Acer UM.UX6EE.C01 Quick Start Guide

Acer LCD Monitor Quick Start Guide (QSG)

Important safety instructions

Please read the following instructions carefully.

1.To clean the LCD monitor screen:

	Turn off the LCD monitor and unplug the power cord.
	Spray a non-solvent cleaning solution onto a rag and clean the screen gently.

2.Do not place the LCD monitor near a window. Exposing the monitor to rain, moisture or sunlight can severely damage it.

3.Do not apply pressure to the LCD screen. Excessive pressure may cause permanent damage to the display.

4.Do not remove the cover or attempt to service this unit yourself. An authorized technician should perform servicing of any nature.

5.Store the LCD monitor in a room with a temperature of -20° to 60° C (-4° to140° F). Storing the LCD monitor outside this range may result in permanent damage.

6.Immediately unplug your monitor and call an authorized technician if any of the following circumstances occur:

	Monitor-to-PC signal cable is frayed or damaged.
	Liquid spills onto the LCD monitor or the monitor is exposed to rain.
	The LCD monitor or case is damaged.

Package contents

	LCD	Power cord	VGA cable	DVI cable	Quick start	HDMI Cable
	monitor		(optional)	(optional)	guide	(Optional)

Attaching the monitor to the base

1 Remove the monitor base from the packaging and place it on a stable and level workspace.

2Remove the monitor from the packaging.

3Align the release button at the buttom of the monitor with the corresponding slot at the bottom of the base. A clicking sound signifies that the monitor has been securely attached to the base.

Connecting your monitor to a computer

1.Turn off your computer and unplug your computer's power

cord.

2.Connect the signal cable to the VGA and/or DVI-D/HDMI

	(optional) input socket of the monitor, and the
	VGA and/or DVI-D/HDMI (optional) output socket of
	the graphics card on the computer. Then tighten the
	thumbscrews on the signal cable connector.
3.	Insert the monitor power cable into the power port at the
	back of the monitor.
4.	Plug the power cords of your computer and your monitor
	into a nearby electrical outlet.	2

English

English

	External controls
1&2				Power button	Turns the monitor on/off. Blue indicates power on. Amber indicates
					standby/ power saving mode.
3&4			</>	Minus / Plus	If the OSD is active, press the Minus or Plus buttons to toggle between
					the OSD options. If the OSD is inactive, press the Minus or Plus buttons to
					adjust the volume. (Optional)
5			Menu	OSD functions	Press to view the OSD. Press again to enter a selection in the OSD.
6			Auto	Auto	If the OSD is active, press Auto to exit the OSD. Once the OSD is inactive,
					press Auto and the monitor will automatically optimize the display
					position, focus, and clock of your display.
				Empowering	a. When the OSD menu is active, this button will act as the exit key ( exit
7				Key	OSD menu).
					b. When the OSD menu is inactive, press this button to select scenario

mode.

Regulations and safety notices

FCC notices

This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio

or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

	Reorient or relocate the receiving antenna.
	Increase the separation between the device and receiver.
	Connect the device into an outlet on a circuit different from that to which the receiver is connected.
	Consult the dealer or an experienced radio/television technician for help.

CE declaration of conformity

Hereby, Acer Inc., declares that this LCD monitor is in compliance with the essential requirements and other relevant provisions of EMC Directive 2004/108/EC, Low Voltage Directive 2006/95/EC, and RoHS Directive 2011/65/EU and Directive 2009/125/EC with regard to establishing a framework for the setting of ecodesign requirements for energy-related product.

Notice: Shielded cables

All connections to other computing devices must be made using shielded cables to maintain compliance with EMC regulations.

Notice: Peripheral devices

Only peripherals (input/output devices, terminals, printers, etc.) certified to comply with the Class B limits may be attached to this equipment. Operation with non-certified peripherals is likely to result in interference to radio and TV reception.

Caution

Changes or modifications not expressly approved by the manufacturer could void the user authority, which is granted by the Federal Communications Commission, to operate this product.

In order to prevent damage to the monitor, do not lift the monitor by its base.

Operation conditions

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Notice: Canadian users

&$1 ,&(6 % 10% %