Accusplit A925MXTBL User Manual

ACCUSPLIT A925MXTBL

0:32:29

.

38

0:05:03

.

1 1

A

C

C

U

S

P

L

I

T

∞

S

1

/

S

4

S

2

A

O

S

L

EL

S

3

M

4

SPLIT

0:32:29

.

38

0:05:03

.

1 1

A

C

C

U

S

P

L

I

T

∞

S

1

/

S

4

S

2

A
O

S

L

EL

S

3

M

925MX
TURBO

4

SPLIT

Wrist-Worn Stopwatch with Split Memory

Operating Instructions

Congratulations on your purchase of an A925MXTBL stopwatch

for the wrist! You’re about to enjoy the convenience of having

professional timing right at your ngertips when you need it,

plus a regular wristwatch whenever you don’t.

S1/S4

L

S2

SETUP

Most watches ship with a battery inter­rupt in place to save battery life. Turn the
watch over and use a quarter or nickle
to twist open the battery compartment
hatch. Remove clear plastic strip from
underneath the battery. Replace the bat­tery, taking care to ensure that the posi­tive (+) terminal is facing up. Replace the
battery compartment hatch and tighten
with the coin, making sure that the small
arrow points to the dot at the top of the
watch case when you are finished. Peel
the simulated display sticker off the
watch face.

Your new watch has four modes of op­eration: 1/100th second Memory Stop-

watch with Turbo features, Triple-mode
Timer, plus two Time-of-Day/Date/Alarm

modes. When the battery is enabled,
your watch will come to life in stopwatch
mode. Press the Lbutton to cycle be­tween the modes. Your watch also has an
Electroluminescent backlight. Press the
EL button to activate the backlight.

STOPWATCH MODE

The watch features a professional timing
circuit with powerful stopwatch features.
This is how the display looks when in
stopwatch mode.

Split Counter

Split Time Lap Time

Master Reset

Its a good idea to reset the stopwatch
each time before use. Push S2 for
2 seconds to Reset**

Event Timing

Event timing is the simplest form of tim­ing. It is good when you want to mea­sure the total time from the start to the
finish of a particular event.

S2 – Start
S2 – Stop (Display shows “SPLIT”)
S2 (2sec) – Reset**

800-965-2008 • 925-226-0888 • FAX [phone] • www.ACCUSPLIT.com • [e-mail]

ACCUSPLIT, Inc. • 6120 Stoneridge Mall Rd., Suite 210 • Pleasanton, CA 94588 USA

Dual Split Memory with Split
Counter

When timing an activity with pauses
or repeated events, you will need to
use split timing with memories.

S2 – Start (Shows Running DUAL Time)
S2 – Split* (Top shows CUM 1, Bottom

shows LAP 1)
S2 – Split* (shows CUM 2, Bottom shows
LAP 2)
S2 – Split* (Top shows CUM 3, Bottom
shows LAP 3)
S2 – Split* (Top shows CUM 4, Bottom
shows LAP 4)
S2 (2sec) – Reset**

*Split Counter always shows Current Split

Note: You can always press S1/S4 to return
to Running Time.

Memory Review (before Resetting)
M – Review* (Bottom shows AVE LAP

Split, Top shows TOTAL ELAPSED TIME)

M – Review (Shows last DUAL Split)
M – Review (Shows next DUAL Split, in

reverse order)

*Reviews at any time in reverse numerical
order. Hold down for Rapid Review.

STOPWATCH AND SPEED/RATE

The advanced “Turbo” functions on
the watch calculate speed or rate once
distance has been input into the watch
(recall that Rate = Units/Time).

Turbo
Set up
Display

Speed/Rate Function Setting
S1(2sec) - Enter Turbo (Speed/Rate) Set

Function
S1(4sec) – Enter set function and Reset
Turbo fields to zero (as for DUAL
SPLIT timing)
S2 – Select field to be Set (field will
flash)

S3 – Set field to Desired Setting
S4 – Exit Setting Function

EL Backlight
Button

When a Distance or Sample Count Is set
In Turbo Set Up mode, “SPD” (Speed)
indicator will be illuminated at bottom of
display. The number you enter should
correspond to the Distance or Sample
Count you want to use for the Speed
or Rate Computation. “P-HR” in display
means watch is set to compute “per
Hour” rate, and “P-Mn” means watch is
set to compute a “per Minute” rate.

If you want the watch to compute in “per
Sec” rate, divide the Distance or Sample
Count (Strokes, Strides, Units, etc.) by
60, then enter it.

For example, let’s say that you are at a
race track with a course that is one mile
long. If you set the Distance to 1.00 and
the rate to “P-HR,” and then time several
laps, the Average Speed recorded by the
watch will be in miles per hour.

Speed/Rate Function Operation
S2 – Start (Shows Running LAP Time)
S2 – Split* (Top and Bottom show

SPEED/RATE 1/LAP 1)
S2 – Split* (Top and Bottom show
SPEED/RATE 2/LAP 2)
S2 – Split* (Top and Bottom show
SPEED/RATE 3/LAP 3)
S2 (2sec) – Reset LAP and SPEED/RATE
to zero**

*For only chance to view Total Average
Speed/Rate, push M.

Memory Review (before Resetting)
M – Review* (Bottom shows AVE

TOTAL SPEED/RATE, Top shows TOTAL
ELAPSED TIME)
M – Review* (Bottom shows AVE LAP
Split, Top shows TOTAL ELAPSED TIME)
M – Review (Shows last SPEED/RATE
and LAP Split)
M – Review (Shows next SPEED/RATE
and LAP Split, in reverse order)

*Reviews at any time in reverse numerical
order. Hold down for Rapid Review.

**Reset before 30 hrs. (end of range) and
rollover.

S3 & M

TRIPLE MODE TIMER

The Timer can Count Down to Alarm,
Count Up to Alarm, or Count Down to
Alarm, and then Up. When you see a

small arrow or arrows in the lower left
hand corner of display, you are in Timer
mode. This is how the display looks in
Timer Mode.

Number of
Cycles to
Repeat

Countdown
Interval

Watch is in
Countdown
Timer Mode

Number of

Cycles

Completed

so far

Remaining

Time for this

Interval

Timer Set Instructions
S1 (2 sec) - Enter set function OR
S1 (4sec) - Enter set function & clear the

current settings
S2 select select field to be set (selected
field will flash)

S3 Set set field to desired settings
S4 exit exit setting function

Upon entering set function, you can
choose Count Down (#), Count Up ($),
or Count Down, then Up function ($#).
The next fields to be set are: Number of
Cycles to Repeat (not in Count Down­Up), Hours, Tens of minutes, Minutes,
Tens of Seconds, Seconds, then repeat.

Note: Count Up Timer can be used as an
Event Stopwatch. Since 0:00:00 is inter­preted as 30:00:00, Count Up Timer with
no time interval set will count up to 20
hours, as a time-out stopwatch.

Count Down or Count Up Timer
Operating Instructions
S2 - Start.

Top line of display shows number of
timing cycles to perform & number
of timing cycles preformed.
Middle line shows Time Interval for
each cycle.
Bottom line of display shows Time
Remaining (count down) or Elapsed
Time ( count up).

S2 - Stop. Display also shows “STOP”
S2 (2sec) - Reset to beginning

At end of every time interval, alarm
sounds for 5 seconds & timing cycle
repeats until stopped or cycle count
matches pre-programmed number of
cycles.

TIME OF DAY MODE

The watch keeps track of two complete
sets of time/day/date/alarm info (T1 and
T2). “T2” shows when the watch is in
Time-of-Day mode #2. This is how the
display looks in Time-of-Day Mode:

Month, Date,
and Day

Indicates
Watch in Time­of-Day Mode 2

Time

Setting the Time of Day, Day-Date,
and Alarms

Press ( repeatedly until you are in T1 or
T2, as desired.

S1 (2 sec) - Enter Set function
S2 - select select field to be set (field

will flash)

S3 - Set field to desired settings

Using Time of Day, Day, Date &
Alarm Functions
S3 - Alternates between Alarm & Day-

Date Display
Any button - Stops alarm sound

While in Alarm Display:

S2 - Changes Alarm & chime arm status:
Each press rotates through Alarm only
(display shows
(display shows

), Hourly chime

1

), or Both, then

+

neither.

Power Reset:

• Push and hold S2 and S3 - Display
turns OFF

• Release all - Display shows all
segments ON then displays stopwatch
at 0:00:00.00

Changing the Battery

When Low-Battery Indicator is “ON,”
replace the unit’s battery with a new Type
CR2016 Lithium cell, or equivalent.

PERFORMANCE SPECIFICATIONS
Stopwatch Performance Function
& Features

• 16 Dual Distance Split Automatic
Memory

• Hour, Minute, Second to 1/100 Sec

• 30 Hour Range

• Computers & Recalls Ave Lap Split

• Anytime Memory Review

• Rapid Memory Review

• FIFS (First In First Saved) Memory

• LIFO (last in First out) Memory

• Display True Split Count

• 1-Button Rapid Split & Reset Action

• Dual Split Timing

• Split Counter to 999 with Rollover

• Return to Running Dual Split

Timer Performance Function & Features

• Triple Mode Timer: Count Down to alarm,

• Count up to alarm, or Count down to
alarm, then count up.

• Start- stop 1/10 second stopwatch

• Auto Repeat of Count Down or Count Up
timer to pre-Programmed Cycle Count

• Displays preprogrammed Count Down,
up cycle count

• Display cycle completed

• 30 Hour Range (0:00:00=30:00:00)

• Hours, Minutes, Seconds Setting

• Hours, Minutes, Seconds, 1/10 Sec
Timing Display

Time of Day and Time of Day Alarm Func­tions and Features

• Time Day-Month, Day, Alarm

• 2nd Time, Date-Month, Day, Alarm

• Hourly Chime

General Performance Features

• 5 year NO-PROOF OF PURCHASE

Warranty

• NO-FAIL, Million – Cycle Switches

• Bold, Easy-to-Read Digits

• 60 degree Comfort Viewing Angle

• Water Resistant

• Shock Resistant

• 32,768Hz Quarts Crystal accuracy
to +or- 0.01 sec/hr

• 1.5 Year Battery Life

• Low-Battery Indicator

• Accurate Temp: 5C-35C (41F-95F)

• Operating Temp: -10C0-60C (14F-140F)

REGISTER NOW.

Please return your A925MXTBL
registration to the Repair Center
address in the warranty, and
we will let you know about

future products.

980-300A

Email __________________________

User ___________________________

_______________________________

_______________________________

NO-PROOF-OF-PURCHASE LIMITED WARRANTY

See label on back of unit for details, or check

http://support.ACCUSPLIT.com

Assembled in China. © ACCUSPLIT 2007