Acer T230H User Manual

T230H

Safety Instructions

Observe the following safety guidelines when connection and using your monitor:

y Be sure that your monitor is electrically rated to operate with the AC power available in your location.
y Locate your monitor near an easily accessible electrical outlet.
y Place the monitor on a solid surface and treat it carefully. The screen can be damaged if dropped,

sharply hit, or touched with a sharp or abrasive implement.

y Put your monitor in a location with low humidity and a minimum of dust.
y Never use your monitor if the power cable has been damaged. Do not allow anything to rest on the

power cable, and keep the cable away from where people could trip over it.

y Never insert anything metallic into the monitor openings. Doing so may create the danger of electric shock.
y To avoid electric shock, never touch the inside of the monitor. Only a qualified technician should open

the monitor's case.

y Be sure to hold the plug, not the cable, when disconnecting the monitor from an electrical outlet.
y Openings in the monitor cabinet are provided for ventilation. To prevent overheating, these openings

should not be blocked or covered. Also, avoid using the monitor on a bed, sofa, rug, or other soft surface.

y Doing so may block the ventilation openings in the bottom of the cabinet. If you put the monitor in a

bookcase or some other enclosed space, be sure to provide adequate ventilation.

y Do not expose the monitor to rain or use it near water. If the monitor accidentally gets wet, unplug it and

contact an authorized dealer immediately. You can clean the exterior of the monitor with a damp cloth
when necessary, but be sure to unplug the monitor first. If your monitor does not operate normally-in
particular, if there are any unusual sounds or smells coming from it -unplug the monitor immediately and
contact an authorized dealer or service center.

y Please move the power cable before the products are maintained.
y

Connecting Your Monitor to a Computer

Make sure both the monitor and computer are powered-OFF.

1. 1-1 Connect Video Cable
Connect the VGA video cable to the computer.
1-2 Connect Digital Cable

Connect one end of the 24-pin DVI cable to the back
of the monitor and connect the other end to the

computer's port.
1-3 Connect HDMI Cable
Connect the HDMI cable to the computer.
1-4 Connect Audio Cable
Connect the Audio cable to the computer.

1-5 Connect USB Cable

Connect the USB cable to the computer.

Connect one end of the USB cable to the back of the
monitor and the other end to the computer's port.
Connect power cord

2.

Connect the power cord to the monitor, then to a properly
grounded AC outlet.
Power-ON Monitor and Computer

3.

Power-ON the monitor first, then power-ON the computer.
This sequence is very important.
If the monitor still does not function properly, please refer

4.

to the troubleshooting section to diagnose the problem.

Troubleshooting Tips
No Power - The monitor's power indicator is off.

z Make sure the monitor power cable is fully inserted in the monitor's power port and the electrical outlet.
z Test the electrical outlet by plugging in a working electrical device such as a lamp.
z Try another power cable on the monitor. You can use the computer's power cable to perform this test.

No Video - The monitor's power indicator is on but there is no image on the screen.

z Ensure that the video connector is properly connected to the computer.
z Ensure that the computer is on and functioning properly.
z Turn off the monitor and check the video cable pins. Make sure no pins are bent.

Operating Detail

z Please refer to user's guide in CD-ROM packaged with this monitor

English

LCD Monitor Quick Setup Guide

Regulations and safety notices

FCC notice

T230H

English

This device has been tested and found to comply with the limits for a Class B digital device
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This device generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
device does cause harmful interference to radio or television reception, which can be
determined by turning the device off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

CE declaration of Conformity

Hereby, Acer Inc., declares that this LCD monitor is in compliance with the essential
requirements and other relevant provisions of EMC Directive 89/336/EEC, amended by
92/31/EEC and 93/68/EEC, Low Voltage Directive 2006/95/EC, and RoHS Directive
2002/95/EC.

Notice: Shielded cables

y Reorient or relocate the receiving antenna.
y Increase the separation between the device and receiver.
y Connect the device into an outlet on a circuit different from that to which the receiver is

connected.

y Consult the dealer or an experienced radio/television technician for help.

All connections to other computing devices must be made using shielded cables to maintain
compliance with EMC regulations.

Notice: Peripheral devices

Only peripherals (input/output devices, terminals, printers, etc.) certified to comply with the
Class B limits may be attached to this equipment. Operation with non-certified peripherals is
likely to result in interference to radio and TV reception.

Caution

Changes or modifications not expressly approved by the manufacturer could void the user
authority, which is granted by the Federal Communications Commission, to operate this
product.

Operation conditions

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.

Notice: Canadian users

This Class B digital apparatus complies with Canadian ICES-003.

Remarque a I'intention des utilisateurs canadiens

Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada.

LCD Monitor Quick Setup Guide