Page 1
APW 5170
17” Industrial Panel Mount Widescreen LCD
User Manual
APW5170: 17” industrial panel mount widescreen LCD monitor
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All righ ts reserved. Product descripti on and product speci ficat ions
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 2
APW 5170
Legal Information
First English printing, Oc tober 2002
Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the
contents. The information in this document is subject to change wi thout notice. We are not liable for any injury or loss that results from
the use of this equipment.
Safety Instructions
Please read all of these instructions carefully before you use the device. Save this manual for future reference.
¦ Unplug equipment before clean ing. Don’t use liquid or spray detergent; use a moist cloth.
¦ Keep equipment away from excessive humidity and heat. Preferably, keep it in an air-conditioned environment with
temperatures not exceeding 40º Celsius (104º Fahrenheit).
¦ When installing, place the equipment on a sturdy, level surface to prevent it from acc identally falling and causing dam
age to other equipment or injury to persons nearb y.
¦ When the equipment is in an open position, do not c over, block or in any way obstruct the gap between it and the
power supply. Proper air convection is necessary to keep it from overheating.
¦ Arrange the equipment’s power cord in such a way that others won’t trip or fall over it.
¦ If you are using a power cord that didn’t ship with the e quipment, ensure that it is rated for the voltage and current
labeled on the equipment’s elec trical ratings label. The voltage rating on the cord should be higher than the one listed
on the equipment’s ratings label.
¦ Observe all precautions and wa rnings attached to the equipment.
¦ If you don’t intend on using the equipment for a long time, disconnect it from the power outlet to prevent being dam
aged by transient over-voltage.
¦ Keep all liquids away from the equipment to minimiz e the risk of accidental spillage. Liquid spilled on to the power
supply or on other hardware may cause damage, fire or electrical shock.
¦ Only qualified service personnel should open the chassis. Opening it yourself could damage the equipment and invali
date its warranty.
¦ If any part of the equipment becomes damaged or stops functioning, have it checked by qualified service personnel.
What the warranty does not cover
¦ Any product, on whi ch the serial number has been defaced, modified or removed.
¦ Damage, deterioration or malfunction resulting from:
? Accident, misuse, neglect, fire, water, li ghtning, or other acts of nature, unauthorized product modification, or
failure to follow instructions supplied with the product.
? Repair or attempted repair by anyone not authorized by us.
? Any damage of the product due to shipment.
? Removal or installation of the product.
? Causes external to the product, such as electric power fl uctuation or failure.
? Use of supplies or parts not meeting our specifications.
? Normal wear and tear.
? Any other ca uses which does not relate to a product defect.
¦ Removal, installation, and set-up service charges.
Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential instal - lation.
Any changes or modifications made to this equipme nt may void the user’s authority to operate this equipment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, m ay cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this eq uipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encou raged
to try to correct the interference by one or more of the followi ng measures:
¦ Re-position or relocate the receiving antenna.
¦ Increase the separation between the equipment and receiver.
¦ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
17” Industrial Panel Mount Widescreen LCD
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 3
Contents
< Part. 1 > APW 5170
1.1 Package Content
1.2 Structure Diagram & Dimension
1.3 Mounting Hardware & Installation
P.1
P.2 - 3
P.4 - 5
< Part. 2 > Specifications / OSD / Remote Controller
2.1 Product Specifications
2.2 On-screen Display Operation ( OSD )
2.3 Remote Controller ( RC-2 )
P.6 - 7
P.8 - 9
P.10
< Part. 3 >
Options
3.1 Option Table
3.2 3G / HD / SD-SDI Broadcast-grade input
3.3 MCS Multi-display control solution
3.4 X17" Touchscreen : Resistive, Capacitive
3.5 48V, 24V or 12VDC power
3.6 MIL-type or lockable connector
3.7 TV ( Analog )
P.11
P.12
P.13
P.14
P.15
P.16
P.17
APW 5170
17” Industrial Panel Mount Widescreen LCD
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All righ ts reserved. Product descripti on and product speci ficat ions
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 4
APW 5170
Before Installation
¦ It is very important to mount the equipment in a suitable cabinet or on a stable surface.
¦ Make sure the place has a good ventilation, is out of direct sunlight, away from sources of excessive
dust, dirt, heat, water, moisture and vibration.
Unpacking
The equipment comes with the standard parts shown in package content. Check and make sure they are
included and in good condition. If anything is missing, or damaged, contact the supplier immediatel y.
How To Clean Your LCD Monitor
Caution :
¦ To avoid the risk of electric shock, make sure your hands are dry before unplugging your monitor from or
plugging your monitor into an electrical outlet.
¦ When you clean your monito r, do not press down on the LCD screen. Pressing down on the screen can
scratch or damage your display. Pressure damage is not covered under warrant y.
¦ Use only cleansers m ade specifically for cleaning monitors and monitor screens. Cleansers not made to
clean monitors and monitor screens can scratch the LCD display or strip o ff the finish.
¦ Do not spray any kind of liquid directly onto the screen or case of your monito r. Spraying liquids directly
onto the screen or case can cause damage which is not covered under warrant y.
¦ Do not use paper towels or abrasive pads to clean your monito r. Using an abrasive pad or any wood based
paper product such as paper towels can scratch your LCD screen.
Cleaning Your Monitor
To clean your LCD safely, please follow these steps :
1
Disconnect the power cord.
2
Gently wipe the surface using a clean, dry microfiber cloth. Use as little pressure as possible.
Cleaning Tough Marks and Smudges
To remove tough marks and smudges, please follow these steps :
1
Disconnect the power cord.
2
Spray a small amount of non-abrasive cleanser on a microfiber cloth.
Caution : Do not spray or apply any liquids directly onto the monitor. Always apply the solution to your
microfiber cloth first, not directly on the parts you are cleaning.
3
Gently wipe the surface. Use as little pressure as possible.
4
Wait until your monitor is completely dry before plugging it in and powering it up.
17” Industrial Panel Mount Widescreen LCD
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 5
< Part 1 >
< 1.1 > Package Content – APW 5170
APW 5170
17” Widescreen LCD display X 1
6ft VGA cable X 1
Power cord X 1
Remote controller X 1
Mounting hardware X 1 pack
- Mounting bracket x 4 pcs
- M4* 6mm screw x 8 pcs
- M4* 50mm screw x 8 pcs
Standard I/O
Power BNC S-Video Audio
out - in - in
Video PC
HDMI
DVI-D VG A
- An abundance of input connections that include HDMI, DVI-D, VGA, S-Video + BNC and audio
- On-chip Faroudja® DCDi Cinema processing
APW 5170
17” Industrial Panel Mount Widescreen LCD
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All righ ts reserved. Product descripti on and product speci ficat ions
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 6
< 1.2 > Structure Diagram - APW 5170
1
2
3
Front view
4
AP-X17
NAP-X17
5
7
1 Rear case
2 LCD panel
3 Protective 3mm glass
4 6mm aluminum front bazel
5 Audio speaker, pair
6 LCD membrane
7 Remote sensor
Rear view
6
Model
Product Dimension
(W x D x H)
Packing Dimension
(W x D x H)
Net
Weight
Gross
Weight
APW5170
469 x 57 x 331 mm
18.4 x 2.2 x 13 inch
615 x 113 x 523 mm
24.2 x 4.4 x 20.6 inch
5.5 kg
12.1 lbs
8 kg
17.6 lbs
APW 5170
17” Industrial Panel Mount Widescreen LCD
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 7
< 1.2 > Dimension - APW 5170
Front View Side View
AP-X17
NAP-X17
Rear View
UNIT : mm
1mm = 0.03937 inch
Bottom View
Page 8
< 1.3 > Panel Mount Installation – APW 5170
1
Mounting
bracket
x 4 pcs
2 M4*6mm screw
x 8 pcs
3
M4*50mm screw
x 8 pcs
Hardware set part no. UV-BK#2
Steps
¦ Install 4 mounting brackets with 8 x M4*6mm screws
¦ Adjust the LCD panel with 8 x M4*50mm screws and fix it on the surface.
APW 5170
17” Industrial Panel Mount Widescreen LCD
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 9
APW 5170
< 1.3 > VESA mount Installation – APW 5170
M4 screw
VESA mount ( 100*100mm )
¦ Hardware and M4*4 pcs for VESA mount are not provided
17” Industrial Panel Mount Widescreen LCD
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All righ ts reserved. Product descripti on and product speci ficat ions
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 10
< Part 2 >
< 2.1 > Product Specifications
Mechanical
Design
APW 5170
Front Panel
Black, RAL 9005
Rear Casing
Dark grey, RAL 7037
VESA Mounting
100 x 100mm
Other Mounting
Panel mount
Protection
3mm protective glass
LCD
Panel
Panel Size ( diagonal )
17.1-inch Widescreen TFT color LCD
Display pixel ( dots x lines )
1920 x 1200
Brightness ( typ. )
210
Contrast Ratio ( typ. )
600:1
Color
16.7M, 8-bit
Viewing Angle ( L/R/U/D )
65/65/55/55
Response Time ( ms )
30
Dot pitch ( mm )
0.191
Display Area ( mm )
367.20H x 229.50V
Surface treatment
Anti-glare, Hard-coating
Surface hardness
3H
Backlight Type
LED
MTBF ( hrs )
20,000
Video
Connectivity
Digital
HDMI
HDMI 1.1, CEA-861-D
DVI
DVI-D, TMDS single link
Analog
VGA
Analog 0.7Vp-p
Composite ( RCA )
NTSC & PAL
S-Video ( 4-pin )
NTSC & PAL
Plug & Play
DVI / VGA
VESA EDID structure 1.3
Synchronization
VGA
Separate, Composite & SOG
Audio
Connectivity
Audio Input
Connector
3.5mm stereo jack
Impedance / Power level
30kΩ / 750mV
Audio Output
Connector
3.5mm stereo jack
Resistance / Power level
30kΩ / 2.8V
Speaker Output
Power
2 x 2W
*When th e audio output is connected, speaker output is OFF
Power
Power Supply
Range
Auto-sensing 100 to 240VAC,
50 / 60Hz
Power Consumption
Screen display ON
34W or less
Power saving mode
4W or less
Power button OFF
1W or less
Page 11
Regulatory Safety Approval FCC & CE
Environmental
Conditions
Operating
Temperature
0 to 50°C degree
Humidity
20~90%, non-condensing
Storage
Temperature
-5 to 60°C degree
Humidity
5~90%, non-condensing
Shock
10G acceleration (11ms duration)
Vibration
5~500Hz 1G RMS random
Physical
Specification
Product ( W x D x H )
469 x 57 x 331 mm
18.4 x 2.2 x 13 inch
Packing ( W x D x H )
615 x 113 x 523 mm
24.2 x 4.4 x 20.6 inch
Net Weight
5.5 kgs / 12.1 lbs
Gross Weight
8 kgs / 17.6 lbs
Applicable
Format
DVI-D / VGA Input
PC Signal
1920 x 1200 x 60Hz
1920 x 1080 x 60Hz
1280 x 1024 x 60 / 75Hz
1280 x 960 x 60Hz
1280 x 768 x 60 / 75Hz
1152 x 864 x 75Hz
1024 x 768 x 60 / 70 / 75Hz
848 x 480 x 60Hz
800 x 600 x 60 / 72 / 75Hz
720 x 400 x 70Hz
640 x 480 x 60 / 72 / 75Hz
640 x 400 x 70Hz
640 x 350 x 70Hz
HDMI Input
PC Signal
Same as VGA
Video Signal
1080p : 60Hz
720p : 50 / 60Hz
480p : 60Hz
576p : 50Hz
Audio Signal
2ch Linear PCM ( 32 / 44.1 / 48 KHz )
Composite / S-Video
Input
NTSC
525 lines, 60 fields / sec
PAL
625 lines, 50 fields / sec
Page 12
< 2.2 > On-screen Display Operation ( OSD )
Power light
Green = On
Orange = Power saving
Membran e Switch Function
Power on / off LCD
Display the OSD menu
Scrolls through menu options and adjusts the displayed control
(To auto adjustment by pressing the button for 5 seconds)
Exit the OSD screen
Toggle analog, digital & video connection (DVI-D and video options only)
1 Picture
Picture mode : Standard / Vivid / Soft / User mode to choose
Brightness : Adjust bac kground black level of the screen image
Contrast : Adjust the difference between the image background
(black level) and the foreground (white level)
Hue: Adjust the screen hue value
Saturation : Adjust the saturation of the image color
Picture size : Adjust the image size
Color temp : Standard / Cool / Warm / User to choose
Noise reduce : Reduce the noise of the image
Sharpness : Adjust the image from weak to sharp
2 PC
Auto adjust : Automatically adjust sizes, centers and fine tunes the
video signal to eliminate waviness and distortion.
Clock : Adjust the clock value
Phase : Adjust the phase value
H. Position : A lign the screen image left or right
V. P osition : Align the screen image up or down
Page 13
< 2.2 > On-screen Display Operation ( OSD )
3
Audio
Audio mode : Movie / Voice / Normal / Music mode to choose
Volume : Adjust the volume of sound
Bass : Set the value of bass sound
Treble : Set the value of treble sound
Balance : Set the balance value of treble and bass sound
Analog TV audio : Set the val ue of analog TV audio sound
Mute : Turn off the surrounding sound
4 TV
Auto search : Automatically search
Manual search : Search the TV manual
Fine tune : Fine tune the TV signal
Color system : Adjust the TV color
Sound system : Adjust the TV sound
Channel edit : Edit the channel
5
MISC
Language : Select the language in which the OSD menu is
displayed - English
Sleep timer : Set the off time
PIP mode : Adjust picture in picture setting
PIP position : Enter into PIP position
PIP source : Enter into the Sub source and sound source
System reset : Return the adjustment back to factory setting
Information : Select for Help
Page 14
r
< 2.3 > Remote Controller ( RC-2 )
1
8
2
INPUT MUTE
VOL
9
1 2 3
3
4 5 6
7 8 9
4
AUTO
0
-/--
CH
10
F REEZE
11
12
5
ME NU SELECT
ASP ECT 13
14
6 ENTE R
SLEE P
15
7
BA CK EXIT
16
PIP
17
20
SOURCE
21
SWAP
PIP
POS ITION
PIP
AUDI O 18
19
1
INPUT Select the source
2
Switches o n or off the TV
3 0 - 9
Only use in TV mode. Select channels. For channel numbers 10
and abo ve, enter the second digit withi n two seconds.
4 AUTO Auto adjust
5 MENU Display the menu on th e screen or go to the previous menu
Go to the upper menu or select the previous value /
Go to the next menu or select the next value /
6 ? / ? / ? / ? / ENTER Decrease the setting value /
Increase the setting value or enter to the select item setting
Enter to the select item settings or excude the setting
7
BACK Back to previous value
8 MUTE Turn on or off the speaker
9
Vol + / - Increase or decrease the speaker volume
10 CH + / - For TV model only, increase or de crease the channel number
11
FREEZE Reserve fo r OEM model
12
- / -- For setting input single or double digits
13 ASPECT Adjust the screen size
14
SELECT To select the existing item
15 SLEEP Select the sleeping time
16
EXIT Exit the menu o r can cel
PIP functions
17
PIP Picture in picture
18 PIP AUDIO To set the audi o of in PIP mode
19
POSITION To set the screen position in PIPmode
20 SOURCE PIP Source
21
SWAP Swap screen in PIP mode
Page 15
APW 5170
< Part 3 > Options
< 3.1 > Option Table
Options
APW
PMW
SDI ***
Touchscreen
MCS multi-display control ***
DC Power
MIL-type / lockable connector
TV ( Analog )
***
The user can only select eit her SDI or MCS inputs.
17” Industrial Panel Mount Widescreen LCD
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All righ ts reserved. Product descripti on and product speci ficat ions
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 16
< 3.2 > Options : 3G / HD / SD-SDI input
Acnodes’ SDI input is an ideal solution for the broadcastgrade video and high resolution CCTV market.
Designed for use with Full HD 1080p and ultra high resolution
1920 x 1200 LCD displays, Acnodes provides a SDI input
module without using additional space or power and it comes
standard with a 2-year warranty.
Power BNC S-Video
Audio
out - in - in
Video PC
HDMI
DVI-D VGA
SDI
out - in
INPUT
3G-SDI IN
BNC x 1 / 0.8Vp-p ( 75 ohm )
3G-SDI OUT
BNC x 1 / Active through, equalized & relocked
Standard Compliance
Video
SMPTE 425M / 274M / 296M / 125M
ITU-R BT.656
Audio
SMPTE 299M / 272M-C
Compatible Video Format
3G-SDI
1080p @60 / 50Hz, 4:2:2
1080p @30 / 25 / 24Hz, 4:4:4
1080i @60 / 50Hz, 4:4:4
720p @60 / 50Hz, 4:4:4
HD-SDI
1080p @30 / 25 / 24Hz, 4:2:2
1080i @60 / 50Hz, 4:2:2
720p @60 / 50Hz, 4:2:2
SD-SDI
480i @60Hz, 4:2:2
ITU-R BT.656
576i @50Hz, 4:2:2
Compatible Audio Format
3G-SDI
48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized Video
HD-SDI
48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized Video
SD-SDI
48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized /
Asynchronized Video
Max. Transmission Distance
75 ohm coaxial cable
3G-SDI
150m at 2.97Gb/s
HD-SDI
250m at 1.485Gb/s
SD-SDI
480m at 270Mb/s
APW 5170
17” Industrial Panel Mount Widescreen LCD
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 17
< 3.3 > Options : MCS
MCS
( Multi-display Control )
More control is always good. Especially when it is necessary and
easy. Acnodes provides MCS solution to control the OSD of
various LCD display up to 64 units.
The RS-232C is used for the communication between the PC and
the first display via a 15 feet serial cable while the CAN bus is
used for the various LCD displays cascade together via CAT 5/6
cable, and daisy chain up to 1,000 meters.
Designed for use with various LCD displays, Acnodes provides
a MCS input module without using additional space or power
and it comes standard with a 2-year warranty.
MCS
Power BNC S-Vi deo
Audio
out - in - in
Video PC
HDMI
DVI-D VGA
set out in Link
RS-232C
Set switch
For the 1st and last display,
push the set switch upward
15 feet serial cable
( over 15 feet, extender required )
For other daisy chain displays,
push the set switch downward
LINK OUT
IN OUT IN OUT IN OUT
Cat5 / 6 cable
max. 300 meters
Cat5 / 6 cable
max. 300 meters
Cat5 / 6 cable
max. 300 meters
RJ-45 jack
Daisy chain up to 1,000
meters and 64 displays
up to 64 displays
Page 18
< 3.4 > Options : Touchscreen & driver
17" USB Touchscreen Specification
Mod el
Technology
Touch Point
Method
Activation Force
Durability
Response Time
Optical Transmittance
Surface Hardness
Haze
Glass
Connector
Compatibility
TRB e-Resistive
TCB e-Capacitive
5-Wire Resistive
Capacitive
Single
Single
Stylus or Finger
Finger
= 50g / Stylus=R0.8
= 50g
10 million touches
300 million touches
15 ms
20 ms
80% ± 3%
92% ±2%
3H
9H
8% ± 3%
7%
2.2 ±0.2 mm
2.8 mm ±10%
USB Type A
Windows 7 / XP / Vista, Linux
¦ USB touchscreen package includes 1 x 6ft USB cable, quick reference guideline and CD disc
¦ For detailed information, please refer to the attached CD disc
¦ As the touchscreen unit is not made of toughened glass, please handle it carefully
USB Touchscreen
Power BNC S-Video
Audio
out - in - in
Video PC
HDMI
DVI-D VGA
APW 5170
17” Industrial Panel Mount Widescreen LCD
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 19
APW 5170
Please follow the below steps to s etup the touch screen:-
Step 1. Run the bundled CD disc
Step 2. Double click the Setup.exe
Step 3. Follow the installation instruction to finish the setup
Step 4. After installation, run the TouchKit program & the “4 point calibration”
Please do the initial calibration
after the first setup
17” Industrial Panel Mount Widescreen LCD
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All righ ts reserved. Product descripti on and product speci ficat ions
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 20
APW 5170
< 3.5 > Options : DC Power
Model
12V
24V
48V
Input rating
Input voltage:
12-Volt
24-Volt
48-Volt
Input range:
9 ~ 18V
18 ~ 36V
36 ~ 75V
Input current
- No load
50 mA
50 mA
50 mA
- Full load
4950 mA
2450 mA
1220 mA
Output rating
Output voltage:
12-Volt
12-Volt
12-Volt
Output current:
4.16A
4.16A
4.16A
Efficiency
84%
85%
85%
17” Industrial Panel Mount Widescreen LCD
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 21
APW 5170
< 3.6 > Options : MIL-type or Lockable Connector
Input
Part no.
MIL Standard
MIL - type
Connector
DC Power ***
( Male )
MS3470W8 -33P
MIL - DTL - 26482
VGA ***
( Male )
MS3470W14-15P
MIL - DTL - 26482
*** There are several additional MIL DC and VGA connector types with varying design
characteristics to meet cost considerations and to provide users with the most
design flexibility possible. For more information, please contact us.
Input
Part no.
Standard
Lockable
Connector
DC Power
( Male )
YM-Ext-461CP001
D-type 3W3
USB
LUSB - A111 - 00
-
*** MIL - type or Lockable connectors above can be integrated with our LCD displays.
Sale service just for connectors not provided.
17” Industrial Panel Mount Widescreen LCD
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All righ ts reserved. Product descripti on and product speci ficat ions
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 22
APW 5170
< 3.7 > Options : TV ( Analog )
TV
Power BNC S-Video
Audio
out - in - in
Video PC
HDMI
DVI-D VGA
***
( 1 ) For TV option, casing dimensions will be changed.
( 2 ) For RC-2 remote controller specifications, please refer to P.14
17” Industrial Panel Mount Widescreen LCD
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Loading...