ACI-Automation Components BOARD ONLY Data Sheet
TEMPERATURE | TRANSMITTERS | BOARD ONLY
BOARD ONLY
Calibrated Transmitter, No Sensor
The ACI Transmitter Board Only Series features a two-wire, 4 to 20 mA loop powered output
signal with optional 3-Wire voltage output signals available. Sensors are not included with the
board only transmitter since they are designed to be used with any existing 100 or 1000 Ohm
Platinum RTD sensor with a 385 temperature coecient. All transmitters must be ordered with
the temperature span that you require, since the boards are tuned to give you the best
performance characteristics for the temperature span specied. Zero and Span adjustments are
available for recalibration in the eld when using NIST Certied equipment. We recommend
the use of an 18 to 22 AWG shielded cable for all temperature transmitter installations to protect
against the introduction of noise onto the signal lines. For applications in which a much you are
looking for increased temperature performance and a higher level of corrosion and moisture resistance, our Ruggedized (Thermally Conductive
Epoxy Coated) transmitters are also available. ACI does oer recalibration services for any transmitters sent back to us for a nominal fee.
Applications: Replacement Temperature Transmitters, High Moisture and Corrosive Environments, Conversion of existing Platinum 2 or 3 Wire
RTD’s to linear current or voltage output signal, transmit signals over long wire runs
Automation Components, Inc.
PRODUCT SPECIFICATIONS
Transmitter Supply Voltage | Supply Current:
Maximum Load Resistance:
Transmitter Output Signals:
Calibrated Accuracy | Linearity:
Temperature Drift:
Calibrated Temperature Spans:
Sensor Type Accepted | Sensor Curve:
Sensor Resistance Characteristics (Nominal):
Sensor Din Standard | Temperature Coecient:
Warm Up Time | Warm Up Drift:
Operating Temperature Range:
Storage Temperature Range:
Operating Humidity Range:
Connections | Wire Size:
Terminal Block Torque Rating
Conformal Coating Material:
Conformal Coating Approval Ratings:
Dielectric Withstand Voltage Rating:
Insulation Resistance:
Moisture Insulation Resistance:
Conformal Coating Flammability Rating:
Conformal Coating Temperature Rating:
Resistance to Chemicals | Fungus Resistant:
Mounting Conguration:
Stando Material Type | Flammability Rating:
Stando Temperature Rating:
Stando Dimensions:
Product Dimensions (L x W x H) | Product Weight:
Agency Approvals:
Note: Transmitter’s calibrated at 71ºF (22ºC) nominal | Note: Temperature Drift is referenced to 71ºF nominal calibration temperature
+8.5 to 32 VDC (Reverse Polarity Protected) | 25 mA minimum
250 Ohm Load: +13.5 to 32 VDC | 500 Ohm Load: +18.5 to 32 VDC
(Terminal Voltage - 8.5 V) / 0.020 A
Current: 4-20 mA (2-Wire, Loop Powered) | Voltage: 1-5 VDC or 2-10 VDC (3-Wires)
Temp. Spans < 500ºF (260ºC): +/- 0.2% | Temp. Spans > 500ºF (260ºC): +/- 0.5%
Temp. Spans < 100ºF (38ºC): +/- 0.04%/ºF | Temp. Spans > 100ºF (38ºC): +/- 0.02%
Minimum Temp. Span: 50ºF (28ºC) | Maximum Temp. Span: 1000ºF (538ºC)
Platinum RTD | PTC (Positive Temperature Coecient)
A/TT100 Series: 100 Ohms @ 32ºF (0ºC) | A/TT1K Series: 1000 Ohms @ 32ºF (0ºC)
DIN EN 60751 (IEC 751) | 3850 ppm / ºC
10 Minutes | +/- 0.1%
-40ºF to 185ºF (-40 to 85ºC)
-40 to 80ºC (-40 to 176ºF)
0 to 90%, non-condensing
Screw Terminal Blocks (Non-Polarity Sensitive) | 16 AWG (1.31 mm) to 26 AWG (0.129 mm)
0.37 ft-lb (0.5 Nm) nominal
UV Curable, Acrylated Polyurethane
MIL-I-46058C Qualied and IPC-CC 830 | UL File Number E105698
> 1500 volts / MIL-I-46058C
8.0 x 1014 Ohms (800 Tera Ohms), per MIL-I-46058C
4.7 x 1010 Ohms (47 Giga Ohms), per MIL-I-46058C
UL94-V0
-65 to 125ºC (-85 to 257ºF)
Excellent | Pass per ASTM G21
Three Adhesive Standos included
Nylon 66 | UL94-V2
-40 to 85ºC (-40 to 185ºF)
0.70” (17.8 mm) x 0.70” (17.8 mm) x 0.65” (16.5 mm)
2.30” (58.42 mm) x 1.478” (37.54 mm) x 0.775” (19.69 mm) | 0.034 lbs. (15.4 g)
RoHS2, WEEE
Call: 1-888-967-5224 | Web: www.workaci.com
TEMPERATURE | ##
TEMPERATURE | TRANSMITTERS | BOARD ONLY
DIMENSIONAL DRAWING
1.06”(26.96mm)
1.10” (27.91mm)
.78” (19.73mm)
1.47”
(37.39mm)
2.30” (58.34mm)
Front View Right View Top View
Automation Components, Inc.
.54”
(13.75mm)
.11” (2.76mm)
STANDARD ORDERING
Model #
A/TT100-BO-1
A/TT100-BO-2
A/TT100-BO-4
A/TT1K-BO-1
A/TT1K-BO-2
A/TT1K-BO-4
CUSTOM ORDERING
A. Sensor Series
B. Model Series
C. Conguration
No Selection Required
Select One (1)
No Selection Required
Select One (1)
Item #
118459
118460
118462
118689
118692
118694
Model # Example:
Description
TT100 Board Only with 1-5 VDC Output and Adhesive Standos (Specify Temperature Span)
TT100 Board Only with 2-10 VDC Output and Adhesive Standos (Specify Temperature Span)
TT100 Board Only with 4-20 mA Output and Adhesive Standos (Specify Temperature Span)
TT1K Board Only with 1-5 VDC Output and Adhesive Standos (Specify Temperature Span)
TT1K Board Only with 2-10 VDC Output and Adhesive Standos (Specify Temperature Span)
TT1K Board Only with 4-20 mA Output and Adhesive Standos (Specify Temperature Span)
Model # Example:
A/A.TT100B.BOC.1
0 to 40ºC
E.
D.
A/
TT100 = Accepts 100 Ohm Platinum RTD | TT1K = Accepts 1K Ohm Platinum RTD
BO = Board Only
1 = 1 to 5 VDC | 2 = 2 to 10 VDC | 4 = 4 to 20 mAD. Output Signal
Specify Span in ºF or ºC (Best Accuracy in 100ºF Increments)E. Calibrated Span
-OR-
118462A/TT100-BO-4
MODEL #
A/
BO
TEMPERATURE | ##
Revision C0000002 | Rev 1.0
Call: 1-888-967-5224 | Web: www.workaci.com
Loading...