Accusplit AX602M500, AX602M500DEC User Manual

b-1

ACCUSPLIT, Inc.

6120 Stoneridge Mall Rd., Suite 210

Pleasanton, CA 94588 USA

800-965-2008 • 925-226-0888 • FAX [phone]

www.ACCUSPLIT.com • [e-mail]

980-314

ACCUSPLIT®

E X CLUSIVE

AX602M500

AX602M500DEC

DIGITAL QUARTZ

STOPWATCHES

OPERATING

INSTRUCTIONS

2-3

IMPORTANT NOTE

This stopwatch can store up to 500 split/lap times.
However please note when there are 5 free mem­ories left, the icon “FULL” will blink to remind you
of the nearly full situation. Whenever the storage
is full, extra split/lap times will NOT be stored into
memory even though you reset your stopwatch
and start a new event. Extra split/lap times will
only be shown on the display but not recorded.

In order for the stopwatch to record the lap/split
times again, you must delete the data in the DATA
memory. Please refer to the “Data Mode” section
in the instruction manual for how to delete the
memory.

2 3

Introduction

You are about to enjoy an advanced Cumula­tive and Lap memory professional digital quartz
stopwatch with advanced timing features. Models
AX602M500 & AX602M500DEC Stopwatches
include Time of day, Daily Alarm, Chronograph
stopwatch, 500 memory, Data register, Count­down timer, Stroke Measurement timer, and Pacer
(from 5 to 240 beats per minute).

Model AX602M500DEC Decimal Stopwatch
includes Decimal timing (1/100 of a sec,
1/1000 of a minute, 1/100,000 of an hour).

Model AX602M500 Speed Stopwatch includes
Speed Measurement.

INSTRUCTIONS

4-5

General Features

• ACCUSPLIT X case with ergonomic design and
no-fail buttons

• 4 button operation

• Large LCD display with contrast adjustment

• 12/24 hour display

• Time of day and chime

• Daily alarm

• Full 1/100 second chronograph with working
range from 0 to 19 hr. 59 min. 59.99 seconds
with 500 memory records of split and lap time.

• Recall function for recorded split and lap times

• Count-Down timer with working range from 0 to
19 hr. 59 min. 59.9 seconds

4 5

• Three operating modes (Countdown Repeat,
Countdown Stop, Countdown then count up)
for countdown timer

• Stroke/Stride measurement basing on “3”

• Speed measurement (AX602M500 Model only)

• Decimal second, minute and hour chronograph
(AX602M500DEC Model only)

• Beep sound selectable

• Uses long life Lithium CR2032 battery for years
of use between battery changes

• Low battery check

The operation of the stopwatch is divided into
nine modes. As you choose each “mode”, a
message will be displayed for a second before
you enter the mode:

6-7

Press MODE to cycle through:

Normal Time mode

TIME

Alarm mode

ALARM

Chronograph mode

CHRONO

SPLIT
or

STOP

LapTime Recall mode

6 7

RECALL

RECALL

Speed mode

(AX602M500 only)

SPEED

Stroke Measurement

STROKE

Pacer mode

PACER

Timer mode

TIMER

Data mode

DATA

Button Operation

• MODE - used to

change the watch’s
operating mode

• START • SPLIT - used
to start the timer or
stopwatch, and for taking
split and lap times

• RECALL - used to recall recorded split
and lap times (memories)

• STOP • RESET - used to stop and reset the
stopwatch or timer

8-9

This is only a brief description of these buttons.
Detailed uses of the buttons are different in
particular functions and will be described later in
the instructions.

Pressing [MODE] button will toggle among the
modes above. Note that there is no auto-return
function in the stopwatch. Whenever you change
modes, the stopwatch will remain in that mode
until the [MODE] button is pressed again.

8 9

Time of Day Mode

The starting point for operating your stopwatch
is TIME OF DAY. If TIME OF DAY is not displayed,
press [Mode] until it is.
Year : - 2008
Date : - January 1
Day of week : - Monday
Time : - 12:00 am

The display format is as below :

° year

° day, month - date

° hr : min second

10-11

ACCUSPLIT products use a common setting procedure known
as S1-S2-S3-S4.

S1 (2 sec) - Enter set function OR
S1 (4 sec) - Enter set function & clear the current settings
S2 – Select fi eld to be set (selected fi eld will fl ash)
S3 – Set fi eld to desired settings
S4 – Exit setting function

S1/S4

S2

Hour

S3

Year

Month and date

Seconds

Minutes

MODE

During clock display, press [START • SPLIT] to
switch between 12 hr and 24 hr display mode.
To toggle chime ON or OFF, you can press [STOP

• RESET]. The bell icon will be ON or OFF corre­spondingly.

Normal Time Setting

Press and hold [RECALL] (S1) for 2 seconds to
enter setting mode. The normal time setting starts
with second. The second digits will be fl ashing.
You can change the fl ashing digit by pressing
[START • SPLIT] (S3) button. To speed up the
setting you can press and hold [START • SPLIT]
for longer than 2 seconds to activate fast set­ting. To select other digits, press [STOP • RESET]
(S2) button. The setting order is: Second, Minute,
Hour, Year, Month, Date, month-date (m-d) or

1110

12-13

date-month (d-m), Sound ON or OFF, Contrast
(darkness of the digits - default is 9), then back to
Second, and recycles again.

Note: when the second is to be set, press [START

• SPLIT] to reset the second digits to zero. At the
end of setting, press [RECALL] (S4) or [MODE] to
exit from the setting mode and back to Time of
Day Display.

Display for Sound ON or
OFF setting :
(Let the current status be “ON”.)

Press [START • SPLIT] to toggle
Sound ON or OFF.

Display for contrast adjustment:
(Let the current contrast be “5”)

12 13

S O U n d
O n

S O U n d
O n

C O n T
5

Press [START • SPLIT] conse­cutively to advance the contrast
up to 16, then cycle back to 1.
The contrast setting will be
shown on the display.

NOTE:

• The hour digits may be displayed in 12 hr or
24 hr format.

• The year digits can be set from 2000 to 2099.
The date adjusts automatically for odd and even
months including February of leap years. The
day of week also adjusts automatically after you
set the date.

C O n T
1 6

14-15

Alarm Time Mode

Press [MODE] until you enter Alarm mode. This
mode is used for displaying the daily alarm time
and allows you to enable or disable the alarm.

When you enter the Alarm Time mode, the display
shows the alarm time on the upper line while the
date is shown in the middle of the display and the
normal time is on the lower line.

° Alarm Time

Alarm

Indicator

° day, month - date

° hr : min second

14 15

To toggle the alarm ON or OFF, press [STOP • RESET].
When alarm is ON, the indicator “
while it will be turned off when alarm is disabled.
When alarm time is reached, the alarm signal will
sound for 60 seconds. Press any button to stop the
alarm sound.

Setting Alarm Time

Press and hold [RECALL] (S1) for 2 seconds to ac­tivate the alarm setting. The alarm “minute” digits
will fl ash as an indication. Adjust the fl ashing digit
by pressing [START • SPLIT] (S3). To set the alarm
hour digits, press [STOP • RESET] (S2) to switch to
hour digits and then press [START • SPLIT] (S3) to
adjust. Press [RECALL] (S4) or [MODE] to exit from
Alarm setting mode.

” will be ON

16-17

Chronograph and Recall Mode

Press [MODE] until you enter the Chrono mode.

The stopwatch can measure up to 19 hours,
59 minutes, 59.99 seconds. When you enter the
Chronograph mode, the display format is as
below.

16 17

The upper line shows the split time, the middle
line shows the lap time and the accumulated
elapsed time is displayed on the lower line.

Whenever the stopwatch stops running, the
“STOP” indicator will be ON. Press the button
[START • SPLIT] to start the stopwatch. As it runs,
the current elapsed time is shown on the lower line.

° Split time

Split

counter

° Lap time

° Cumulative time

18-19

To take a current split or lap time, press [START •
SPLIT]. The display will look like this:

The stopwatch can store up to 500 split/lap times.
The split/lap times are stored into the memory as

The number of split/lap times taken are shown in
the upper left corner. The corresponding split and
lap times are displayed on the upper and middle
line. Press [START • SPLIT] again, the next split/lap
time will be shown and the number of split/lap
time is updated.

18 19

you press [START • SPLIT] to take each split/lap
time. Meanwhile, the lap and split time will be
frozen for 5 seconds. After this 5-second period,
the lap and split time will return to normal.

In addition, the fastest lap, the slowest lap, and the
averages of all laps will also be recorded. As you
press [STOP • RESET] to stop the chronograph, the
last lap/split time will also be stored (provided that
the last lap/split time is not the fi rst lap/split time).