05 Spare Parts List ...................................................................................................41
06 Schematics and Layouts.......................................................................................42
07 Assembly and Disassembly ................................................................................49
Appendix : User’s manual
Copyright
Copyright 2006 InnoLux Tech. Corp. Ltd
All Rights Reserved
This manual may not, in whole or in part, be copied, Photocopied, reproduced, translated, or converted to any
electronic or machine readable form without prior written permission of InnoLux Tech. Corp. Ltd.
Acer X163W Service Manual
1
Acer Acer –LCD-X163W
Important Safety Notice
1. Safety precautions
This monitor is manufactured and tested on a ground principle that a user’s safety comes first. However,
improper used or installation may cause damage to the monitor as well as to the user.
Warning:
zThis monitor should be operated only at the correct power sources indicated on the label on the rear of the
monitor. If you’re unsure of the power supply in you residence, consult your local dealer or Power
Company.
zDo not try to repair the monitor by yourself, as it contains no user-serviceable parts. This monitor should
only be repaired by a qualified technician.
zDo not remove the monitor cabinet. There are high-voltage parts inside that may cause electric shock to
human bodies.
z Stop using the monitor if the cabinet is damaged. Have it checked by a service technician.
z Put your monitor only in a lean, cool, dry environment. If it gets wet, unplug the power cable immediately
and consult your closed dealer.
zAlways unplug the monitor before cleaning it. Clean the cabinet with a clean, dry cloth. Apply non-ammonia
based cleaner onto the cloth, not directly onto the class screen.
zDo not place heavy objects on the monitor or power cord.
2. Product safety notice
Many electrical and mechanical parts in this chassis have special safety visual inspections and the protection
afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage,
wattage, etc. Before replacing any of these components read the parts list in this manual carefully. The use of
substitute replacement parts, which do not have the same safety characteristics as specified in the parts list,
may create shock, fire, or other hazards.
3. Service notes
z When replacing parts or circuit boards, clamp the lead wires around terminals before soldering.
z Keep wires away from high voltage, high temperature components and sharp edges.
z Keep wires in their original position so as to reduce interference.
z Adjustment of this product please refers to the user’ manual.
2
Acer Acer –LCD-X163W
01 Product Specification
1. General:
Acer X163W is designed with analog interface input, it featured with embedded universal AC power supply . It’s a green
product and meets all ROHS standard. The power button and display control buttons are on the front of the monitor. The
monitors shall automatically to display lower resolution video modes into 1366 x768 full screen display. The image can be
adjusted through OSD control.
Through D-SUB connectors, this unit can support FH= 31 ~ 57 KHz, Fv=56 ~ 70Hz and panel DCLK<=
85 MHz. SXGA display modes as below:
VESA MODES
Horizontal Vertical
Nominal
Nominal
Frequency
+/-0.5KHz
640*480@60Hz 800*525 31.469 N 59.941 N 25.175
800*600@56Hz 1024*625 35.156 P 56.250 P 36.000
800*600@60Hz 1056*628 37.879 P 60.317 P 40.000
1024*768@60Hz 1344*806 48.363 N 60.004 N 65.000
1024*768@70Hz 1328*806 56.476 N 70.069 N 75.000
Sync
Polarity
Nominal
Frequency
+/-1Hz
Sync
Polarity
MAC MODES
640*480@66.7Hz
864*525
35.000 P
66.667 P 30.240
Other MODES
1024*768@66Hz
1366*768@60Hz 1792*798 47.714 P 59.790 P 85.500
1318*809
53.414
N 66.025 N 70.400
Pixel Clock
(MHz)
Note: 1. Non-interlace signals only (An interlace signal cannot be display)
2. Please refer to F/W specification for more detail
3. Each frequency of Power Macintosh and Sun Ultra is a reference value
7
Acer Acer –LCD-X163W
4.2.2 DDC signals
DDC signals: 5V@50mA TTL level
4.3 Timing requirements
Scan Frequency Condition Specification
Horizontal
Vertical
Out of range
4.4DDC data
4.4.1
EDID Standard Compliance
EDID File Format : VESA’s EDID Standard Version #3, Revision #0,
EDID Structure : Version #1, Revision #3.
EDID Data Table : See the attached table (for example)
14h Analog/Digital Signal Level [7] Analog Signal Level
Signal Level Standard [6:5] 0.700, 0.300 (1.000Vp-p)
Setup [4] No Blank -to-black Setup
8
Acer Acer –LCD-X163W
A
A
A
Sync Inputs Supported [3] Separate Syncs. Supported
Sync Inputs Supported [2] No Composite Sync. Supported
Sync Inputs Supported [1] No Sync. on Green Supported
Sync Inputs Supported [0] No Serration Required
15h
16h
17h Gamma2.2
18h VESA DPMS [7] Standby
VESA DPMS [6] Suspend
Display Off Consumption [5] Active Off/Very Low Power
Display Type [4:3] RGB Color Display
Preferred Timing Mode [1] No Preferred Timing Mode
GTF Standard [0] No Default GTF Supported
19~22h
Green (x , y) 0.290, 0.591
Blue (x , y)0.153, 0.082
Max. Horizontal Image
Size
Max. Vertical Image
Size
sRGB Standard Color Space
[2]
Red (x ,
y)
35 cm
20 cm
No sRGB Color Space
0.638, 0.333
White (x , y)0.313, 0.329
23h IBM, VGA [7] 720 x 400 @ 70Hz (N/A)
IBM, XGA2 [6] 720 x 400 @ 88Hz (N/A)
IBM, VGA [5] 640 x 480 @ 60Hz
VESA [3] 640 x 480 @ 72Hz (N/A)
VESA [2] 640 x 480 @ 75Hz (N/A)
VESA [1] 800 x 600 @ 56Hz
VESA [0] 800 x 600 @ 60Hz
24h VESA [7] 800 x 600 @ 72Hz (N/A)
VESA [6] 800 x 600 @ 75Hz (N/A)
IBM [4] 1024 x 768 @ 87Hz(I) (N/A)
VESA [3] 1024 x 768 @ 60Hz
VESA [2] 1024 x 768 @ 70Hz
pple, Mac II [4] 640 x 480 @ 67Hz
pple, MacII [5] 832 x 624 @ 75Hz (N/A)
VESA [1] 1024 x 768 @ 75Hz (N/A)
VESA [0] 1280 x 1024 @ 75Hz (N/A)
25h
pple, Mac II [7] 1152 x 870 @ 75Hz (N/A)
9
Acer Acer –LCD-X163W
VESA [6] 800 x 600 @ 85Hz (N/A)
VESA [5] 1024 x 768 @ 85Hz (N/A)
VESA [4] 1280 x 1024 @ 60Hz (N/A)
VESA [3] 1280 x 1024 @ 85Hz (N/A)
VESA [2] 1600 x 1024 @ 60Hz (N/A)
VESA [1] 1600 x 1200 @ 75Hz (N/A)
VESA [0] 1600 x 1200 @ 85Hz (N/A)
26~27h Standard Timing Identification #1 1024 x 768 @ 66Hz 4: 3
28~29h Standard Timing Identification #2 No Application
2A~2Bh Standard Timing Identification #3 No Application
2C~2Dh Standard Timing Identification #4 No Application
2E~2Fh Standard Timing Identification #5 No Application
30~31h Standard Timing Identification #6 No Application
32~33h Standard Timing Identification #7 No Application
34~35h Standard Timing Identification #8 No Application
Pixel Clock 85.86 MHz
Horizontal Active 1366 Pixels
Horizontal Blanking 432 Pixels
36~46h
Vertical Sync Pulse Width 3 Lines
Horizontal Image Size 344 mm
Vertical Image Size 193 mm
Horizontal Border 0 Pixels
Vertical Border 0 Lines
Vertical Active 768 Lines
Vertical Blanking 27 Lines
Horizontal Sync Offset 72 Pixels
Horizontal Sync Pulse Width144 Pixels
Vertical Sync Offset 1 Lines
Non-Interlaced
Normal Display, No Stereo
Flags
48~59h
Digital Separate
Vsync Positive Polarity
Hsync Negative Polarity
Min. Vertical Frequency 56 Hz
Max. Vertical Frequency 70 Hz
Min. Horizontal Frequency 31 kHz
10
Acer Acer –LCD-X163W
Max. Horizontal Frequency57 kHz
Max. Pixel Clock 90 MHz
5A~6Bh Monitor Serial Number 1234567890AB
6C~7Dh Monitor Name X163W
7Eh Extension Flag 00
7Fh Checksum 43
5. Function Specifications
All the tests to verify specifications in this section shall be performed under the following standard conditions unless
otherwise noted. The standard conditions are:
Temperature : 25 ± 5°C
Warm-up time : 30 minutes minimum
Checking display modes : All the specified modes
A. When “main OSD” un-displays, press [AUTO] to perform “scenario OSD” ;
[AUTO]
B. When “scenario OSD” displays, press [AUTO] to perform auto-adjustment;
C. When “main OSD” displays, press [AUTO] to return to previous level menu or exit
“main OSD”.
11
Acer Acer –LCD-X163W
e]
[
[MENU]
[►], [◄]
[POWER] Power on or power off the monitor
5.2.2
Hot Key Operation
FUNCTION
FACTORY
MODE
A. When OSD un-displays, when press [
B. When OSD displays, when press [
A. When “main OSD” isn’t shown on screen, press [MENU] to enter “main OSD”
interface;
B. When “main OSD” and displays, press [MENU] to perform function of menu icon that
is highlight or enter next level menu.
When “main OSD” and “scenario OSD” displays, press these keys to change the
contents of an adjustment item, or change an adjustment value
HOT KEY OPERATION
e
◄► MENUPOWER
●
●
e] the e-Color menu will show
e] the e-Color menu will show, OSD will disappear
DESCRIPTION
Press [e] & [MENU] at the same time, and then
ON
press [POWER] for DC power on. OSD menu
will be shown with “F” on the left top. Select “F”
for entering factory mode.
5.3 OSD Structure
The On-Screen Display (OSD) shall be an easy to use icon based menu through keypad OSD buttons or remote
control unit. The unit shall leave the factory with all OSD controls set to their default values.
First Second Third Control Range Default Value
50
77
Brightness
Image
Position
Color
Language
Contrast
Brightness
Focus
Clock
Horizontal
Vertical
Warm (6500K)
Cool (9300K)
User
NO-EMEA EMEA
English English
User mode
Text mode 50
---
---
---
---
---
---
0 ~ 100
0 ~ 100
0 ~ 100
0 ~ 100
0 ~ 100
0 ~ 100
Standard mode 50
Graphics mode 60
Movie mode 56
User mode
Text mode 44
Standard mode 77
Graphics mode 97
Movie mode 77
Depend on each timing
50
50
Depend on each timing
--- ---
--- ---
Red
Green
Blue
0 ~ 100
0 ~ 100
0 ~ 100
--- ---
80
80
80
English
12
Acer Acer –LCD-X163W
OSD
Input
Info
Reset
Exit
Deutsch Deutsch
Español Español
简体中文
繁體中文
Français Français
Italiano Italiano
日本語
Hor. Position
Ver. Position
OSD Timeout
Analog
Digital
Resolution
H. Freq
V. Freq
Hollands
Русский
Suomalainen
--- ---
--- ---
--- ---
--- ---
--- ---
--- ---
--- ---
---
---
---
0 ~ 100 50
0 ~ 100 50
10~ 120 20
--- --- ---
--- --- ---
--- --- ---
--- --- ---
--- --- ---
--- --- --- ---
--- --- --- ---
Notes; ○1 Clock default 50 is for Visa timing. Others depend on timing.
8.0 SOP of firmware upgrade
8.1 Operational condition:
Equipment: PC, ISP card, signal cable and power cable.
ESD requirements: antistatic wrists, antistatic gloves (fingers), and connecting cable
Name of ISP program:
Manufacture of FW IC
ISP_Tool_v3.7.5.3
:
PMC/SST/MX
8.2 Operational steps:
1. Connection: connect PC to PCBA with signal cable, and then keep AC and DC in open state.
One port of ISP
program card
is connected to
PC print port.
13
Acer Acer –LCD-X163W
2. Adjust ISP programming
Firstly, double click ISP_Tool_v3.7.5EXEI and open ISP program, then select “Device”, next select
manufacturer model of FW IC, which should be correspondent with that of PCBA FW IC. Double click
Figure One.
Secondly﹐download FW software: first select “READ”, and then load FW software in Rooter (Fig.2).
FW software
rooter
Software
Checksum
Thirdly, select “Connect” and enter ISP MODE as in the following Figure 3.
14
Acer Acer –LCD-X163W
Fourthly, select “AUTO”, and keep its default value. Click “RUN” for beginning programming. There will
be prompting if programming is OK.
Note: if programming fails or success rate is not high, click “Config” and adjust its speed in
“E2PROM DEVICE SETTING”
15
Acer Acer –LCD-X163W
prog
K
After connecting, AC ON,
DC ON
OK
Open ISP program
OK
Choose manufacturer
and model of FW IC
OK
LOAD FW software
OK
Click Connect and enter
ISP MODE
OK
◆Flowing chart
Click AUTO and RUN for
beginning programming
OK
Turn off power if
ramming is O
NG
16
Choose Config
and adjust
programming
Loading...
+ 39 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.