ASSEMBLY INSTRUCTIONS
BED PARTS
HARDWARE PARTS
№
DESCRIPTION
QTY
№
DESCRIPTION
QTY
A
Left Side Panel
1 PC
1
Hex-Head ￠1/4”*35mm Bolts
2 Pcs
B
Right Side Panel
1 PC
2
Hex-Head ￠1/4”*75mm Bolts
8 Pcs
C
Bottom Frame
1 PC
3
Hex-Head ￠1/4”*60mm Bolts
16 Pcs
D
Top Frame
1 PC
4
￠1/4” locked Nuts
10 Pcs
E
Guardrails
2 PCS
5
￠1/4”*20mm Nuts
8 Pcs
F
Supporting Leg
2 PCS
6 Curved Washers
24 Pcs
G
Metal Holder
2 PCS
7 Washers
12 Pcs
8 Allen Wrenches
1 Pc
9 Plastic pads
4 Pcs
10 Open wrench
1 Pc
MODEL: 02052 PAGE 1 OF 4
NOTE: THIS ITEM NOT RECOMMENDED FOR COMMERCIAL USE
KEEP THIS DOCUMENT FOR REFERENCE IN CASE PARTS ARE NEEDED
DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED!!
ASSEMBLY INSTRUCTIONS
STEP 1
STEP 2
MODEL: 02052 PAGE 2 OF 4
NOTE: THIS ITEM NOT RECOMMENDED FOR COMMERCIAL USE
KEEP THIS DOCUMENT FOR REFERENCE IN CASE PARTS ARE NEEDED
DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED!!
ASSEMBLY INSTRUCTIONS
STEP 3
STEP 4
MODEL: 02052 PAGE 3 OF 4
NOTE: THIS ITEM NOT RECOMMENDED FOR COMMERCIAL USE
KEEP THIS DOCUMENT FOR REFERENCE IN CASE PARTS ARE NEEDED
DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED!!
ASSEMBLY INSTRUCTIONS
Remark:
1. Please always keep the warning lable on the inside of the upper bed end structure
permanently.
2. Phillips head screwdriver is required for tightening the self-tapping screws.
Size of Mattress
This bed is designed to use a mattress 80” x 37-1/2” – 38-1/2” on the upper bunk and 80” x 59-1/2” –
60” on the lower bunk. The thickness of the mattress must not exceed 6” on the upper bunk. There
must be at least 5” from mattress sleeping surface to top edge of guard rail on the upper bunk.
Replacement Parts
Replacement parts, including additional guardrails, may be obtained from any of our retail dealers.
Additional Note
Maximum total weight not to exceed 150 lbs. on the upper bunk, and maximum 200 lbs. on the lower
bunk. Factroy suggestion--Maximum total weight not to exceed 300 lbs. on the upper bunk, and
maximum 500 lbs. on the lower bunk.
SAFETY WARNINGS (ASTM F1427-13)
1. Follow the information on the warnings appearing on the upper bunk end structure and on the
carton. Do not remove warning label from bed.
2. Always use the recommended size mattresses or mattress supports, or both, to help prevent the
likelihood of entrapment or falls.
3. Surface of mattress must be at least 5 in. (127 mm) below the upper edge of guardrails.
4. Do not allow children under 6 years of age to use the upper bunk.
5. Periodically check and ensure that the guardrail, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
6. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
7. Always use the ladder for entering and leaving the upper bunk.
8. Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
9. Use of a night light may provide added safety precaution for a child using the upper bunk.
10. Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed next to
the wall, the guardrail that runs the full length of the bed should be placed against the wall to
prevent entrapment between the bed and wall.
11. The use of water or sleep flotation mattresses is prohibited.
12. STRANGULATION HAZARD–Never attach or hang items to any part of the bunk bed that are not
designed for use with the bed; for example, but not limited to, hooks, belts and jump ropes.
13. Keep these instructions for future reference.
14. Prohibit more than one person on upper bunk.
15. Adult assembly required due to the presence of small parts ,sharp points,sharp edgesas recesived.
SAFETY WARNINGS ( 16 CFR 1513)
(1) Do not allow children under 6 years of age to use the upper bunk.
(2) Use guardrails on both sides of the upper bunk.
(3) Prohibit horseplay on or under beds.
(4) Prohibit more than one person on upper bunk.
(5) Use ladder for entering or leaving upper bunk.
(6) If the bunk bed will be placed next to a wall, the guardrail that runs the full length of
the bed should be placed against the wall to prevent entrapment between the bed and
the wall. (This applies only to bunk beds without two full-length guardrails.)
MODEL: 02052 PAGE 4 OF 4
NOTE: THIS ITEM NOT RECOMMENDED FOR COMMERCIAL USE
KEEP THIS DOCUMENT FOR REFERENCE IN CASE PARTS ARE NEEDED
DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED!!
Loading...