Acer FT220HQL User Manual

Acer LCD Monitor
User's Guide
Copyright © 2013. Acer Incorporated. All Rights Reserved.
Acer LCD Monitor User's Guide Origi
nal Issue: 09/20
Changes may be made periodically to the information in this publication without obligation to notify any person of such revisions or changes. Such changes will be incorporated in new editions of this manual or supplementary documents and publications. This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims the implied warranties of merchantability or fitness for a particular purpose.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronically, mechanically, by photocopy, recording or otherwise, without the prior written permission of Acer Incorporated.
13
Acer LCD Monitor User's Guide
Model number: __________________________________
Serial number: ___________________________________
Date of purchase: ________________________________
Place of purchase: ________________________________
Acer and the Acer logo are registered trademarks product names or trademarks are used herein for identification purposes only and belong to their respective companies.
of Acer Incorporated. Other companies'
Special notes on LCD monitors
The following are normal with the LCD m
Due to the nature of the fluorescent ligh
initial use. Turn off the power switch and then turn it on again to make sure the flicker disappears.
You may find slightly uneven br
desktop pattern you use. The LCD screen has 99.99% or more effective pixe
blemishes of 0.01% or less such as a missing pixel or a pixel lit all the time. Due to the nature of the LCD screen, an afterimage of the previous screen
may rema for hours. In this case, the screen is recovered slowly by changing the image or turning off the power switch for a few hours.
in after switching the image, when the same image is displayed
onitor and do not indicate a problem.
t, the screen may flicker during
ightness on the screen depending on the
ls. It may include
Information for your safety and comfort
Safety instructions
iii
Read these instructions carefu Follow all warnings and instructions marked on the product.
lly. Keep this document for future reference.
Cleaning your monitor
Please carefully follow these guidelines wh
Always unplug the monitor befo Use a soft cloth to wipe the screen and cabin
en cleaning the monitor:
re cleaning.
et front and sides.
Connecting/disconnecting the device
Observe the following guidelines when connecting and disconnecting power from the LCD monitor:
Make sure the monitor is attached to its base before conn
cord to the AC power outlet.
Make sure both the LCD monitor and th connecting any cable or unplugging the power cord.
If the system has multiple sources o
system by unplugging all power cords from the power supplies.
e computer are turned off before
f power, disconnect power from the
ecting the power
iv
Accessibility
Be sure that the power outlet you plug the power cord into is easily accessible and located
as close to the equipment operator as possible. When you need to disconnect power from the equipment, be sure to unplug the power cord from the electrical outlet.
Safe listening
To protect your hearing, follow these instructions.
Gradually increase the volume until you can hear it clearly and comfortably
and without distortion. After setting the volume level, do not increase it after your ears have
adjusted. Limit the amount of time listening to music at high volume.
Avoid turning up the volume to block out noisy surroundings.
Turn the volume down if you can't hear people speaking near you.
Warnings
Do not use this product near water.
Do not place this product on an unstable cart, stand or table. If the product falls, it could be seriously damaged.
Slots and openings are provided for ventilation to ensure reliable
operation of the product and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should never be placed near or over a radiator or heat register, or in a built-in installation unless proper ventilation is provided.
Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind onto or into the product.
To avoid damage of internal components and to prevent battery leakage,
do not place the product on a vibrating surface. Never use it under sporting, exercising, or any vibrating environment
which will probably cause unexpected short current or damage internal devices.
Your device uses one of the following power supplies:
Object/ Manufacturer/ Type/
Part No. Trademark Model
P
ower
Adapt
DELTA
er
APD
Meikai
ADP-65JH DB ADP-65VH D
DA-50F19
PDN-65B-18
Using electrical power
This product should be operated from the type of power indicated on the
marking label. If you are not sure of the type of power available, consult your dealer or local power company.
Do not allow anything to rest on the power cord. Do not locate this
product where people will walk on the cord.
If an extension cord is used with this product, make sure that the total
ampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure that the total rating of all products plugged into the wall outlet does not exceed the fuse rating.
Do not overload a power outlet, strip or receptacle by plugging in too
many devices. The overall system load must not exceed 80% of the branch circuit rating. If power strips are used, the load should not exceed 80% of the power strip's input rating.
This product's power cord is equipped with a three-wire grounded plug.
The plug only fits in a grounded power outlet. Make sure the power outlet is properly grounded before inserting the power cord plug. Do not insert the plug into a non-grounded power outlet. Contact your electrician for details.
Warning! The grounding pin is a safety feature. Using a power outlet that is not properly grounded may result in electric shock and/or injury.
Note: The grounding pin also provides good protection from unexpected noise produced by other nearby electrical devices that may interfere with the performance of this product.
Use the product only with the supplied power supply cord set. If you need
to replace the power cord set, make sure that the new power cord meets the following requirements: detachable type, UL listed/CSA certified, type SPT-2, rated 7 A 125 V minimum, VDE approved or its equivalent, 4.5 meters (15 feet) maximum length.
v
Product servicing
Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks. Refer all servicing to qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service personnel when:
the power cord or plug is damaged, cut or frayed
liquid was spilled into the product
the product was exposed to rain or water
the product has been dropped or the case has been damaged
the product exhibits a distinct change in performance, indicating a need for service
the product does not operate normally after following the operating
instructions
vi
Note: Adjust only those controls that are covered by the operating instructions, since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal condition.
Potentially explosive environments
Switch off your device in any area with a potentially explosive atmosphere and obey all signs and instructions. Potentially explosive atmospheres include areas where you would normally be advised to turn off your vehicle engine. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death. Switch off the device near gas pumps at service stations. Observe restrictions on the use of radio equipment in fuel depots, storage and distribution areas; chemical plants; or where blasting operations are in progress. Areas with a potentially explosive atmosphere are often, but not always, marked. They include below deck on boats, chemical transfer or storage facilities, vehicles using liquefied petroleum gas (such as propane or butane), and areas where the air contains chemicals or particles such as grain, dust or metal powders.
Additional safety information
Your device and its enhancements may contain small parts. Keep them out of the reach of small children.
IT Equipment Recycling Information
Acer is strongly committed to environmental protection and views recycling, in the form of salvaging and disposal of used equipment, as one of the company's top priorities in minimizing the burden placed on the environment.
We at Acer are very conscious of the environmental effects of our business and strive to identify and provide the best working procedures to reduce the environmental impact of our products.
For more information and help when recycling, please go to this website:
http://www.acergroup.com/public/Sustainability/
Visit www. .com of our other products.
acer-group
for further information on the features and benefits
vii
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please recycle. For more information on the Waste from Electrical and Electronics Equipment (WEEE) regulations, visit
http://www.acergroup.com/public/Sustainability
LCD pixel statement
The LCD unit is produced with high-precision manufacturing techniques. Nevertheless, some pixels may occasionally misfire or appear as black or red dots. This has no effect on the recorded image and does not constitute a malfunction.
viii
This product has been shipped enabled for po
Activate display’s Sleep mode within 15 minutes of user inac
Activate computer’s Sleep mo
Wake the computer from
Sleep mode by pushing the power button.
wer management:
tivity.
de within 30 minutes of user inactivity.
Tips and information for comfortable use
Computer users may comp Users are also at risk of physical injury after long hours of working in front of a computer. Long work periods, bad posture, poor work habits, stress, inadequate working conditions, personal health and other factors greatly increase the risk of physical injury.
Incorrect computer usage may lead to carpal tunnel syndrome, tendonitis, tenosynovitis or other musculoskeletal disorders. The following symptoms may appear in the hands, wrists, arms, shoulders, neck or back:
numbness, or a burning or tingling sen aching, soreness or tenderness
pain, swelling or throbbing stiffness or tightness
coldness or weakness If you have t and/or pain related to computer use, consult a physician immediately and inform your company's health and safety department.
The following section provides tips for more comfortable computer use.
hese symptoms, or any other recurring or persistent discomfort
Finding your comfort zone
Find your comfort zo footrest, or raising your sitting height to achieve maximum comfort. Observe the following tips:
refrain from staying too long in one fixe
avoid slouching forward and/or leanin
stand up and walk around regularly to remove the strain on your leg
muscles
lain of eyestrain and headaches after prolonged use.
sation
ne by adjusting the viewing angle of the monitor, using a
d posture
g backward
Taking care of your vision
Long viewing hours, wea room lighting, poorly focused screens, very small typefaces and low-contrast displays could stress your eyes. The following sections provide suggestions on how to reduce eyestrain.
Eyes
Rest your eyes frequently.
Give your eyes regular breaks by looking away from the moni
focusing on a distant point.
Blink frequently to keep your eyes from
Display
Keep your display clean.
Keep your head at a higher level than the top ed
eyes point downward when looking at the middle of the display. Adjust the display brightness and/
enhanced text readability and graphics clarity. Eliminate glare and ref
placing your display in such a way that the side faces the window or any light sourc
minimizing room light by using drapes, shad
using a task light
cha
nging the display'
using a glare-reduction filter
using a display visor, such as
display's top front edge
Avoid adjusting your display to an Av
look
oid
periods of time.
ing
ring incorrect glasses or contact lenses, glare, excessive
tor and
drying out.
ge of the display so your
or contrast to a comfortable level for
lections by:
e
es or blinds
s viewing angle
a piece of cardboard extended from the
awkward viewing angle.
at
bright ligh
t
sources, such as open windows, for extended
ix
Developing good work habits
Develop the following work habits to make your computer u and productive:
Take short breaks regularly and often.
Perform some stretching exercises.
Breathe fresh air as often as possible.
Exercise regularly and maintain a healthy b
ody.
se more relaxing
We,
Declaration of Conf
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan Contact Person: Mr. RU Jan, e-mail:ru.jan@acer.com
And,
Acer Italy s.r.l
Via Lepetit, 40, 20020 Lainate (MI) Italy Tel: +39-02-939-921 ,Fax: +39-02 9399-2913 www.acer.it
Declare under our own responsibility that the product:
Product: LCD Monitor Trade Name:
Model Number:
SKU Number:
To which this declaration refers conforms to the relevant standard or other standardizing documents:
EN55022:2006/A1:2007 Class B; EN55024:2010 EN 61000-3-2:2006+A1:2009+A2:2009, Class D EN61000-3-3:2008 EN60950-1:2006/A11:2009/A1:2010+A12:2011 EN50581:2012
We hereby declare above product is in compliance with the essential requirements and other relevant provisions of EMC Directive 2004/108/EC, Low Voltage Directive 2006/95/EC, and RoHS Directive 2011/65/EU and Directive 2009/125/EC with regard to establishing a framework for the setting of ecodesign requirements for energy-related product.
Year to begin affixing CE marking 2013.
Acer FT220HQL
FT220HQL
(“x” = 0~9, a ~ z, A ~ Z, or blank)
xxxxxx
ormity
Sep. 16, 2013
RU Jan / Sr. Manager Date Regulation, Acer Inc.
Federal Communications Commission
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The following local Manufacturer /Importer is responsible for this declaration:
Product: LCD Monitor
Model Number:
SKU Number:
Name of Resp
Address of Responsible Party: 333 West San Carlos St.
Contact Person: Acer Representative
Phone No.: 254-298-4000
Fax No.: 254-298-4147
FT220HQL
FT220HQL
onsible Party: Acer America Corporation
xxxxxx (“x” = 0~9, a ~ z, A ~ Z or Blank)
Suite 1500
San Jose, CA 95110 U. S. A.
Special notes on LCD monitors iii Information for your safety and comfort iii
Safety instructions iii
Cleaning your monitor iii Connecting/disconnecting the device iii Accessibility iv Safe listening iv Warnings iv Using electrical power iv
Product servicing v Additional safety information vi IT equipment recycling information vi Disposal instructions vii LCD pixel statement vii Tips and information for comfortable use viii Federal Communications Commission Declaration of Conformity
Unpacking 1
Screen position adjustment 2 Connecting the power cord 3 Power saving 3 Display Data Channel (DDC) 3 Connector pin assignment 4
Standard timing table 6 Installation 7
MHL (Mobile High-Definition Link) 8 User controls 9
How to adjust a setting 10
eColor Management 10 Adjusting the OSD 11
Troubleshooting
VGA mode HDMI mode 16
Getting started with Windows 8 on your new touch-enabled Monitor
xi
15 15
17
Unpacking
Please check that the following items are present when you unpack the box, and save the packing materials in case you need to ship or transport the
monitor in the future.
1
LCD monitor Quick start guide
D-sub cable (Optional)
USB cable (Optional)
HDMI cable (Optional)
Power Adapter
Audio Cable (Optional)
MHL cable (Optional)
AC power cord
2
Screen position adjustment
In order to optimize the best viewing position, you can adjust the monitor tilt of the monitor by using both of your hands to hold the edges of the monitor as shown in the figure below. The monitor can be adjusted to 10 degrees or 90 degrees up as indicated by arrow below.
0
10
90
0
Connecting the power cord
Check first to make sure that the power cord you use is the correct type
required for your area.
The monitor has a universal power supply that allows operation in either
100/120 V AC or 220/240 V AC voltage area. No user-adjustment is required.
Plug one end of the power cord to the AC inlet, and plug the other end
into an AC outlet.
For units using 120 V AC:
Use a UL-listed cord set, type SVT wire and plug rated 10 A/125 V.
For units using 220/240 V AC:
Use a cord set consisting of H05VV-F cord and plug rated 10 A/250 V. The cord set should have the appropriate safety approvals for the country in which the equipment will be installed.
Power saving
The monitor will be switched to "power saving" mode by the control signal from the display controller, as indicated by the amber-colored power LED.
Mode LED light
On Blue
Power saving Amber
3
The power saving mode will be kept until a control signal has been detected or the keyboard or mouse is activated. The recovery time from "power saving" mode back to "on" is around 3 seconds.
Display Data Channel (DDC)
To make installation easier, so long as your system supports the DDC protocol, the monitor is able to plug-and-play. The DDC is a communication protocol through which the monitor automatically informs the host system about its capabilities; for example, supported resolutions and corresponding timing. The monitor supports the DDC2B standard.
4
Connector pin assignment
5
10
15
1
6
11
15-pin color display signal cable
PIN No. Description PIN No. Description
1 Red 9 +5 V 2 Green 10 Logic ground 3 Blue 11 Monitor ground 4 Monitor ground 12 DDC-serial data 5 Self test 13 H-sync 6 R-ground 14 V-sync
-ground 15 DDC-serial clock
7 G 8B-ground
5
19-pin Color Display Signal Cable*
PIN No. Description PIN No. Description
1 TMDS Data2+ 2 TMDS Data2 Shield 3 TMDS Data2– 4 TMDS Data1+ 5 TMDS Data1 Shield 6 TMDS Data1– 7 TMDS Data0+ 8 TMDS Data0 Shield
9 TMDS Data0– 10 TMDS Clock+ 11 HDMI_DET 12 TMDS Clock– 13 14 Reserved (N.C. on device)
Reserved (N.C. on device) 15 SCL 16 SDA 17 DDC/CEC Ground 18 +5V Power 19 Hot Plug Detect
* only for certain models
13151719
12141618
1357911
810 462
*19-Pin Color Display
Signal Cable
PIN NO. DESCRIPTION
7. MHL+
9. MHL-
18. VBUS
19. CBUS
5, 11, 17 GND
*Only for MHL models
6
Standard Timing Table
Mode Resolution
1 2 3 4
5 6 7 8 9
10
11
12 13 14
*Only for MHL-Model
Mode Resolution
1 640x480 @60Hz
2 720x480 3 720x576 @50Hz 4 800x600 @60Hz 5 1024x768 @60Hz 6 1280x720 @60Hz 7 1280x720@50Hz 8 1920x1080i @60Hz 9
10 1920x1080 @30Hz
1112
13
14
VGA
MAC 640x480 66.66 Hz VESA 720x400 70 Hz SVGA 800x600 56 Hz SVGA 800x600 60
XGA 1024x768 60 Hz
XGA 1024x768 70 Hz VESA 1152x864 75 Hz
SXGA 1280x1024 60
VESA 1280x72 0 60 Hz
WXGA 1280x800 60
WXGA+ 1440x900 60
WSXGA+ 1680x1050
UXGA 1920x1080 60
640x480 60 Hz
60 Hz
@60Hz
1920x1080i @50Hz
1920x1080p @60Hz
1920x1080p @50Hz
720(1440)x480i @60Hz
720(1440)x576i @50Hz
Hz
Hz
Hz Hz
Hz
7
INSTALLATION
To install the monitor to your host system, please follow the steps as given below:
Steps
1.1-1
1-2/1-3
2.
3.Connect the Audio Cable(Only Audio-Input Model)(Optional)
4.Connect pow
5.Power-ON Monitor and Computer
6.If the monitor still does not function properly, please refer to the
Connect Video Cable a. Make sure both the monitor and computer are powered-OFF. b. Connect the VGA video cable to the computer.
Connect
HDMI or MHL Cable
a. Make sure both the monitor and computer are powered-OFF. b. Connect the HDMI cable to the computer or connect MHL
cable
to the portable device.
Connect the USB Cable(Optional)
er adapter and power cord
Connect the pow
er adapter and power cord
a properly grounded AC
outlet.
to the monitor, then to
Power-ON the monitor first, then power-ON the computer. This sequence is very important.
troubleshooting section to diagnose the problem.
VGA
HDMI HDMI
4
1-3
4
3
1-2
1-1
USB
2
1-21-1
1-3
VGA
USB
3
HDMI
HDMI
2
8
MHL (Mobile High-Definition Link) (Only for MHL-input Models)
Mobile High-Definition Link is a digital interface for transmitting video and audio from an external portable device. It is also capable of charging a portable device (5 V @ 900 mA).
Connecting the devices
Plug the MHL-certified cable into the display's HDMI® (MHL) port and the portable device's HDMI
®
-out port.
MHL
MHL
Using MHL
MHL-certified portable devices will automatically display content on the monitor, provided the output display and audio formats are supported by the portable device.
When the portable device is in standby mode, the monitor will show a black screen or turn to standby mode, depending on the portable device's output signal.
Due to the difference in size and resolution between the monitor and the portable device, you may find the display quality not as crisp as it appears on the portable device. This may be due to the portable device changing the output format.
This monitor only receives content from the portable device. It is not capable of controlling the portable device.
9
USER CONTROLS
Power Switch / Power LED:
To turn the monitor ON or OFF. Lights up to indicate the power is turned ON.
Using the Shortcut Menu
Press the function button to open the shortcut menu. The shortcut menu lets you quickly select the most commonly accessed settings.
Empowering:
Press the Empowering Key to open the eColor Management OSD and access the scenario modes.
AUTOAuto Adjust:
Press this button to activate the Auto Adjustment function. The Auto Adjustment function is used to set the HPos, VPos, Clock and Focus.
MENUOSD functions:
Press this botton to activate the OSD menu.
Volume Up/Down:
Press to adjust volume(only Audio-Input Mode)(Optional).
INPUTInput Key:
Use Input key to select from different video sources that may be connected to your monitor.
)
(
c
(a) VGA input (b) As you cycle through the sources you will see the following messages on right top side of screen to indicate currently selected input source. It may take 1 or 2 seconds for the image to appear. VGA or If either VGA or HDMI or MHL input is selected ,but the VGA and HDMI and MHL
lables are not
“No Cable Connect” or “No Signal”
HDMI or MHL
HDMI(MHL)
connected
, a floating dialog box indicates:
input
HDMI(MHL)
input
10
Acer eColor Management
Operation instructions
Step 1: Press “ “ Key to open the Acer eColor Management OSD and
access the scenario modes Step 2:Press “ “ or “ ” to select the mode Step 3:Press “ AUTO “ Key to confirm the mode and exit the eColor menu.
Features and Benefits
Main
Menu
icon
Sub
Menu
icon
N/AUser mode
N/A
N/A
N/A
N/A
Sub
Menu
item
mode
ECO
Standard
mode
Grahpic
mode
Movie
mode
Description
User defined. Settings can be fine-tuned to
suit any situation
Adjusts the consumption.
Default Setting. Reflects native display
capability
Enhances colors and emphasize fine detail. Pictures and photographs appear in vibrant
colors with sharp detail.
Displays scenes in clearest detail. Presents great visuals, even in unsuitably-lit
environments.
settings to reduce power
11
Adjusting the OSD settings
--------------------------------------------------------------------
Note: The following content is for general reference only. Actual product specifications may vary.
The OSD can be used for adjusting the settings of your LCD Monitor. Press the MENU key to open the OSD. You can use the OSD to adjust the picture quality, OSD position and general settings. For advanced settings, please refer to following page:
Adjusting the picture quality
1Press the MENU key to bring up the OSD.
2Using the / keys, select Picture from the OSD. Then navigate to
the picture element you wish to adjust. 3Use the / keys to adjust the sliding scales. 4The Picture menu can be used to adjust the current Brightness, Contrast,
Colour Temp, Auto Config and other image-related qualities.
12
Adjusting the OSD position
1Press the MENU key to bring up the OSD.
2Using the directional keys, select OSD from the on screen display.
Then navigate to the feature you wish to adjust.
Adjusting the setting
13
1Press the MENU key to bring up the OSD.
2Using the / keys, select Setting from the OSD. Then navigate to
the feature you wish to adjust. 3The Setting menu can be used to adjust the screen Menu Language and
other important settings.
14
Product information
1Press the MENU key to bring up the OSD.
2Using the / keys, select Information from the OSD. Then the
basic information of LCD monitor will show up for current input.
15
Troubleshooting
Before sending your LCD monitor for servicing, please check the troubleshooting list below to see if you can self-diagnose the problem.
VGA mode
Problem LED status Remedy
No picture visible Blue Using the OSD, adjust brightness and
contrast to maximum or reset to their default settings.
Off Check the power switch.
Check if the power cord is properly connected to the monitor.
Amber Check if the video signal cable is
properly connected at the back of monitor.
Check if the computer system is switched on and in power saving/ standby mode.
Unstable picture Check if the specification of graphics
Abnormal picture Image is missing,
off-center, too large or too small on the screen.
adapter and monitor is in compliance which may be causing the input signal frequency mismatch.
Using the OSD, adjust focus, clock, H­position and V-position with non­standard signals.
Check the display setting on your system. In case of a missing image, please select another resolution or vertical refresh rate.
English
Wait for a few seconds after adjusting the size of the image before changing or disconnecting the signal cable or switching off the monitor.
16
HDMI mode
English
Problem LED status Remedy
No picture visible Blue Using the OSD, adjust brightness and
contrast to maximum or reset to their default settings.
Off Check the power switch.
Check if the AC power cord is properly connected to the monitor.
Amber Check if the video signal cable is
properly connected at the back of monitor.
Check that the computer system is switched on and in power saving/ standby mode.
17
Getting started with Windows 8 on your new touch­enabled Monitor
We know this is a new operating system that will take some getting used to, so we've created a few pointers to help you get started.
* Note: For the touchscreen & USB function to work, you need to connect the USB cable to the NB or PC, as well as connecting through a VGA or HDMI cable.
Three concepts you might want to keep in mind
1. Start
The Start button is no longer available; you can launch apps from the Start screen.
2. Tiles
Live tiles are similar to thumbnails of the programs.
3. Charms bar
The Charms bar is a context-sensitive area containing settings and other useful functions.
How do I open the Charms bar?
Swipe the right-hand edge of the screen inwards to open the Charms bar.
How do I get to Start?
Press the Windows key, or swipe the right-hand edge of the screen to open the Charms bar and tap Start.
18
How do I jump between programs/apps?
Swipe the left-hand edge of the screen inwards to cycle through programs/apps that are currently running.
Alternatively you can drag the left-hand edge of the screen in slightly and release the thumbnail to open thumbnails of current programs/apps.
How do I turn off my computer?
Open the Charms bar, tap Settings > Power and select the action you'd like to take. Alternatively, from Desktop, tap Acer Power Button and select the action you'd like to take.
For more information please refer to your computer's User's Manual (open the Charms bar and search for 'User's Manual') or visit the following pages:
- Windows 8 tutorials: www.acer.com/windows8-tutorial
- Support FAQs: www.acer.com/support.acer.com
What is this thing called "Metro?"
"Metro" is a new interface for Windows 8 that is designed to work well with touch input. Programs writte screen and don't require closing in the traditional way. Metro apps will be displayed on Start using live-tiles.
What are "live tiles?"
Live tiles are similar to thumbnails of the programs that will be updated with new content whenever you're connected to the Internet. So, for example, you can view weather or stock updates without needing to open the app.
n for Metro will automatically use the whole
Loading...