Page 1
Acer LCD Monitor
User's Guide
Page 2
Copyright © 2013 . Acer Incorporated.
All Rights Reserved.
Acer LCD Monitor User's Guide
Original Issue: 01/20
Changes may be made periodically to the information in this publication without obligation
to notify any person of such revisions or changes. Such changes will be incorporated in new
editions of this manual or supplementary documents and publications. This company makes
no representations or warranties, either expressed or implied, with respect to the contents
hereof and specifically disclaims the implied warranties of merchantability or fitness for a
particular purpose.
Record the model number, serial number, purchase date and place of purchase information in
the space provided below. The serial number and model number are recorded on the label
affixed to your computer. All correspondence concerning your unit should include the serial
number, model number and purchase information.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronically, mechanically, by photocopy, recording or otherwise,
without the prior written permission of Acer Incorporated.
13
Acer LCD Monitor User's Guide
Model number: __________________________________
Serial number: ___________________________________
Date of purchase: ________________________________
Place of purchase: ________________________________
Acer and the Acer logo are registered trademarks of Acer Incorporated. Other companies'
product names or trademarks are used herein for identification purposes only and belong to
their respective companies.
Page 3
Special notes on LCD monitors
The following are normal with the LCD
Due to the nature of the fluorescen
•
initial use. Turn off the power switch and then turn it on again to make
sure the flicker disappears.
You may find slightly uneven b
•
desktop pattern you use.
The LCD screen has 99.99% or more effective p
•
blemishes of 0.01% or less such as a missing pixel or a pixel lit all the time.
Due to the nature of the LCD screen, an afterimage of
•
may remain after switching the image, when the same image is displayed
for hours. In this case, the screen is recovered slowly by changing the image
or turning off the power switch for a few hours.
monitor and do not indicate a problem.
t light, the screen may flicker during
rightness on the screen depending on the
ixels. It may include
the previous screen
Information for your safety and
comfort
Safety instructions
iii
Read these instructions caref
Follow all warnings and instructions marked on the product.
ully. Keep this document for future reference.
Cleaning your monitor
Please carefully follow these guidelines
•
Always unplug the moni
Use a soft cloth to wipe the screen and cabi
•
tor before cleaning.
when cleaning the monitor:
net front and sides.
Connecting/disconnecting the device
Observe the following guidelines when connecting and disconnecting power
from the LCD monitor:
Make sure the monitor is attached to its base before co
•
cord to the AC power outlet.
•
Make sure both the LCD monitor and t
connecting any cable or unplugging the power cord.
• If the system has multiple sources
system by unplugging all power cords from the power supplies.
he computer are turned off before
of power, disconnect power from the
nnecting the power
Page 4
iv
Accessibility
Be sure that the power outlet you plug the po
and located as close to the equipment operator as possible. When you need to
disconnect power from the equipment, be sure to unplug the power cord from
the electrical outlet.
wer cord into is easily accessible
Safe listening
To protect your hearing, follow these in
Gradually increase the volume until yo
•
and without distortion.
After setting the volume level, do no
•
adjusted.
Limit the amount of time listening to music at
•
Avoid turning up the volu
•
Turn the volume down if
•
me to block out noisy surroundings.
you can't hear people speaking near you.
structions.
u can hear it clearly and comfortably
t increase it after your ears have
high volume.
Warnings
Do not use this
•
•
Do not place this product on an
falls, it could be seriously damaged.
Slots and openings are provided for vent
•
operation of the product and to protect it from overheating. These
openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug or other similar surface.
This product should never be placed near or over a radiator or heat
register, or in a built-in installation unless proper ventilation is provided.
•
Never push objects of any kind in
they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind onto or into
the product.
To avoid damage of internal compon
•
do not place the product on a vibrating surface.
Never use it under sporting, exercisin
•
which will probably cause unexpected short current or damage internal
devices.
product near water.
unstable cart, stand or table. If the product
ilation to ensure reliable
to this product through cabinet slots as
ents and to prevent battery leakage,
g, or any vibrating environment
Using electrical power
This product should be operated from
•
marking label. If you are not sure of the type of power available, consult
your dealer or local power company.
• Do not allow anything to re
product where people will walk on the cord.
st on the power cord. Do not locate this
• If an extension cord is used with this prod
the type of power indicated on the
uct, make sure that the total
Page 5
ampere rating of the equipment plugged into the extension cord does not
exceed the extension cord ampere rating. Also, make sure that the total
rating of all products plugged into the wall outlet does not exceed the fuse
rating.
Do not overload a power outlet, strip or receptacle by plugging in too
•
many devices. The overall system load must not exceed 80% of the branch
circuit rating. If power strips are used, the load should not exceed 80% of
the power strip's input rating.
• This product's power cord is equipped with a three-wire grounded plug.
The plug only fits in a grounded power outlet. Make sure the power outlet
is properly grounded before inserting the power cord plug. Do not insert
the plug into a non-grounded power outlet. Contact your electrician for
details.
Warning! The grounding pin is a safety feature. Using a power
outlet that is not properly grounded may result in electric shock
and/or injury.
Note: The grounding pin also provides good protection from
unexpected noise produced by other nearby electrical devices that
may interfere with the performance of this product.
Use the product only with the supplied power supply cord set. If you need
•
to replace the power cord set, make sure that the new power cord meets
the following requirements: detachable type, UL listed/CSA certified, type
SPT-2, rated 7 A 125 V minimum, VDE approved or its equivalent, 4.5
meters (15 feet) maximum length.
v
Product servicing
Do not attempt to service this product yourself, as opening or removing covers
may expose you to dangerous voltage points or other risks. Refer all servicing to
qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service
personnel when:
•
the power cord or plug is damaged, cut or frayed
• liquid was spilled into the product
the product was exposed to rain or water
•
the product has been dropped or the case has been damaged
•
•
the product exhibits a distinct change in performance, indicating a need
for service
• the product does not operate normally after following the operating
instructions
Page 6
vi
Note: Adjust only those controls that are covered by the operating
instructions, since improper adjustment of other controls may
result in damage and will often require extensive work by a
qualified technician to restore the product to normal condition.
Potentially explosive environments
Switch off your device in any area with a potentially explosive atmosphere and
obey all signs and instructions. Potentially explosive atmospheres include areas
where you would normally be advised to turn off your vehicle engine. Sparks in
such areas could cause an explosion or fire resulting in bodily injury or even
death. Switch off the device near gas pumps at service stations. Observe
restrictions on the use of radio equipment in fuel depots, storage and
distribution areas; chemical plants; or where blasting operations are in progress.
Areas with a potentially explosive atmosphere are often, but not always,
marked. They include below deck on boats, chemical transfer or storage
facilities, vehicles using liquefied petroleum gas (such as propane or butane),
and areas where the air contains chemicals or particles such as grain, dust or
metal powders.
Additional safety information
Your device and its enhancements may contain small parts. Keep them out of
the reach of small children.
IT Equipment Recycling Information
Acer is strongly committed to environmental protection and views recycling, in
the form of salvaging and disposal of used equipment, as one of the company's
top priorities in minimizing the burden placed on the environment.
We at Acer are very conscious of the environmental effects of our business and
strive to identify and provide the best working procedures to reduce the
environmental impact of our products.
For more information and help when recycling, please go to this website:
http://www.acer-group.com/public/Sustainability
Visit www. .com
of our other products.
acer-group
for further information on the features and benefits
Page 7
vii
Disposal instructions
Do not throw this electronic device into the trash when discarding.
To minimize pollution and ensure utmost protection of the global environment,
please recycle. For more information on the Waste from Electrical and
Electronics Equipment (WEEE) regulations, visit
http://www.acer‐group.com/public/Sustainability
LCD pixel statement
The LCD unit is produced with high-precision manufacturing techniques.
Nevertheless, some pixels may occasionally misfire or appear as black or
red dots. This has no effect on the recorded image and does not constitute
a malfunction.
Warning Message for Magnet
Certain electronic devices such as hard drives, USB devices, tablet computers,
laptops, cellphones, watches, earphones, speakers, credit cards, magnetic ID
cards, etc. are sensitive to magnetic fields and may be damaged permanently or
temporarily disabled if exposed to a magnetic field that is too strong.
Electronic devices should not be put close to or directly on the magnetic area
of monitor base.
Magnet
Page 8
viii
This product has been shipped enabled
Activate display’s Sleep mode within 15 minutes of
•
•
Activate computer’s Sleep
•
Wake the computer fro
Tips and information for comfor
Computer users may co
Users are also at risk of physical injury after long hours of working in front of a
computer. Long work periods, bad posture, poor work habits, stress,
inadequate working conditions, personal health and other factors greatly
increase the risk of physical injury.
Incorrect computer usage may lead to carpal tunnel syndrome, tendonitis,
tenosynovitis or other musculoskeletal disorders. The following symptoms may
appear in the hands, wrists, arms, shoulders, neck or back:
•
numbness, or a burning or tingli
aching, soreness or tenderness
•
•
pain, swelling or throbbing
stiffness or tightness
•
•
coldness or weakness
If you have
and/or pain related to computer use, consult a physician immediately and
inform your company's health and safety department.
The following section provides tips for more comfortable computer use.
these symptoms, or any other recurring or persistent discomfort
mplain of eyestrain and headaches after prolonged use.
for power management:
user inactivity.
mode within 30 minutes of user inactivity.
m Sleep mode by pushing the power button.
table use
ng sensation
Finding your comfort zone
Find your comf
footrest, or raising your sitting height to achieve maximum comfort. Observe
the following tips:
•
refrain from staying too long in one fix
•
avoid slouching forward and/or
• stand up and walk around regularly to remove the strain on your leg
muscles
ort zone by adjusting the viewing angle of the monitor, using a
ed posture
leaning backward
Page 9
Taking care of your vision
Long viewing hours
room lighting, poorly focused screens, very small typefaces and low-contrast
displays could stress your eyes. The following sections provide suggestions on
how to reduce eyestrain.
Eyes
•
Rest your eyes frequently.
• Give your eyes regular breaks by looking away from the m
focusing on a distant point.
•
Blink frequently to keep your eyes fro
Display
Keep your display clean.
•
Keep your head at a higher level than the to
•
eyes point downward when looking at the middle of the display.
Adjust the display brightness and
•
enhanced text readability and graphics clarity.
Eliminate glare and re
•
•
placing your display in such a way that the side faces the window or
any light sour
minimizing room light by using dr
•
using a task light
•
•
cha
using a glare-reduction filter
•
using a display visor, such
•
display's top front edge
•
Avoid adjusting your display to a
Av
•
look
oid
periods of time.
, wearing incorrect glasses or contact lenses, glare, excessive
onitor and
m drying out.
p edge of the display so your
/or contrast to a comfortable level for
flections by:
ce
apes, shades or blinds
nging the display'
at
ing
bright ligh
s viewing angle
as a piece of cardboard extended from the
n awkward viewing angle.
t sources, such as open windows, for extended
ix
Developing good work habits
Develop the following work habits to make your com
and productive:
Take short breaks regularly and often.
•
•
Perform some stretching exercises.
• Breathe fresh air as often as possible.
Exercise regularly and maintain a health
•
y body.
puter use more relaxing
Page 10
Acer Incorporated
New Taipei City 221, Taiwan
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi
Declaration of Conformity
We,
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan
Contact Person: Mr. RU Jan, e-mail:[email protected]
And,
Acer Italy s.r.l
Via Lepetit, 40, 20020 Lainate (MI) Italy
Tel: +39-02-939-921 ,Fax: +39-02 9399-2913
www.acer.it
Declare under our own responsibility that the product:
Product: LCD Monitor
Trade Name: Acer
Model Number: B286HK
SKU Number: B286HK xxxxxx;
To which this declaration refers conforms to the relevant standard or other standardizing documents:
(“x” = 0~9, a ~ z, A ~ Z, or blank)
EN 55022:2006/A1:2007 Class B; EN 55024:2010
EN 61000-3-2:2006+A1:2009+A2:2009, Class D
EN61000-3-3:2008
EN 60950-1:2006/A11:2009/A1:2010 +A12:2011
EN50581:2012
We hereby declare above product is in com pliance w ith the essential requirem ents and other relevant
provisions of EMC Di rective 200 4/108/EC, Low Voltage Directive 2006/95/EC, and RoHS Directive
2011/65/EU and Directive 2009/125/EC with regard to establishing a framework for the setting of ecodesign
requirements for energy-related product.
Year to begin affixing CE marking 2013.
_______________________________
RU Jan / Sr. Manager Date
Regulation, Acer Inc.
Feb.17 , 2013
Page 11
Acer America Corporation
333 West San Carlos St., Suite 1500
Tel : 254-298-4000
Fax : 254-298-4147
www.acer.com
San Jose, CA 95110, U. S. A.
Federal Communications Commission
Declaration of Conformity
This device com plies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device ma y not cause harmful in terference, and (2)
this device m ust accept any interferen ce receiv ed, incl uding interference that may
cause undesired operation.
The following local Manufacturer /Importer is responsible for this declaration:
Product: LCD Monitor
Model Number:
SKU Number: B286HK xxxxxx ;
(“x” = 0~9, a ~ z, A ~ Z or Blank)
Name of Responsible Party: Acer America Corporation
Address of Responsible Party: 333 West San Carlos St.
San Jose, CA 95110
U. S. A.
Contact Person: Acer Representative
Phone No.: 254-298-4000
Fax No.: 254-298-4147
B286HK
Suite 1500
Page 12
Special notes on LCD monitors iii
Information for your safety and comfort iii
Safety instructions iii
Cleaning your monitor iii
Connecting/disconnecting the device iii
Accessibility iv
Safe listening iv
Warnings iv
Using electrical power iv
Product servicing v
Additional safety information vi
IT equipment recycling information vi
Disposal instructions vii
LCD pixel statement vii
Tips and information for comfortable use viii
Federal Communications Commission
Declaration of Conformity xi
Unpacking 1
Attaching/removing the base 2
Screen position adjustment 2
Connecting the power cord 5
Power saving
Display Data Channel (DDC)
Connector pin assignment
Standard timing table
Installation
User controls
How to adjust a setting
10
11
Acer eColor Management 12
User 13
Troubleshooting 15
HDMI mode
15
DVI mode 16
DP mode
16
1
5
5
6
8
9
Page 13
1
Unpacking
Please check that the following items are present when you unpack the box,
and save the packing materials in case you need to ship or transport the
monitor in the future.
LCD monitor Quick start guide
HDMI Cable
(Optional)
DVI cable (Option)
DP cable
(Option)
AC power cord
English
Audio Cable (Option)
MHL cable
(Optional)
MHL
(Option)USB cable
MiniDP-MiniDP
cable
(optional)
Page 14
2
ATTACHING/REMOVING THE BASE
ATTACHING/REMOVING THE BASEATTACHING/REMOVING THE BASEATTACHING/REMOVING THE BASEATTACHING/REMOVING THE BAS
Install: Align the base with the stand and push the base towards the top of
English
the monitor, and then rotate the base clockwise. Tighten the screw clockwise.
Remove: Reverse the steps to remove the base.
E
Page 15
3
SCREEN POSITION ADJUSTMENTSCREEN POSITION ADJUSTMENT
SCREEN POSITION ADJUSTMENT
SCREEN POSITION ADJUSTMENTSCREEN POSITION ADJUSTMENT
In oder to optimize the best viewing position, you can adjust the height/tilt/
swivel/pivot of the monitor.
•
•
•
After pressing the top of the monitor
•
•
•
Please see the illustration below for an example of the tilt range.
Only at the highest point can 35 degrees of recline be offered for the angle of elevation.
He ight Adjustm ent
gh t Adjustment
He ight Adjustm ent
He ight Adjustm entHe ight Adjustm ent
He i
Ti l tTi l t
Ti l t
tliT tliT
then you can adjust the height of the monitor.
1
2
mm
150
English
o
o
5
35
Page 16
4
•
•
•
With the built-in pedestal, you can swivel the monitor for the most
comfortable viewing angle.
English
•
•
•
Before rotating the display,lift it to the top position
and then push it back to the utmost degree.
Rotate clockwise until the monitor stops at 90°.
Sw i vel
Monitor PivotMonitor Pivot
Monit o r Pivot
Monitor PivotMonitor Pivot
leviwS leviwS
leviwS leviwS
o
60
60
150
90
o
Page 17
5
Connecting the power cord
• Check first to make sure that the power cord you use is the correct type
required for your area.
• The monitor has a universal power supply that allows operation in either
100/120 V AC or 220/240 V AC voltage area. No user-adjustment is
required.
• Plug one end of the power cord to the AC inlet, and plug the other end
into an AC outlet.
• For units using 120 V AC:
Use a UL-listed cord set, type SVT wire and plug rated 10 A/125 V.
• For units using 220/240 V AC:
Use a cord set consisting of H05VV-F cord and plug rated 10 A/250 V. The
cord set should have the appropriate safety approvals for the country in
which the equipment will be installed.
Power saving
The monitor will be switched to "power saving" mode by the control signal
from the display controller, as indicated by the amber-colored power LED.
Mode LED light
On Blue
Power saving Amber
English
The power saving mode will be kept until a control signal has been detected or
the keyboard or mouse is activated. The recovery time from "power saving"
mode back to "on" is around 3 seconds.
Display Data Channel (DDC)
To make installation easier, so long as your system supports the DDC protocol,
the monitor is able to plug-and-play. The DDC is a communication protocol
through which the monitor automatically informs the host system about its
capabilities; for example, supported resolutions and corresponding timing. The
monitor supports the DDC2B standard.
Page 18
English
6
Connector pin assignment
19-pin Color Display Signal cable*
13151719
12141618
PIN No. Description PIN No. Description
1 TMDS Data2+ 2 TMDS Data2 Shield
3 TMDS Data2– 4 TMDS Data1+
5 TMDS Data1 Shield 6 TMDS Data1–
7 TMDS Data0+ 8 TMDS Data0 Shield
9 TMDS Data0– 10 TMDS Clock+
11 TMDS Clock Shield 12 TMDS Clock–
13 CEC 14 Reserved (N.C. on device)
15 SCL 16 SDA
17 DDC/CEC Ground 18 +5V Power
19 Hot Plug Detect
* only for certain models
1357911
810 462
Page 19
6
English
20-pin color Mini-DP cable*
PIN No. Description PIN No. Description
1
2
3
4
5
6
7
8
9
10
Lane0(p)
GND
Lane0(n)
Lane1(p)
GND
Lane1(n)
Lane2(p)
GND
Lane3(n)
Lane3(p)
11
12
13
14
15
16
17
18
19
20
GND
Lane3(n)
Config1
Config2
AUX_CH (n)
GND
AUX_CH (p)
Hot Plug Detect
DP Power_Return
DP Power
* only for certain models
Page 20
24-pin color display signal cable*
PIN No. Description PIN No. Description
1 TMDS data 2- 13 NC
2 TMDS data 2+ 14 +5 V power
3 TMDS data 2/4 shield 15 GND (return for +5 V hsync.vsync)
4 NC 16 Hot-plug detection
5NC 17TMDS data 06DDC clock 18TMDS data 0+
7 DDC data 19 TMDS data 0/5 shield
8NC 20NC
9 TMDS data 1- 21 NC
10 TMDS data 1+ 22 TMDS clock shield
11 TMDS data 1/3 shield 23 TMDS clock+
12 NC 24 DDC TMDS clock-
7
English
20-pin color display signal cable*
PIN No. Description PIN No. Description
1
2
3
4
5
6
7
8
9
10
Lane0(p)
GND
Lane0(n)
Lane1(p)
GND
Lane1(n)
Lane2(p)
GND
Lane3(n)
Lane3(p)
11
12
13
14
15
16
17
18
19
20
GND
Lane3(n)
Config1
Config2
AUX_CH (n)
GND
AUX_CH (p)
Hot Plug Detect
DP Power_Return
DP Power
* only for certain models
Page 21
8
Standard timing table
English
1 VGA 640x480@60Hz
2 VGA 640x480@72Hz
3 VGA 640x480@75Hz
4 MAC [email protected]
5 VESA 720x400@70Hz
6 SVGA 800x600@56Hz
7 SVGA 800x600@60Hz
8 SVGA 800x600@72Hz
9 SVGA 800x600@75Hz
10 MAC [email protected]
11 XGA 1024x768@60Hz
12 XGA 1024x768@70Hz
13 XGA 1024x768@75Hz
14 MAC 1152x870@75Hz
15 VESA 1152x864@75Hz
16 VESA 1280x960@60Hz
17 SXGA 1280x1024@60Hz
18 SXGA 1280x1024@75Hz
19 VESA 1280x720@60Hz
20 WXGA 1280x800@60Hz
21 WXGA+ 1440x900@60Hz
22 WSXGA+ 1680x1050@60Hz
23 FHD 1920x1080@60Hz
24 UHD 3840x2160@30Hz
25 UHD 3840x2160@60Hz
'LVSOD\3RUWDQG0LQL'3RQO\
Page 22
Installation
To install the monitor on your host system, please follow the steps below:
Steps
1 Connect the video cable
a Make sure both the monitor and computer are switched off.
b Connect the digital cable (only for dual-input models).
(1) Make sure both the monitor and computer are switched off.
(2) Connect one end of the 24-pin DVI cable to the back of the
monitor and the other end to the computer's port.
c
Connect the digital cable (only for DP or Mini-DP models).
(1) Make sure both the monitor and computer are switched off.
(2) Connect one end of the 20-pin D
monitor and the other end to the computer's port.
d
HDMI Cable (Only HDMI or MHL Input Model)
a. Make sure both the monitor and computer are powered-OFF.
b. Connect th
e HDMI or MHL cable to the computer.
2 Connect the power cord
Connect the power cord to the monitor, then to a properly grounded AC
outlet.
Connect the
3
Connect the
USB Cable(Optional)
USB 3.0 cable to port for fast charge.
Connect the USB 3.0 cable to port.
Optional:Connect the audio input socket(AUDIO IN) of the LCD monitor
4
and the line-out port on the computer with the audio cable.
5
Turn on the monitor and computer
Turn on the monitor first, then the computer. This sequence is very
important.
6
If the monitor does not function properly, please refer to the
troubleshooting section to diagnose the problem.
P cable or Mini-DP cable to the back of the
9
English
USB
USB
2
Page 23
USER CONTROLS
Power Switch / Power LED:
To tu
rn the monitor ON or OFF.
Lights up to indicate the power is turned ON.
Using the Shortcut Menu
Press the function button to open the shortcut menu. The shortcut menu lets you
quickly select the most commonly accessed settings.
Empowering:
Press the Empowering Key to open the Acer eColor Management OSD and access
the scenario modes.
PIP (picture in picture hotkey)
Use the PIP hotkey to active the picture-in-picture function.
MENU OSD
Press this botton to activate the OSD menu.
functi
ons
NPUT Input
I
Use In
your
(a) HDMI
As you cycle through the sources you will see the following messages on right top
side of screen to indicate currently selected input source. It may take 1 or 2
seconds for the image to appear.
HDMI or DVI or DP
If either DVI input is selected ,but the DVI cables are not connected, a floating dialog box indicates:
“No Cable Connect” or “No Signal”
ut key to select from different video sources that may be connected to
p
monitor.
Key
i
nput (b) DVI input (c) DP input
or Mini-DP
(d) Mini-DP
EN-13
Page 24
Acer eColor Management
Operation instructions
Step 1: Press “ “ Key to open the Acer eColor Management OSD and
access the scenario modes
Step 2:Press “ “ or “ ” to select the mode
Step 3:Press “ “ Key to confirm the mode and exit the eColor menu.
Features and Benefits
Main
Menu
icon
Sub
Menu
icon
N/AUser mode
N/A
N/A
N/A
N/A
Sub
Menu
item
mode
ECO
Standard
mode
Grahpic
mode
Movie
mode
Description
User defined. Settings can be fine-tuned to
suit any situation
Adjusts the
settings to reduce power
consumption.
Default Setting. Reflects native display
capability
Enhances colors and emphasize fine detail.
Pictures and photographs appear in vibrant
colors with sharp detail.
Displays scenes in clearest detail. Presents
great visuals, even in unsuitably-lit
environments.
EN-14
Page 25
Adjusting the OSD settings
--------------------------------------------------------------------
Note: The following content is for general reference only. Actual
product
The OSD can be used for adjusting the settings of your LCD Monitor.
Press the MENU key to open the OSD. You can use the OSD to adjust the
picture quality, OSD position and general settings. For advanced settings,
please refer to following page:
Adjusting the picture quality
specifications may vary.
1Press the MENU key to bring up the OSD.
2Using the
the picture element you wish to adjust.
3Use the / keys to adjust the sliding scales.
/ keys, select Picture from the OSD. Then navigate to
4 ThePicturemenucanbeusedtoadjusttheBrightness,Contrast,ColourTemp,
6‐axisSaturation,6‐axisHueandotherimage‐relatedqualities.
5 6‐axis Saturate: Adjust saturation of red, green, blue, yellow, magenta and
cyan6‐axisHue:Adjusthueforred,green,blue,yellow,magentaandcyan.
Super Sharpness technology can simulate high-resolution images by boosting
6
the pixel density of the original source. It can make the image more sharper
and clear.
7
DPmodeselection,the default out of DP signal settingin B286HK
is
DP1.2.Usercan follow the setting message to confirm selection of
DP1.2 or DP1.1
EN-15
Page 26
Adjusting the OSD position
1
Press the MENU key to bring up the OSD.
Using the directional keys,
2
Then navigate to the
select
feature you wish to adjust.
OSD from the on screen display.
EN-16
Page 27
Adjusting the setting
1Press the MENU key to bring up the OSD.
2Using the / keys, select Setting from the OSD. Then navigate to
the feature you wish to adjust.
3The Setting menu can be used to adjust the screen Menu Language and
other important settings.
Select Power-off USB charge ON/OFF to enable/disable Power-off USB
4
charge function.
5 SelectPIPtoadjustpicture‐in‐picturesettings.ThePIPsignal
sourceneedsto
beselectedmanually.
6
When using PIP, "Wide mode",
display.
7
"Wide mode" is not supported when
"ACM" will be enabled for the main source
using PBP function.
EN-17
Page 28
Product information
1Press the MENU key to bring up the OSD.
2Using the / keys, select Information from the OSD. Then the
basic information of LCD monitor will show up for current input.
EN-18
Page 29
Troubleshooting
Before sending your LCD monitor for servicing, please check the
troubleshooting list below to see if you can self-diagnose the problem.
DVI / HDMI mode
Problem LED status Remedy
No picture visible Blue Using the OSD, adjust brightness and
contrast to maximum or reset to their
default settings.
Off Check the power switch.
Check if the AC power cord is properly
connected to the monitor.
Amber Check if the video signal cable is
Problem LED status Remedy
No picture visible Blue Using the OSD, adjust brightness and
Off Check the power switch.
properly connected at the back of
monitor.
Check that the computer system is
switched on and in power saving/
standby mode.
contrast to maximum or reset to their
default settings.
Check if the AC power cord is properly
connected to the monitor.
Amber Check if the video signal cable is
properly connected at the back of
monitor.
Check that the computer system is
switched on and in power saving/
standby mode.
Loading...