the mop sink include:
• chrome finish faucets
• 36" hose to reduce splashing with wall hanger to support the hose
• mop hanger for easy storage of the mop over the sink
• rubber drain gaskets for easy installation of the fixture
• stainless steel wall guards to protect sensitive walls from splashing water
• tiling flanges for simple, flexible field installation
GUIDE SPECIFICATION
Provide and install an ACORN Standard Height Mop Sink (specify model number and options). Mop
Sink shall be made of precast terrazzo to produce a compressive strength of not less than 3,000 PSI seven
days after casting. All exposed surfaces shall be ground smooth and sealed. No air holes or pits shall be
allowed on the finished surface. Sink shall have coved corners and be pitched to the outlet for positive
drainage. Integral drain shall have a stainless steel strainer and provide for an inside caulked connection
to a 3" pipe. The manufacturer will provide to the installer the necessary installation instructions.
Page 1
Acorn Engineering Company • 15125 Proctor Avenue • P.O. Box 3527 • City of Industry, CA 91744-0527 U.S.A.
Tel: (800) 488-8999 • (626) 336-4561 • Fax: (626) 961-2200 • www.acorneng.com • E-mail: info@acorneng.com
T.MSSH
Revised: 12/13/12
Terrazzo-Ware™: Mop Sink-Standard Height (12") Series
BASE MODEL, SIZE & TYPE
o TSH-24 24" Square Terrazzo Standard Height
Mop Sink
o TSH-32 32" Square Terrazzo Standard Height
Mop Sink
o TSH-36 36" Square Terrazzo Standard Height
Mop Sink
o TSH-3624 36" x 24" Rectangular Terrazzo
Standard Height Mop Sink
SUFFIX OPTIONS
o - BDS Beehive Dome Strainer
o - OC Optional Colors (contact factory)
o - SSC Stainless Steel Cap
TILING FLANGES (factory installed)
o - TF1 Tiling Flange, Rear Side
o - TF2 Tiling Flange, Two Adjacent Sides
Specify: q Right & Rear q Left & Rear
o - TF3 Tiling Flange, Three Sides
Please visit www.acorneng.com
for most current specifications.
ACCESSORIES
o KDG3 Rubber Drain Gasket for 3" Waste Pipe
o KDG32 Rubber Drain Gasket Reducer
for 2" Waste Pipe
o KF Tiling Flange(s) (Shipped Loose; N/A With -TF Options)
Specify length(s):
o 24" Qty:______ o 32"Qty:_____
o 36" Qty:______
o KFC Faucet, Chrome Finish (H & C)
o KH36 Hose 36" Long with Wall Hanger
o KMH Mop Hanger with 3 Grips
on a Stainless Steel Bracket
o KWG Wall Guard (Shipped Loose)
Specify number of sides:
o 1 Side o 2 Sides o 3 Sides
Specify length(s):
o 24" Qty:_____ o 32" Qty:_______
o 36" Qty:_____
o LB Lint Basket/Strainer
Dimensions are subject to manufacturer’s tolerance of plus or minus 1/4" and change without notice. Acorn assumes no responsibility for use of void or superseded data. © Copyright 2007 Acorn Engineering Company
Model No. & Option___________________________
Quantity____________________________________
Tel: (800) 488-8999 • (626) 336-4561 • Fax: (626) 961-2200 • www.acorneng.com • E-mail: info@acorneng.com
Important: Installation instructions and current rough-in are furnished with each fixture. Do not rough in without certified dimensions.
Selection Summary
Approved for Manufacturing
Company__________________Title______________
Signature_________________ Date______________
Page 2
Acorn Engineering Company • 15125 Proctor Avenue • P.O. Box 3527 • City of Industry, CA 91744-0527 U.S.A.
T.MSSH
Revised: 12/13/12
Loading...