ACI-Automation Components A/TT100-BP-2-GD-6 Data Sheet
Automation Components, Inc.
TEMPERATURE | TRANSMITTERS | BULLET PROBE
BULLET PROBE
Remote Probes with Transmitters
The ACI Transmitter Bullet Probe Series features a two-wire, 4 to 20 mA loop powered output
signal with an optional 3-Wire voltage output signal available. All transmitters include Zero and
Span adjustments for eld calibration and are calibrated using NIST Certied Calibration
equipment. We recommend the use of an 18 to 22 AWG shielded cable for all temperature
transmitter installations to help eliminate the possibility of noise being introduced onto the
signal lines. The sensor assemblies are manufactured using a 2 conductor unshielded FEP/FEP
Plenum rated, unshielded cable and ACI’s proven double encapsulation process to eliminate
the eects of moisture on the sensors as well as increased response times using our high
quality, thermally conductive epoxy. The Bullet Probe remote sensors include an optional 10 or
20 Foot Plenum rated cable for use in remote sensor applications. All TT100 and TT1K Series
Bullet Probe transmitter’s sensor leads may be shortened in the eld as needed but all Matched
TTM100 and TTM1K Series transmitter’s sensor leads should not be shortened due to the aect that it would have on the calibration accuracy of the
sensor and transmitter. Optional NEMA/IP rated weather proof enclosures are available as specied on the back of the product data sheet. For best
accuracy, ACI recommends the use of the A/TTM Series Matched transmitters with 3 or 5 Point NIST Calibration Certicate, since they include a
second calibration step in which the RTD and transmitter are calibrated together as a system.
Applications: Chilled Water Systems, Hot Water Systems, Boilers, Pumps, Compressors, Chillers, Remote Sensing, Process Control
PRODUCT SPECIFICATIONS
Transmitter Supply Voltage | Supply Current:
Maximum Load Resistance:
Output Signals:
Calibrated Accuracy | Linearity:
Thermal Drift:
Min./Max. Calibrated Temperature Spans:
TTM100/TTM1K Certication Points:
Warm Up Time | Warm Up Drift:
Transmitter Operating Temperature Range:
Transmitter Operating Humidity Range:
Connections | Wire Size:
Terminal Block Torque Rating:
Sensor Type | Sensor Curve | Sensing Points:
Number Wires | Wire Colors:
Sensor Output @ 0°C (32°F):
RTD Tolerance Class | Accuracy:
Din Standard | Temperature Coecient:
Sensor Stability:
Response Time (63% Step Change):
Sensor Operating Temperature Range:
Enclosure Specications (Operating Temperature,
Material, Flammability, NEMA/IP Ratings):
Storage Temperature Range:
Operating Humidity Range:
Probe Diameter | Probe Material:
Cord Grip Fitting Material | Flammability Rating:
Cord Grip Seal Material | NEMA/IP Rating:
Torque Recommendation Cord Grip:
Lead Length | Cable Diameter | Conductor Size:
Lead Wire Insulation | Wire Rating:
Conductor Material:
Product Dimensions | Product Weight:
Agency Approvals:
Note: Transmitter’s calibrated at 71ºF (22ºC) nominal | Note: Temperature Drift is referenced to 71ºF nominal calibration temperature
+8.5 to 32 VDC (Reverse Polarity Protected) | 25 mA minimum
250 Ohm Load: +13.5 to 32 VDC | 500 Ohm Load: +18.5 to 32 VDC
(Terminal Voltage - 8.5 V) | 0.020 A
Current: 4-20 mA (2-Wire Loop Powered) | Voltage: 1-5 VDC or 2-10 VDC (3-Wires)
Temp. Spans < 500ºF (260ºC): +/- 0.2%
Temp. Spans < 100ºF (38ºC): +/- 0.04%/ºF | Temp. Spans > 100ºF (38ºC): +/- 0.02%
Minimum Temp. Span: 50ºF (28ºC) | Maximum Temp. Span: 400ºF (204ºC)
3 Point NIST: 20%, 50% & 80% of span | 5 Point NIST: 0%, 20%, 50%, 80% & 100% of span
10 Minutes | +/- 0.1%
-40ºF to 185ºF (-40 to 85ºC)
0 to 90%, non-condensing
Screw Terminal Blocks | 16 AWG (1.31 mm) to 26 AWG (0.129 mm)
0.37 ft-lb (0.5 Nm ) nominal
Platinum RTD | PTC (Positive Temperature Coecient) | One
Two | Red and Black (Non Polarity Sensitive)
A/TT100/TTM100 Series: 100 Ohms nominal | A/TT1K/TTM1K Series: 1000 Ohms nominal
+/- 0.06% Class A | (Tolerance Formula: +/- ºC = (0.15ºC + (0.002 * |t|))
where |t| is the absolute value of temperature above or below 0ºC in ºC)
DIN EN 60751 (IEC 751) | 3850 ppm / ºC
+/- 0.03% after 1000 Hours @ 300ºC (572ºF)
8 Seconds nominal
-40 to 150ºC (-40 to 302ºF)
“-GD” Enclosure: Galvanized Steel, -40 to 85ºC (-40 to 185ºF), NEMA 1 (IP10)
“-PB” Enclosure: ABS Plastic, -30 to 85ºC (-22 to 185ºF), UL94-HB, Plenum Rated
“-BB” Enclosure: Aluminum, -40 to 85ºC (-40 to 185ºF), NEMA 3R (IP 14)
“-4X” Enclosure: Polystyrene Plastic, -40 to 70ºC (-40 to 158ºF), UL94-V2, NEMA 4X (IP 66)
-40 to 80ºC (-40 to 176ºF)
5 to 95% RH, non-condensing
0.250” (6.35mm) | 304 Stainless Steel
Polyamide 6.6 | UL94-V2
Neoprene | IP68 (NEMA 4X)
1.83 ft-lbs (2.50 Nm)
10’ (3.05 m) or 20’ (6.1 m) | 0.106” nominal (2.69 mm) | 22 AWG (0.65mm)
FEP/FEP Teon Unshielded Cable | UL CL2P or CL3P; CMP C(UL) US 150ºC, FT-6
Tin Plated Copper
See table on back of Product Data sheet
RoHS2, WEEE
Call: 1-888-967-5224 | Web: www.workaci.com
TEMPERATURE | ##
TEMPERATURE | TRANSMITTERS | BULLET PROBE
DIMENSIONAL DRAWING
Automation Components, Inc.
1.00” (25.40mm)
Ø.25”
(6.35mm)
Standard View
CUSTOM ORDERING
A. Sensor Series
B. Model Series
C. Conguration
D. Output Signal
No Selection Required
Select One (1)
No Selection Required
Select One (1)
Select One (1)
Select One (1)
A/
TT100 = 100 | TTM100* = Matched 100 | TT1K = 1K | TTM1K* = Matched 100
BP = 1” Stainless Steel Probe
1 = 1 to 5 VDC | 2 = 2 to 10 VDC | 4 = 4 to 20 mA
GD = Galvanized | PB = Plastic | BB = Aluminum, NEMA 3R | 4X = NEMA 4XE. Enclosure
10’CL2P = 10 Feet (3.05 m) Plenum Cable | 20’CL2P = 20 Feet (6.1 m) Plenum Cable F. Cable Length
Model # Example:
Specify Span in ºF or ºC (Best Accuracy in 100ºF Increments)G. Calibrated Span
Note*: Must specify a 3 or 5 Point NIST Certicate with the TTM100 or TTM1K Transmitter above
ACCESSORIES ORDERING
Model #
HARDWARE, ¼” MOUNTING CLIP
HARDWARE, ¼” U-MOUNTING CLIP
Item #
108169
100090
Description
Hardware, ¼” Mounting Clip
Hardware, ¼” U-Mounting Clip Adhesive
10.00’ (3.05mm)
.31” Stripping Length
(7.87mm)
TT100
A/
A.
B.
BPC.1D.PB
10’CL2PF.0 to 40ºC
E.
G.
MODEL #
A/
BP
Model # Example:
Galvanized Metal•Plastic w/ Adhesive
-OR-
108169HARDWARE, ¼” MOUNTING CLIP
•
TEMPERATURE | ##
Revision C0000002 | Rev 1.0
Call: 1-888-967-5224 | Web: www.workaci.com
Loading...