AccuTemp S32401D060 Installation Manual
INSTALLATION & OWNERS MANUAL
S/N 35389 & HIGHER
IMPORTANT WARRANTY INFORMATION:
For product warranty activation, the Product Registration Form must be submitted
to AccuTemp Products, Inc. after installation of the appliance.
MP4002-1103
AccuTemp Products, Inc. · 8415 North Clinton Park · Fort Wayne, IN 46825 ·800 210-5907 · accutemp.net
TABLE OF CONTENTS
Table of Contents ............................................................................2
Document History ...........................................................................2
Safety Warnings ......................................................................3
Warranty ..........................................................................................4
Control & Component Identication ...............................................5-7
Installation .......................................................................................8-10
Initial Start-Up ...............................................................................10-11
Operation-Cooking ......................................................................11-12
Daily & Weekly Cleaning ................................................................13-14
Basic Troubleshooting .....................................................................15-16
Service Information .........................................................................17
DOCUMENT HISTORY
Current revision: MP4002-1103 Date:03/11
Prior revision: MP4002-0503 Date: 03/05
Changes
Operational changes due to new conguration changes.
MP4002-1103
STEAM’N’HOLD™
2 of 17
SAFETY WARNINGS
DANGER
Only personnel qualied to work with electricity should install this appliance. Improper
installation can cause personal injury or damage. This appliance must be properly grounded.
Failure to properly ground could result in electrocution and/or death.
WARNING
When using a stand that is equipped with the casters, the surface must be level. Failure to do so 1.
can result in a “tipping” situation and could result in serious injury.
Direct contact with steam can result in serious burns.2.
When accessing the cooking compartment, be sure to always stand back while slowly opening 3.
the door, allowing the compartment to vent the steam. Never look or reach into the cooking
compartment before the steam has completely vented.
Never reach into the cooking compartment or handle hot items without wearing proper protective 4.
equipment.
Never use wet or damp gloves, as moisture can conduct heat quickly and could result in severe 5.
burns.
CAUTION
Be sure all operators read, understand and follow the information contained in this manual, 1.
including caution warnings, operating instructions, and safety instructions.
Use caution when operating the steamer as direct contact with steam can result in severe 2.
burns.
Please use caution when emptying the appliance drain pan as the contents of the pan could 3.
cause severe burns.
Keep the oor in front of the appliance clean and dry.4.
Do not use pressurized water to clean the appliance.5.
Use of replacement parts other than those supplied by AccuTemp can cause injury to the operator, 6.
damage to the appliance and will void all warranties.
This appliance is extremely heavy and use of appropriate material handling equipment to install 7.
the appliance maybe required. Remove the packaging and move it into its nal location or
employ additional help as required for safe handling.
Do not use the low water warning indicator or buzzer as a substitute for checking the water 8.
level in the cooking compartment of the appliance periodically. Failure to properly maintain the
water level may result in improperly cooked product and over time may result in a premature
service problem that may void the warranty of the appliance.
Failure to complete the suggested operating, cleaning and preventive maintenance procedures 9.
may cause slow cooking or premature service problems that may void the warranty of the
appliance.
MP4002-1103
STEAM’N’HOLD™
3 of 17
WARRANTY
LIMITED WARRANTY
One Year - Parts & Labor - U.S. & Canada Only
AccuTemp Products, Inc. (AccuTemp) warrants that your AccuTemp equipment will be free of
defects in material and workmanship under normal use for a period of twelve (12) months from
installation or fteen (15) months from date of shipment from AccuTemp, whichever date rst
occurs (the Warranty Period). Registration of AccuTemp equipment is required at the time of
installation. Damage to AccuTemp equipment that occurs during shipment must be reported to the
carrier, and is not covered under this warranty. The reporting of any damage during shipment is the
sole responsibility of the commercial purchaser/user of such AccuTemp equipment.
AccuTemp provides an active service department, which should be contacted and advised of
service issues, regardless of the warranty period. During the warranty period, AccuTemp agrees
to repair or replace, at its option, F.O.B. factory, any part which proves to be defective due to
defects in material or workmanship, provided the equipment has not been altered in any way and
has been properly installed, maintained, and operated in accordance with the instructions in the
AccuTemp Owners Manual. During the warranty period, AccuTemp also agrees to pay for any
factory authorized equipment service agency (within the continental United States and Canada)
for reasonable labor required to repair or replace, at our option, F.O.B. factory, any part which
proves to be defective due to defects in materials or workmanship, provided the service agency has
received advance approval from AccuTemp factory service to perform the repair or replacement.
This warranty includes travel time not to exceed two hours and mileage not to exceed 50 miles
(100 miles round trip), but does not include post start-up assistance or training, tightening of loose
ttings or external electrical connections, minor adjustments, maintenance, gaskets or cleaning.
AccuTemp will not reimburse the expense of labor required to replace parts after the expiration of
the warranty period.
Proper installation is the responsibility of the dealer, owner-user, or installing contractor and is
not covered by this warranty. Improper installation can affect your warranty. Installation is the
responsibility of the Dealer, Owner/User or the Installation Contractor. See the Installation section
of the Owners Manual. While AccuTemp products are built to comply with applicable standards for
manufacturers, including Underwriters Laboratories (UL) and Underwriters Laboratories Sanitation
requirements, it is the responsibility of the owner and the installer to comply with any applicable local
codes that may exist.
AccuTemp makes no other warranties or guarantees, whether expressed or implied, including any
warranties of performance, merchantability, or tness for any particular purpose. AccuTemp liability
on any claim of any kind, including negligence, with respect to the goods and services covered
hereunder, shall in no case exceed the price of the goods and services, or parts thereof, which gives rise
to the claim. In no event shall AccuTemp be liable for special, incidental, or consequential damages,
or damages in the nature of penalties.
This constitutes the entire warranty, which supersedes and excludes all other warranties, whether
written, oral, or implied.
MP4002-1103
STEAM’N’HOLD™
4 of 17
TEMPERATURE GAUGE
VACUUM GAUGE
TIMER
STEAM’N’HOLD™-CONNECTIONLESS
OPERATIONAL INSTRUCTIONS
STATUS AND FAULT
ALARMS INDICTORS
SELECTOR SWITCH POWER, FAST COOK &
LOW TEMPERATURE
COOK
OFF PUSH BUTTON
ADJUSTABLE FOOT
DOOR LATCH
LOW TEMPERATURE STEAM
& HOLD THERMOSTAT
DRAIN VALVE
(CLOSED POSITION)
CUSTOMER SUPPLIED
DRAIN PAN
DRAIN PAN (NOT SUPPLIED)
MUST BE INSTALLED DURING
COOKING AND DRAINING
OPERATIONS.
CONTROLS AND HARDWARE LOCATIONS ARE THE SAME FOR THE S3 AND S6 MODELS
FIG. 1
MP4002-1103
STEAM’N’HOLD™
5 of 17
TEMPERATURE GAUGE
VACUUM GAUGE
TIMER
STEAM’N’HOLD™-CONNECTED
OPERATIONAL INSTRUCTIONS
STATUS AND FAULT
ALARM INDICATORS
SELECTOR SWITCH POWER, FAST COOK &
T-STAT COOK
OFF PUSH BUTTON
ADJUSTABLE FOOT
DOOR LATCH
LOW TEMPERATURE STEAM
& HOLD THERMOSTAT
DRAIN VALVE
(CLOSED POSITION)
CONDENSATE TRAY
CONTROLS AND HARDWARE LOCATIONS ARE THE SAME FOR THE S3 AND 6 PAN MODELS
FIG. 2
MP4002-1103
STEAM’N’HOLD™
6 of 17
Loading...