ACE BAYOU DAC18, OCPBT20, DUAL21D User Manual

Torque

User Manual Item no: 5105801

Need Help? Email:

Phone: [phone]

IMPORTANT: You must keep your original retail receipt as proof of purchase.

Welcome to X Rocker!

Thank you for purchasing this X Rocker gaming

chair. You are now close to enhancing your
favourite games with glorious audio!

To get started, please assemble the chair using

the assembly instrucons on the separate leaet
and then follow the instrucons in this manual to

get rocking!

Table of contents

Box contents and control panel overview

3
4 Wireless connecon guide: PS4
5 Wireless connecon guide: Xbox One
6 Wireless connecon guide: TV (All systems)
7 Wired connecon guide: TV (All consoles)

Wired connecon guide: PS4 Controller only

8
9 Bluetooth connecon guide
10 Troubleshoong ps
11 Health and safety informaon
12 Power supply safety informaon

2

B

B1 - 3m 3.5mm to 3.5mm Audio cable

B2 - 15cm RCA to female 3.5mm audio cable

+

B1

+

B3

+ +

B5 B6

+

B7

+

+

B2

B4

0.8m

Control panel overview

B3 - RCA female to female adapters

B4 - Power supply Cable

B7 - Micro USB Cable

3

Step 1: Make sure that the PS4™ system is switched OFF. Insert the micro USB cable
into the X Rocker DAC converter and the other end into one of the front USB ports

Step 2: Turn the PS4™ system back on. Select one of the wireless bands
(1,2,3) on the wireless DAC and then switch to the corresponding band on
the chair.

Step 3:

Save, exit and enjoy!

4

Step 1: Make sure that the Xbox One™ system is switched OFF. Insert the
micro USB cable into the X Rocker DAC converter and the other end into
one of the back USB ports on the Xbox One™ system. Remove the clear

I

Step 2: Turn the Xbox One™ system back on. Select one of the wireless
bands (1,2,3) on the wireless DAC and then switch to the corresponding
band on the chair.

Step 3:

> [Display and Sound] > [Audio Output] > under [Digital Audio], select

Save, exit and enjoy!

5

Wireless connecon guide: TV
(All systems)

Transmier

TV/SPDIF/Opcal Socket

B6

B7

1. Connect B6 Opcal Cable to the B5 Wirelesss DAC transmier’s SPDIF Port.

2. Connect other end of B6 Opcal Cable to the TV Opcal socket.

3. Connect Micro USB Cable to the transmier and other end to an
available USB socket on the TV.

4. Once connected to your TV, increase volume to 50% of the maxiumum
for the best sound level.**

* N.B: If your TV does not feature an SPDIF or OPTICAL OUT Socket then you can
instead use the 3.5mm audio connecon to connect to a headphone socket.
** Depending on your TV you may need to enable the Opcal output seperately.

TV USB socket

6

Wired connecon guide: TV
(All consoles)

TV/Mobile/Tablet

B1

1. Connect B1 Cable to X Rocker control panel MP3 INPUT sockets.

2. Connect other end of B1 3.5mm end into the headphone socket of
your television.

3. Once connected to your TV, increase volume to 50% of the maximum
for the best sound level. **

** Depending on your TV you may need to increase the headphone
volume separately in the TV sound sengs.

7

Wired connecon guide: PS4
Controller only

B1

1. Connect the B1 cable to the boom of the PS4 controller via the
headset socket.

2. Connect the other end of the B1 cable to the chair via the green port.

3. With the PS4 turned on, go to the main menu (or locate the main
menu screen). Press and hold the PS buon on the PS4 controller unl
the quick menu appears on screen.

4. In this menu select [Adjust sound and devices]

5. Then select [output to headphones]

6. Change the seng from [Chat Only] to [All audio]

7. Make sure the volume in the previous menu is set to the maximum.

8. Set the control panel Wireless switch to the ‘OFF’ posion.

8

Step 1:

Step 2:

On the Audio output device

turn Bluetooth on if it is not
on already and search for

XROCKER

select the XROCKER
If a passcode is required the four
digit code will be ‘0000’.

9

Troubleshoong ps

Issue Troubleshoong steps

No power going to control panel

No sound

Wireless transmier cuts out during
gameplay/No vibraon or subwoofer
sound via analogue connecon

• Make sure that the power cable is
connected correctly.

• Make sure that the power supply at the
power source is working correctly.

• With the chair turned to the ON posion,
give the power cable a slight wiggle in the
port. If any lights icker (or not)
then please contact support (details below).

• Review the connecon methods on
the previous page and try alternave
connecon methods if possible.

• Conrm that the device/system is
correctly congured as per previous
connecon guide.

• Make sure that the wireless channel
switcher is in the corresponding posion
that suits your connecon method.
(1,2,3 for wireless and AUX for wired
connecons).

• Please make sure that the volume of

the source device is at a higher level to

strengthen the audio signal.

The cables connected to my
X Rocker have been broken
accidentally

Interference over wireless connecon

• Please contact X Rocker support
(service@XRockerNaon.co.uk) regarding
this issue.

• In this case, try another of the three

wireless bands to isolate the signal.

10

Health and safety informaon

• Avoid immersing or allowing the X Rocker to come into contact

with liquids.

• Please consult X Rocker Support before unscrewing any of the electrical

components on the chair.

• Please be mindful of any cabling laid out between the X Rocker and

power source/audio device.

• Please be mindful of cabling aached when moving/swivelling

the X Rocker.

• If the cables or electrical equipment are broken then this may present

a choking risk, please contact Support for replacements and dispose of

these parts safely.

• Do not stand on the X Rocker or exceed the 120kg weight limit via

other means.

• Do not lean back on the chair to the point in which the pedestal would

li o the ground.

• X Rocker armrests are designed for support and comfort during

gameplay, please do not use these as support for geng in/out of
the chair.

• Playing audio for long periods at loud volumes may contribute to

dicules in hearing.

• Please be considerate to others when playing audio through the

X Rocker speakers at higher volumes.

11

ATTENTION:
A. For Power Adapter, the apparatus shall not be exposed to dripping

or splashing and that no objects filled with liquids, such as vases,

shall be placed on the apparatus;
B. For Power Adapter, the MAINS plug is used as the disconnect device,

the disconnect device shall remain readily operable;
C.Only use the attachments/accessories specified by manufacturer.

Power Supply unit trademark: BI;
Model name: B18-090200-I;
Input: 100-240V~, 50/60 Hz, 0.8 A;
Output: 9 VDC, 2A;

12

Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
FCC NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

IC

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts. L'exploitation
est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas causer d'interférences, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.

IC Radiation Exposure Statement:

This equipment complies with Canada radiation exposure limits set forth for uncontrolled environments.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Déclaration d’IC sur l’exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux radiations définies par le Canada pour des environnements
non contrôlés.
Cet émetteur ne doit pas être installé au même endroit ni utilisé avec une autre antenne ou un autre émetteur.

Need Help? Email: [e-mail] Web: www.xrockernation.com Phone: [phone]

7

Need Help? Email: Service@XRockerNaon.co.uk

Phone: [phone]

www.XRockerNaon.co.uk

IMPORTANT: You must keep your original retail

receipt as proof of purchase.