Acnodes KC 802 User Manual

User Manual
KC802/1602/3202: 1U rackmount Combo Cat6 KVM switch 8/16/32-port RJ45 with 2 user console
KC802/1602/3202
14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc. All righ ts reserved. Product descripti on and product speci ficat ions are subj ect to change w ith out n oti ce. F or lates t product inform ati on, ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
KC802/1602/3202
Legal Information
First English p rinting , October 2002 Information in this document has been carefully checked for accuracy; however, no guarantee is g iven to the correctness of th e contents. The info rmation in this document is subject to change without no tice. We are not liable for any injury or loss that results from the use of this equipment.
Safety Instructions Please read all of these instructions carefully before you use the device. Save this manual for future reference.
¦ Unplug equipment bef ore cleaning. Do n’t use liquid or spray detergent; use a moist cloth. ¦ Kee p equipment away from excessive humidity and heat. Prefe rably, keep it in an air-conditioned e nvironm ent with
tempe ratu res not exceeding 40º Celsius (104º Fahrenheit).
¦ Wh en installing , place the eq uipment on a sturdy, level surface to pre vent it from accidentally falling and causing dam
age to other equipment or injury to persons nearby.
¦ Wh en the equipment is in an open position, do not cover, block or in any way obstruct the gap bet ween it and the
power supply. Proper air convection is necessary to keep it from overheating. ¦ Arrange the equipment’s power cord in such a way that o thers won’t trip or fall over it. ¦ If y ou are using a po wer cord that didn’t ship with th e equipment, ensure that it is rated for the voltage and current
lab eled o n the equipment’s electrical ratings label. The voltage rating on the cord sho uld be higher than the one listed
on the equipment’s ratings label. ¦ Observe all precautions and warnings attached to t he equipment. ¦ If you don’t inte nd on using t he equipment for a long time, disconnect it from the power outlet to prevent being dam
aged by transient over-voltage. ¦ Kee p all liquids away from the equipment to minimize the risk of accidental spillage. Liquid spilled on to the power
supply or on other hardware may cause damage, fire or electrical sho ck. ¦ Only qualified se rvice personnel should open the chassis. Opening it yourself could damage the equipme nt and invali
date its wa rranty. ¦ If any part of the equipment becomes damaged or stops functioning, have it checked by qualified service personnel.
What the w arranty does not cover
¦ Any product, on which the serial number has been defaced, modif ied or removed. ¦ Damage, deterioration or malfunction resulting from :
? Accident, misuse, neglect, fire, water, lightn ing, or othe r acts of nature, unauthorized product modifica tion, or
failure to follow instructions supplied with the product. ? Repair or at tempted repair by anyone not authorized by us. ? Any damag e of the product due t o shipment. ? Removal or insta llation of the product. ? Causes external to the product, su ch as electric power fluctuation or failure. ? Use of sup plies o r parts not meeting our specifications. ? Normal wear and tear. ? Any other causes which does not relate to a product defect.
¦ Removal, installation, and set-up service charges.
Regulatory Notices Federal Communic ations Commission (FCC)
This equipment has been tested and found t o com ply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential instal- lation. Any changes or modifications made to t his equipment may void the user’s authority to ope rate this equipment. This equipment generates, uses, and can ra diate radio freq uency energy and, if not installed a nd used in a ccorda nce with the instructions, may cause ha rmful interference to radio communications. However, there is no guarantee that int erferen ce will not occur in a particular installati on. If this equipment does cause harmful interference to radio or television reception, which can be determined by tu rning the e quipme nt off and on, the user is encouraged to try to correct the inte rference by one or more of the foll owing measures: ¦ Re-position or relocat e the receiving antenna. ¦ Inc rease the separation between the equipment and receiver. ¦ Connect the equipmen t into an outlet on a circuit different from that to w hich the receiver is connected.
1U Rackmount Combo Cat6 KVM switch
14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc. All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns are subj ect to change w ith out n oti ce. F or lates t product inform ati on, ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
KC802/1602/3202
Contents
< Part 1 > Combo Cat6 2-console KVM
KC802 KC1602 KC3202
1.1 Package contents
1.2 KVM port & Cat6 dongle connection
1.3 Remote & Local console connection
1.4 KVM Cascade
1.5 Specifications
P.1 P.2 - 3 P.4 - 5 P.6 P.7
< Part 2 > Usage
2.1 KVM Button
2.2 Password
2.3 KVM OSD
2.4 KVM Hotkey & Remote Console Hotkey
2.5 DC power 12V, 24V, 48V Input
P.8 P.9 P.10 P.11 P.12
14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc. All righ ts reserved. Product descripti on and product speci ficat ions are subj ect to change w ith out n oti ce. F or lates t product inform ati on, ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
KC802/1602/3202
Before Installation
¦ It is very important to mount the equipment in a suitable cabinet or on a stable surface. ¦ Make sure the place has a good ventilation, is out of direct sunlight, away from sources of excessive
dust, dirt, heat, water, moisture and vibration.
Unpacking
The equipment comes with the standard parts shown in package content. Check and make sure they are included and in good condition. If anything is missing, or damaged, contact the supplier immediatel y.
Installation for standalone KVM
Screw A: 2 pcs Screw B: 8 pcs
M3.2 x 4.5 m m M4 x 10 mm
¦ Install each bracket using screws
A
B provided shown in Figure 1.
¦ Fix the KVM into the rack
Figure 1.
1U Rackmount Combo Cat6 KVM switch
14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc. All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns are subj ect to change w ith out n oti ce. F or lates t product inform ati on, ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Part 1. Combo Cat6 2-console KVM
< 1.1 > Package Content
Combo Cat6 2-console KVM
KC802 / KC1602 / KC3202
KVM unit
Combo KVM unit x 1
Mounting set w/ bracket & screws x 1
Power cord ( for KVM ) x 1
+ +
X 1 set
Receiver b ox
for remote con so le
Receiver’s power adapter
w/ power cord
CE-6 KVM cable
for receiver box
KC802/1602/3202
14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc. All righ ts reserved. Product descripti on and product speci ficat ions are subj ect to change w ith out n oti ce. F or lates t product inform ati on, ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Loading...
+ 11 hidden pages