Acnodes FES 2213 User Manual

FES2213

User Manual

FES2213: Fanless Embedded System Atom N2600 Dual Core 1.6GHz Processor

14628 Central Ave, Chin o, CA 91710 tel: 909.597.7588, fax:909.597.1939

Fanless Embedded System

© Copyrigh t 2013 Acnodes, Inc. All rights reserved. Product descripti on and product specifi cations are subj ect to chan ge without noti ce. For latest product informati on, please visit Acnodes’ we b site at www.acnodes.c om.

This publi cati on c ontains inform ation that is prot ected by copyright. N o part of it m ay be reproduced i n any form or by any m eans or used to make any transform ation/adaptation without the prior written permission from the copyr ight holde rs. The manufacturer reserves the right to revise this publication and m ake changes to its contents at any time, w ithout obl igation to noti fy any person or entity of such revisions or changes.

Trademarks

Al l tradem arks and registered trademarks of products appearing in this m anual are the properties of their respective holders.

Notice:

1. The chan ges o r modifica tion s n ot expressly a ppro ved by th e p arty r espo nsible fo r compliance cou ld void th e user ’s auth ority

to op erate t he eq uipment .

2. Shielded int erfa ce ca bles must be used in or de r to comply wit h t he emission limits.

Static Electricity Precautions

It is quite easy to inadvertently dam age the system board, c omponents or devices e ven before i nstal ling them i n your system unit. Static electri cal discharg e can dam age computer com ponents wi thout causing any signs of physi cal dam age . You must take extra care in handl ing them to ensure against el ectrostatic bui ld up.

1. To prevent electrostatic bui ld up, le ave the system board i n i ts anti-static bag unti l you are ready to install it.

2. Wear an antistatic wrist st rap.

3. Do all preparation w ork on a stati c-free surface.

4. Hold the device only by its edges. Be careful not to touch any of the components, contac ts or connections.

5. Avoi d touching the pins or contacting all m odul es and connectors. Hold modules or connectors by the ir ends.

Impo rt ant: Elect rost atic d ischa rge (ESD) can damage you r p rocessor, disk dr ive an d ot her compo nents. Perform t he up grade instru ct ion pr ocedures describ ed at an ESD wor kstation on ly. If such a sta tion is no t availab le, yo u can provide some ESD protection by wear in g a n ant istatic wrist st rap and attaching it to a met al part of the system chassis. If a wr ist strap is una vailab le, es tab lish an d maintain contact with the syst em chassis th roug hout any p rocedures req uiring ESD protection .

FES2213

Safety Measures

Fanless Embedded System

To avoid dam age to the system :

• Use the correct A C input vol tage range to reduce the risk of ele ctric shock.

• Unplug the power cord before rem oving the system chassis cover for install ati on or servi cing. After

instal lation or servicing, cover the system chassis bef ore plugging the power cord.

Batte ry:

• Dange r of expl osion if battery incorrectly replaced.

• Repl ac e only w ith the same or e quival ent type re com mend by the manufacture r.

• Dispose of used batteries according to l ocal ordinance.

Warranty

1. Warranty does not cover dam ages or fai lures caused by m isuse of the product, inabili ty to use the

product, unauthorized replacem ent or any kind of alterations of components and product specif ications.

2. The warranty i s voided if the product has been exposed to physi cal abuse , improper instal lation, a ny

kind of modific ation, acc idents or unauthorized repair of the product.

3. Unl ess otherwise instructed in this user m anual, the user m ay not, under any ci rcum stances, attem pt to

perform servi ce , adjustm ents or repairs on the product him se lf, whether the product is sti ll covered by warranty or not. It must be returned to the place i t was purchased at, the fa ctory or an authorized se rvic e agency for any re pai r work.

4. We w il l not be l iabl e for any indi re ct, spe cial, incidental or conseque nt damages to the product that has

be en m odif ied or alte red.

14628 Central Ave, Chin o, CA 91710 tel: 909.597.7588, fax:909.597.1939

FES2213

Copyright ........................................................................ .......................................... 2

Tradem arks ............................................................................................................... 2

Static Electr icity P recautions .................................................................................... 2

Safety Me asures ....................................................................................................... 3

Warranty ................................................................................................................... 3

Chapter 1: Introduction

1-1 Overvi ew.............................................................................................................. 5

1-2 Product Specification........................................................................................... 6

1-3 System Block Diagram......................................................................................... 8

1-4 Mechani cal D iagram ........................................................................................... 9

1-5 Front, Top, & Bottom Panel I/O………................................................................... 10

Chapter 2: Pin Definition & Jumper Settings

2-1 Front panel P in Definition…………………………………………………….............…………… 11

2-2 Front, Top, and Bottom Panel P in Definition…………………………………….…………… 11 2-3 Internal Pin Definition & Jum per Settings………………………………………………………. 12

2-3.1 M B Top V iew………………………………….……………………………………………….…. 12 2-3.2 M B Bottom V iew………………………………….………… …………………………………. 12 2-3.3 M B P in Definition…………………………….…………………………………………………. 13

2-3.4 Jum per Setting.……………………………….…………………………………………………. 17 Chapter 3: BIOS Setup 3-1 Introduction……………………….…………………………………………………………………………. 27 3-2 Enteri ng BIO S…………………………………………………………………………………….…………… 28

3-2.1 M ai n Setup…….……….…..………………………………………………………………….…… 28

3-2.2 A dvanced BIOS Features………………..………………………………………….………… 29

3-2.3 Chipset.…………………………………………………………………………………….………… 39

3-2.4 Boot Se tting………………………………………………………………………………………… 43

3-2.5 Securi ty Setup.…………………….……………………………………………………………… 44

3-2.6 Save & Exit…...…………………….……………………………………………………………… 45 Chapter 4 : Software Support

4-1 Software Appl ications………..…………………………………………………………………………. 47 4-2 Instal lation Guide…..………………………………………………………………………………… …… 49

Appendix A:

WatchDog T imer Sam ple Code…………………..………………………………………………… 56

GP IO Sample Code………………………………… …..………………………………………………… 58

14628 Central Ave, Chin o, CA 91710 tel: 909.597.7588, fax:909.597.1939

Fanless Embedded System

Table of Contents

© Copyrigh t 2013 Acnodes, Inc. All ri ghts reserved . Produ ct descri pti on an d produ ct specificati ons are subj ect to chan ge without noti ce. For latest product informati on, please visit Acnodes’ we b site at www.acnodes.c om.

FES2213

Fanless Embedded System

Chapter 1: Intr

1-1 Overv iew

oduction

Acnodes’ FE S2213 is the latest released model with outstanding size along with reliable functionality embedded system in low power and low operating temperature.

FES2213is equipped with Atom N2600 Dual-core 1.6 GHz processor with supported by the NM10 South Bridge chipset. I t pro vides to r each t he maximum memory size up to 4 GB DDR 3- 800 with one SODIMM. FES2213 supports for VGA display function in 1920 x 1200 ( 1080p) resolution while as 18/ 24b-bit 1366 x 768 LVDS features reserved internally.

In order to meet t he network stability, FES2213uses one 82583V 100/ 1000 Mbps LAN wit h Wake-On LAN & DMI 2500 VDC isolation protected. It provides 2.5” SATA HDD and 1Mini-PCI-E mSATA for fulfilling the storage. FES2213enables for expansion flexibility for one half size of Mini-PCI-E expansion slot even with its easy- to-carry and mini size of W66.5mm x H130mm x D100mm. GPI O feature is reserved internally by t he SMSCSCH3114 controller, which provides 8bit programming GPI O with TTL level. The system designed with two DB-9 for supporting for RS-232 interface, and each port supports for 16 Byte FIFO (optional 5V DC output). I t also provides a software programming Watchdog (WDT) wit h timer range from 1 to 255 seconds.

The power supply is capable for DC power input of 12V or 24V (optional). The power consumption is able to r each up to 10W in maximum. The construction of FES2213is designed as DIN Rail Heavy-duty steel embedded platform. The system is valuable for all t he embedded applications, and also well support with the Window 7, Windows XP and Linux Operation system.

FES2213is the latest embedded system from Acnodes’ wit h low power consumption, low operating temperature, and particularly with its extraordinary size of total weight of 1.5kg. Acnodes is proud to announce and welcome you to experience our mini -sized but stable functionalized FES2213.

14628 Central Ave, Chin o, CA 91710 tel: 909.597.7588, fax:909.597.1939

1-2 Pr

oduct

ecification

rocessor & Chipset

 Sup port Atom N2600 Dual-core 1.6 GHz Processo r  NM10 Sou th Brid ge Chip set

Graphic Engine

 Graphic core 400 Mhz  Sup port AVC/ H.264, VC1/ WMV9, MPEG2 HW engine  HD CP 1.3 ans PAVP 1.1C content protection su pport  Sup port Microsoft DXVA 2.0 and Overlay DD  MS COPP an d PVP-OPM supp ort  Enablin g Key ISVs-Corel, Cyb erLink, ArcSoft  Sup ports OpenGL 3.0 and Microsoft DirectX 9

Display

 VGA supp ort 1920 x 1200 (1080P) resolution  Internal reserved 18/24bit 1366 x 768 LVD S feature

ystem Memory

 1 SODIMM Socket, up to 4GB 800 MHz DDR3 Memo ry

Function

BIOS

 AMI EFI BIOS. Support Power On after Power Failu re

xpansion

 1 half size Mini-PCI-E expansio n slot

thernet

 1 8253V 100/1000 Mbps L AN with Wake-On LAN & D MI 2500VD C isolation protection

Disk Drive Storage

 2.5” SATA HDD  1 Mini-PCI-E mSATA

Internal Reserved Audio Feature

 Audio feature, ALC892 HD Codec sup port  Audio Mic-in, Line-Out, Line-In feature

Watchdog Time

 Programmab le WDT from 1 to 255 seconds/minutes  Setup by software

Power Management

 Full ACPI 3.0  Sup port S1, S3, S4, S5  Sup port Wake on LAN

Internal Reserved GPIO Feature

 Con troller: SMSC SCH3114  8 bit Programmin g GPIO with TTL level

RS-232

 2 DB-9 for RS-232 with auto -flow control

Each por t support 16 Byte FI FO, optional 5V DC outpu t

Front

 Screw-Lock DC power input connector  2 male DB-9 for 2 RS-232  DB-15 VGA disp lay interface  2 USB, 1 RJ-45 100/1000 Mbit L AN con nector  Power, HDD led, Power button  Reserved 2 DB-9/15 (top & bottom p anel) for optional expansion

Internal

 Audio Mic-in, Line-o ut, Line-in  18/24 bit LVDS  8 bit GPIO

Those reserved featu re may optio nal sup port by request

Power Supply

 DC 12V inp ut o r op tional DC 24V inp ut.  24VDC/ 0.85A, 12VDC/1.7A, AT/ATX power type  Power ad apter : AC to DC , DC 12V/5A 60W ( Optional )

Power

 Typ ical Power Consump tion: 7W  Maximum Power Consu mption: 10W

Supports

Panel Extend I/O Ports

Reserved Feature

Consumption

(with HDD)

Environment

 Operation Temperature:

- With extend temperature HDD: -20°C~45°C

- With extend temperature SSD: -20°C~60°C

 Storage Temp erature: -20°C~80°C  Relative Humidity: 10%~90% (Non-condensin g)

Mechanical

 Dimension W x H x D : 66.5mm x 130 mm x 100mm  Moun ting: Din Rail mount  Con struction: DIN Rail Heavy-Duty Steel Emb edded Platform  Weight (Net/ Gross): 1.5KG / 2.2KG

Certification

 CE/FCC Class A

Supports

 Windows 7, Win XP, Lin ux

1-3 System Block Diagram

FES

2213

1-4 Mechanical Diagrams

FES

2213

1-5 Fr

ont I/O

ont

Panel

Top &

Bottom

Panel

Chapter

Def initi on

Definition

DCD 2 RX

3 TX 4 DTR

GND 6 DSR

RTS 8 CTS 9 RI

Definition

D -

3 D+

G ND

2-1 Fr

2: Pin Definition

ont

Panel Pin Definition

1. Power Switch

2. LAN port

3. Two RS-232 ports (COM1 & COM2)

4. Two USB por ts

& Jumper Settings

5. Power & HDD ON/Off LED

- Power LED indicator would li ght when power is on.

- HDD LED indicator for hard disk access is an active low signal.

2-2 Top &

Bottom

Panel Pin Definition

1. One DR-9 reser ved for Top & Bottom panel as optional expansion.

2-3 Internal

2-3.1 Main Board Top View

Pin Definition & Ju mper Settings

2-3.2 Main Board Bottom V iew

2-3.3 Main Board Pin Definition

1. Battery Connector [refer to BH1] MIO-2261 supports Lithium 3V/210 mAH CR2 032 battery with w ire via batte ry connector (BH1).

Note: How to clear CMOS: (Must fol low below steps)

(1) Turn off system power (2) Unpl ug CR2032 battery cable on BH1

(3) Waiting for 15se c or short BH1 pin1 -2 (4) Connect battery cable on BH1 (5) Turn on system power

2. 12 V Power Input Connector [refer to CN 1]

Main power connector supports single 12V input , and there is an optional choice of DC/ Jack (CN2, co-layout with 2pin power connector) .

3. DDRIII SODIM M Socket [refer to CN 3]

One 204-pin/ H9.2 mm DDRIUII DIMM socket supports DDR3 800 MHz (N26 00)/ 106 6 MHz (N2800 ) up to 4GB.

4. GPIO (General Purpose Input Output) [refer to CN4]

The board supports 8-bit GPIO ( 5V tolerance) through GPIO pin heade r. The 8 digital inputs and outputs can be programmed to read or control devices, wi th each input or output defined.

5. VGA/ LVDS Interface Connections [refer to CN5 a nd CN 18]

The MIO-2261’s VGA interface can drive conventional CRT displays and is capable of driving a wide range of flat panel displays, including passive LCD and active LCD displays. The board has t wo connectors to support these displays: one for standard CRT VGA m oni tors and one for LVDS type LCD panels.

CRT display connector [refer to CN 5]

The CRT display 1 5pins connector is a rear I/O connector on coastline used for conventional CRT displays. Resolution: up to 1 920 x 12 00 (WUXGA).

LVDS LCD panel connector [refer to CN 18]

The board supports single channel 18/24 -bit LVDS LCD pane l displ ays via 14*1pin wafer box. Resoluti on: up to 1366 x 768 ( WXGA).

6. mSATA Connector [refe r to CN6]

MIO-226 0 provides a mini-P CIe socket which integrates USB and SATAII signals, supports either mSATA or USB interface modules.

7. SATA Connector [refer to CN 7]

MIO-226 1 features one high perform ance Se rial ATA interfaces. Data transfer rates up to 300 MB/s enabling very fast data and fi le transfer, and independent DMA operation on two ports.

8. M ini PCIe Connector [refer to CN8 ]

MIIO-2261 supports a half size mini PCI2 slot. PCI Express Mini Card (also known as Mini PCI Express, Mini PCI2, and M ini PCI-E) is a repl acem ent for the Mini P CI form factor based on P CI Express. It is developed by the PCI-SIG. The host device supports both PCI Express and USB 2.0 connectivity.

9. USB Connectors [refer to CN9 and CN 10]

The board provides four USB (Universal Se rial Bus) ports, two are rear I/O on coastline ( CN9); and the other two are internal USB ports ( CN10) . These gives complete Plug and Pl ay, and hot attach/ detach for up to 127 external devices. The USB interfaces comply with USB specification Rev 2.0 which support 480 Mbps transfer rate and are fuse protected.

10. COM Port Connectors [refe r to CN11]

MIO-226 1 provides 2 x RS-232 serial ports in 10* 2pi n pin header. It provides connections for serial devices or a com munication network. The pin assignments for the COM port connector can be found in Jumper Setting.

11. SMBus Connector [refer to CN1 2]

MIO-226 1 provides SM Bus connector for customer connection to SM Bus protocol em bedded device. It can be configured to I²C by customer’s request.

12. Front Panel Connector [refer to CN13]

MIO-226 1 integrates below functi ons as front panel 6pin connector. Power Button Supports powe r on/off button in ATX mode. Reset If you install a reset switch, it should be an open si ngle pole switch. M omentarily pressing the

switch will acti vate a reset. Power LED Power LED indi cator would light when power is on. HDD LED HDD LED indicator for hard disk access is an active low signal.

13. Gigabit Ethernet Connector [refer to CN14] MIO-226 1 uses Intel®82583 C Ethernet chip (10/ 100/ 1000 Mbps) l ined to dedicat ed PCI2 x 1 lane via RJ-45 connector.

14. High De finition Audio Interface [refer to CN 15]

MIO-226 1 provides one 5x 2 pin box header for audio device. It can support high definition audio stereo by customized audio module that has codec onboard.

15. Front Panel Conne ctor [refer to CN13]

MIO-226 1 supports MIO2 connector to extend flexible I/Os. Interface 2 x USB 2.0, 2 x P CIe x 1, LPC, HD Audio line-out, SMBus, DP (or HDMI, supported by request), 5 Vsb/ 12 Vsb power. Total peripheral power supply output 5V @ 3A for CPU board and MI/O Extension module totally, 1 2V @ 2A for M I/O Extension module.

16. Inverter Power/ Internal SATA Power Connector [refer to CN17]

The LCD inve rter is connected to CN17 via a 5-pin connector to provide +5V/ +12V power to the LCD display, and 5 V powe r can be provided for 2.5” SATA HDD via CN17. SATA powe r’s current is only sufficient for 2.5” HDD, and LVDS inverter ’s cur rent is 5V @ less than 1A, 12V @500mA.

2-3.4 Jum per Settings

Setting

Function

(

1-2)

＋5V

(3-4) (default)

＋3.3

(5-6) (default)

Auto Power On

PIN N ame

1 ＋12V

2 GND

PIN N ame

1 ＋VIN

2 GND

1. LCD Power/ Auto Power ON [refer to J1]

2. 1 2V Powe r Input [refer to CN1 ]

3. D C JACK (by request) [refer to CN 2]

4. D DR3 SO-DIMM [refer to CN3 ]

5 . GPIO [refer to CN4]

PIN Name

＋5V

2 GPIO4

3 GPIO0

4 GPIO5

5 GPIO1

6 GPIO6

7 GPIO2

8 GPIO7

9 GPIO3

10 GND

PIN Name

1 RED

2 GREEN

3 BLUE

4 NC

5 GND

6 GND

7 GND

8 GND

9 NC

10 GND

11 NC

12 DDAT

13 HSYNC

14 VSYNC

15 DCLK

6 . VGA [refer to CN5 ]

7 . mSATA [refer to CN 6]

PIN Name

1 NC

27 GND

＋3.3

＋1.5V

3 NC

29 GND

4 GN

SMB_CLK

5 NC

A－

＋1.5

SMB_DAT

7 NC

33 A＋

8 NC

34 GND

9 GND

35 GND

10 NC

USB

D－

11 NC

37 GND

12 NC

38 USB

D＋

13 NC

＋3.3V

14 NC

40 GND

15 GND

41 ＋3.3V

16 NC

42 NC

17 NC

43 NC

18 GND

44 NC

19 NC

45 NC

20 NC

46 NC

21 GND

47 NC

22 NC

＋1.5V

23 B＋

49 NC

24 ＋3.3

50 GND

B－

51 NC

26 GND

52 ＋3.3V

+ 39 hidden pages

Acnodes FES 2213 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual