Accusplit Eagle 602M100D User Manual
z 602M100D (FY)
MULTI-FUNCTION STOPWATCH
STOPWATCH OPERATING INSTRUCTIONS
This watch has three modesand
3-STROKE/STRIDE MEASUREMENT.
the
[MODE]
button to cycle continuously through
TIME, STOPWATCH,
Press
these modes.
TIME MODE
To set current date and time ot day press
[RESET]
button. SECONDS indicator will tiash to indicate you
are in SET mode.
Press
[RESET]
to cycle through and set each tield
(SECONDS -> MINUTES -> HOURS -> YEAR ->
MONTH -> DAY). Eield being set will tiash. Press
[START]
button to set each tield.
STOPWATCH MODE
Event and Time-Out/Time-ln
Press
[START]
Press
[STOP]
-Start timing
-Stop timing (Time-Out, Display
shows “STOP”)
Press
[START]
Press
[STOP]
-Start timing (Time-In)
-Stop timing (Time-Out, Display
shows “STOP”)
Press
[RESET]
Dual Split Memory with Split Counter
Press
[START]
-Reset (Display Only)
-Start timing (Shows Running
CUM Time)
Press
[LAP/SPLIT]
-create 1st Split or Lap time
(Top row shows SPLIT 1, middle shows LAP 1,
and bottom row shows running cumulative time)
Press
[LAP/SPLIT]
-create 2nd Split (Top row shows
SPLIT 2, middle shows LAP 2)
Press
[LAP/SPLIT]
-create 3rd Split (Top row shows
SPLITS, middle shows LAP 3)
Press
[LAP/SPLIT]
-create 4th Split (Top shows
SPLIT 4, middle shows LAP 4)
Press
[STOP]
-Stop timing (Bottom shows Cumulative
elapsed time)
Press
[RESET]
Notes:
Bottom row always shows Running Cumulative (CUM)
time. Split Counter shows the current Split being taken.
Last Split must be taken at end. Stop does not Split.
Memory Recall
While stopwatch is running:
Press
[RECALL]
last Lap/Split times.
Press
[RECALL]
each time
While stopwatch is stopped:
Press
[RECALL]
tirst Lap/Split times.
Press
[RECALL]
each time
-Reset display only (memories remain)
-Recalls CUM time at last stop, or
-Recalls previous Lap/Split/Stop time
[RECALL]
is pressed.
-Recalls CUM time at tirststop, or
-Recalls next Lap/Split/Stop time
[RECALL]
is pressed.
Notes:
Hold down
Whenever the storage is tull, “LULL” icon will be lit,
and extra Split times will not be stored into memory
(but will still be shown on the display). You can clear
the memories by stopping and resetting the watch.
3-STROKE/STRIDE MEASUREMENT MODE
In this mode you can tind Counts per Minute
(treguency) ot a swimmer’s strokes, a runner’s
strides, etc. Press
Atter you have observed THRLL strokes or strides,
press
Minute (rate).
otthe range ot 10-180, “Lrr” will appear to show the
error condition. Press
reading to “0_0’i
NO-PROOF-OF-PURCHASE LIMITED WARRANTY
See label on back of unit for details, or check
http://support.ACCUSPLIT.com
[RECALL]
[STOP]
NOTE:
RECA LL B ut ton
START
and
STOP
Butto n
-YEA R
■MONT H
and DAT E
■TIM E
(24H)
Watch is
in TIME
OE DA Y
MODE
MODE
Butto n
- Cur ren t
SPLIT
Time
■ Cu rre nt
LAP
Time
■CUM
Time
tor rapid review.
[START]
to start the measurement.
to stop and display the Counts per
It the stroke treguency tails out
[RESET]
to reset the displayed
ACCUSPLIT, Inc.
6120 Stoneridge Mall Rd.
Suite 210
Pleasanton, CA 94588 USA
800-965-2008 • 925-226-0888
FAX 925-463-0147
www.ACCUSPLIT.com
support@ACCUSPLIT.com
Loading...