ASSEMBLY INSTRUCTIONS
MODEL: 02053
PAGE 1 OF 4
NOTE: THIS ITEM NOT RECOMMENDED FOR COMMERCIAL USE
KEEP THIS DOCUMENT FOR REFERENCE IN CASE PARTS ARE NEEDED
DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED!!
BED PARTS HARDWARE PARTS
№ DESCRIPTION QTY № DESCRIPTION QTY
A
Left Side Panel
B
Right Side Panel
C
Bottom Frame
D
E
F
G
8
Top Frame
Guardrails
Supporting Leg
Metal Holder
1 PC 1
1 PC 2
1 PC 3
1 PC 4
2 PCS 5
2 PCS 6
2 PCS 7
Hex-Head ￠1/4”*35mm Bolts
Hex-Head ￠1/4”*75mm Bolts
Hex-Head ￠1/4”*60mm Bolts
￠1/4” locked Nuts
￠1/4”*20mm Nuts
Curved Washers 24 Pcs
Washers 12 Pcs
Allen Wrenches 1 Pc
2 Pcs
8 Pcs
16 Pcs
10 Pcs
8 Pcs
9
10
Plastic pads 4 Pcs
Open wrench 1 Pc
ASSEMBLY INSTRUCTIONS
MODEL: 02053
PAGE 2 OF 4
NOTE: THIS ITEM NOT RECOMMENDED FOR COMMERCIAL USE
KEEP THIS DOCUMENT FOR REFERENCE IN CASE PARTS ARE NEEDED
DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED!!
ASSEMBLY INSTRUCTIONS
MODEL: 02053
PAGE 3 OF 4
NOTE: THIS ITEM NOT RECOMMENDED FOR COMMERCIAL USE
KEEP THIS DOCUMENT FOR REFERENCE IN CASE PARTS ARE NEEDED
DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED!!
Remark:
1. Please always keep the warning lable on the inside of the upper bed end
structure permanently.
2. Phillips head screwdriver is required for tightening the self-tapping screws
ASSEMBLY INSTRUCTIONS
Replacement Parts
Replacement parts, including additional guardrails, may be obtained from any of our retail dealers.
Additional Note
SAFETY WARNINGS
(
ASTM
F1427
-
13)
MODEL: 02053
NOTE: THIS ITEM NOT RECOMMENDED FOR COMMERCIAL USE
KEEP THIS DOCUMENT FOR REFERENCE IN CASE PARTS ARE NEEDED
DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED!!
PAGE 4 OF 4
Size of Mattress
This bed is designed to use a mattress 74” x 37-1/2” – 38-1/2” on the upper bunk and 74” x 53-1/2” –
54” on the lower bunk. The thickness of the mattress must not exceed 6” on the upper bunk. There
must be at least 5” from mattress sleeping surface to top edge of guard rail on the upper bunk.
Maximum total weight not to exceed 150 lbs. on the upper bunk, and maximum 200 lbs. on the lower
bunk.
1. Follow the information on the warnings appearing on the upper bunk end structure and on the
carton. Do not remove warning label from bed.
2. Always use the recommended size mattresses or mattress supports, or both, to help prevent the
likelihood of entrapment or falls.
3. Surface of mattress must be at least 5 in. (127 mm) below the upper edge of guardrails.
4. Do not allow children under 6 years of age to use the upper bunk.
5. Periodically check and ensure that the guardrail, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
6. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
7. Always use the ladder for entering and leaving the upper bunk.
8. Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
9. Use of a night light may provide added safety precaution for a child using the upper bunk.
10. Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed next to
the wall, the guardrail that runs the full length of the bed should be placed against the wall to
prevent entrapment between the bed and wall.
11. The use of water or sleep flotation mattresses is prohibited.
12. STRANGULATION HAZARD–Never attach or hang items to any part of the bunk bed that are not
designed for use with the bed; for example, but not limited to, hooks, belts and jump ropes.
13. Keep these instructions for future reference.
14. Prohibit more than one person on upper bunk.
15. Adult assembly required due to the presence of small parts ,sharp points,sharp edgesas recesived.
SAFETY WARNINGS ( 16 CFR 1513)
(1) Do not allow children under 6 years of age to use the upper bunk.
(2) Use guardrails on both sides of the upper bunk.
(3) Prohibit horseplay on or under beds.
(4) Prohibit more than one person on upper bunk.
(5) Use ladder for entering or leaving upper bunk.
(6) If the bunk bed will be placed next to a wall, the guardrail that runs the full length of
the bed should be placed against the wall to prevent entrapment between the bed and
the wall. (This applies only to bunk beds without two full-length guardrails.)
Loading...