ACER M190PW01 V8 Specification
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
M190PW01 V8
( ) Preliminary Specification
(V ) Final Specification
Module 19” WXGA+ Color TFT-LCD
Model Name M190PW01 V8
Customer Date
Approved by
Approved by Date
ChiYi Wu
Prepared by Date
Nov 9, 2011
Note: This Specification is subject to
change without notice.
document version 1.0 1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Arnold Hsu
Desktop Display Business Group /
AU Optronics corporation
Nov 9, 2011
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
M190PW01 V8
Contents
1.0 Handling Precautions............................................................. 4
2.0 General Description ............................................................... 5
2.1 Display Characteristics.................................................................................................................... 5
2.2 Optical Characteristics ....................................................................................................................6
3.0 Functional Block Diagram .................................................... 10
4.0 Absolute Maximum Ratings......................................................... 11
4.1 TFT LCD Module..............................................................................................................................11
4.2 Backlight Unit.................................................................................................................................... 11
4.3 Absolute Ratings of Environment ...................................................................................................... 11
5.0 Electrical characteristics...................................................... 12
5.1 TFT LCD Module............................................................................................................................ 12
5.1.1 Power Specification.............................................................................................. 12
5.1.2 Signal Electrical Characteristics.............................................................................. 13
5.2 Backlight Unit.................................................................................................................................... 14
6.1 Pixel Format Image........................................................................................................................15
6.2 The input data format .................................................................................................................... 15
6.3 Signal Description.......................................................................................................................... 16
6.4 Timing Characteristics ....................................................................................................................... 18
6.5 Timing diagram............................................................................................................................... 19
6.6 Power ON/OFF Sequence ...........................................................................................................20
7.0 Connector & Pin Assignment ............................................... 21
7.1 TFT LCD Module............................................................................................................................ 21
7.1.1 Pin Assignment ................................................................................................... 21
7.2 Backlight Unit.................................................................................................................................. 22
8.0 Reliability Test..................................................................... 23
9.0 Shipping Label ..................................................................... 24
10. Packing Specification........................................................... 25
11.0 Mechanical Characteristics ................................................ 26
document version 1.0 2
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
M190PW01 V8
Record of Revision
Version and Date Page Old description New Description Remark
0.1 2010/11/15 All First Edition for Customer N/A
1.0 2011/11/09 22
document version 1.0 3
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
M190PW01 V8
1.0 Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth
when handling.
7) Do not open or modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was taken
out from the container, do not press the center of the LED lightbar edge. Instead, press at the
far ends of the LED light bar edge softly. Otherwise the TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module
even momentary. At designing the enclosure, it should be taken into consideration that no
bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT
Module may be damaged.
12) Small amount of materials having no flammability grade is used in the LCD module. The LCD
module should be supplied by power complied with requirements of Limited Power Source
(IEC60950 or UL1950), or be applied exemption.
13) Pls avoid touching COF position while you are doing mechanical design
14) When storing modules as spares for a long time, the following precaution is necessary:
Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep
the temperature between ˈкʳ ˴˷ʳˆˈкʳ ˴ʳ˴˿ʳ˻˼˷˼ˁ
document version 1.0 4
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
M190PW01 V8
2.0 General Description
This specification applies to the 19 inch-wide Color TFT-LCD Module M190PW01.
The display supports the WXGA+ (1440(H) x 900(V)) screen format and 16.7M colors(RGB
6-bits+HiFRC). All input signals are 2-Channel LVDS interface compatible. This module does
not contain an inverter board for backlight.
2.1 Display Characteristics
The following items are characteristics summary on the table under 25к condition:
ITEMS Unit SPECIFICATIONS
Screen Diagonal [mm]
Active Area [mm] 408.24 (H) x 255.15(V)
Pixels H x V 1440x3(RGB) x 900
Pixel Pitch [um] 283.5 (per one triad) ×283.5
Pixel Arrangement R.G.B. Vertical Stripe
Display Mode TN Mode, Normally White
White Luminance ( Center ) [cd/m2]
Contrast Ratio 1000 (Typ.)
Optical Response Time [msec] 5ms (Typ., on/off)
Nominal Input Voltage VDD [Volt] +5.0 V
Power Consumption
[Watt]
(VDD line + LED line)
Weight [Grams] 1450 (Typ)
Physical Size [mm] 428.0(W) x 278.0(H) x 10.3(D) (Typ)
Electrical Interface Dual channel LVDS
Support Color 16.7M colors (RGB 6-bit + Hi_FRC )
Surface Treatment Anti-Glare, 3H
Temperature Range
Operating
Storage (Shipping)
o
[
C]
o
[
C]
RoHS Compliance RoHS Compliance
TCO5.1 Compliance TCO5.1 Compliance
481.4(18.9”)
2
250 cd/m
15.1W (Typ)
(Typ.)
(without inverter, all black pattern)
0 to +50
-20 to +60
document version 1.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
5
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
M190PW01 V8
AU OPTRONICS CORPORATION
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25к:
Item Unit Conditions Min. Typ. Max. Note
Horizontal (Right)
CR = 10 (Left)
Viewing Angle [degree]
Vertical (Up)
CR = 10 (Down)
Contrast ratio Normal Direction
Raising Time (TrR)
Falling Time (TrF)
Response Time [msec]
Raising + Falling
Gray to Gray(16x16 avg.)
Red x
Red y 0.315 0.345 0.375
Color / Chromaticity
Coordinates (CIE)
Green x 0.291 0.321 0.351
Green y 0.595 0.625 0.655
Blue x 0.121 0.151 0.181
Blue y 0.027 0.057 0.087
Color Coordinates (CIE) White
White x
White y
Central Luminance [cd/m2] 200 250 - 6
Luminance Uniformity
Crosstalk (in 75 Hz)
Flicker
[%]
[%]
dB
70
70
70
70
600
0.612 0.642 0.672
0.283 0.313 0.343
0.299 0.329 0.359
75 80
85
-
-
85
80
-
-
80
1000 -
-
-
-
-
3.6 5.7
1.4 2.3
5 8
- -
-
1.5 8
-20
2
3
4
5
7
9
document version 1.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
6
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
M190PW01 V8
Note 1: Measurement method
The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt
temperature change during measuring (at surface 35
. In order to stabilize the luminance, the
measurement should be executed after lighting Backlight for 30 minutes in a stable, windless and
dark room. ʳ
Photo detector
Measured distance
LCD Panel
Center of the screen
Note 2: Definition of viewing angle measured by ELDIM (EZContrast 88)
Viewing angle is the measurement of contrast ratio Њ10, at the screen center, over a 180°
horizontal and 180° vertical range (off-normal viewing angles). The 180° viewing angle range is
broken down as follows; 90° (θ) horizontal left and right and 90° (Φ) vertical, high (up) and low
(down). The measurement direction is typically perpendicular to the display surface with the screen
rotated about its center to develop the desired measurement viewing angle.
TFT-LCD Module
document version 1.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
7
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Loading...