Accusplit 790M, 760M, 790MDEC User Manual
®
DIGITAL QUARTZ STOPWATCH
AE602M100 AE760M100
AE790M500 AE790M500DEC
INSTRUCTION MANUAL
IMPORTANT NOTE FOR MODEL 760M & 790M
This stopwatch can store up to 100 or 500 split/lap times depending on the model. However please note when
there are 5 free memories left, the icon “FULL” will blink to remind you of the nearly full situation. Whenever
the storage is full, extra split/lap times will NOT be stored into memory even though you reset your stopwatch
and start a new event. Extra split/lap times will only be shown on the display but not recorded.
In order for the stopwatch to record the lap/split times again, you must delete the data in the DATA memory.
Please refer to the “Data Mode” section on the instruction manual for how to delete the memory.
Instructions
Introduction
You are about to enjoy an advanced Cumulative and Lap memory professional digital quartz stopwatch with
advanced timing features.
Model AE602M100, AE760M100, AE790M500 & AE790M500DEC Stopwatch includes Time of day, Daily
Alarm, Chronograph stopwatch, 100 or 500 memory, Data register (Model 760M & 790M only), Countdown
timer, Stroke Measurement timer, Pacer from 5 to 240 beats per minute.
Model AE790M500DEC Decimal Stopwatch includes Decimal stopwatch (1/100 of a sec, 1/1000 of a
minute, 1/100,000 of an hour).
Model AE760M100 & AE790M500 Speed Stopwatch includes Speed Measurement.
General Features
- 4 buttons operation
- Large LCD display with contrast adjustment
- 12/24 hour display
- Normal time and chime
- Daily alarm
- Full 1/100 second chronograph with working range from 0 to 19 hr. 59 min. 59.99 seconds with 100 or
500 memory records of split and lap time.
- Recall function for recorded split and lap times
- Count-Down timer with working range from 0 to 19hr. 59min. 59.9 seconds
- Three operating modes (Countdown Repeat, Countdown Stop, Countdown then count up) for countdown timer
- Stroke measurement basing on "3"
- Speed measurement (AE760M100 & AE790M500 Model only)
- Decimal second, minute and hour chronograph (AE790M500DEC Model only)
- Segmented run memory (Model 760M & 790M only)
- Beep sound selectable
- Low battery check
1
As you choose each "mode", a message will be displayed for a second before you enter the mode:
Normal Time mode
(All models)
Alarm Time mode
(All models)
Chronograph mode
(All models)
Lap Time Recall mode
(All models)
Data mode
(760M & 790M models only)
The operation of the stopwatch is divided into eight modes (as noted above):
1. Normal time mode
2. Alarm time mode
3. Chronograph and Recall mode
4. Data mode (760M & 790M Models only)
5. Count-down timer mode
6. Pacer mode
7. Stroke measurement mode
8. Speed mode (AE760M100 & AE790M500 model only)
Button Operation
- Mode - used to change the mode of the watch
Start / Stop / Set - used to start and stop the timer counting or the chronograph function
- Recall - used for recalling recorded split and lap times
2
- Lap / Split / Reset / Select - for taking the record of the split and lap time
TIME
ALARM
CHRONO
RECALL
DATA
Timer mode
(All models)
Pacer mode
(All models)
Stroke Measurement
(All models)
Speed mode
(AE760M100 &
AE790M500 model only)
TIMER
PACER
STROKE
SPEEd
This is only a brief description of these buttons. Detailed uses of the buttons are different in particular functions
and will be described later in the instructions.
Pressing [MODE] button will toggle among the modes above. Note that there is no auto-return function in the
stopwatch. Whenever you change modes, the stopwatch will remain in that mode until the [MODE] button is
pressed again
Each time you enter a mode, a message will be displayed for a second before you enter the mode:
Note:- In the following descriptions, items printed in dark gray stand for flashing digits.
Normal Time Mode
The starting point for operating your stopwatch is NORMAL TIME. If NORMAL TIME is not displayed, press
[Mode] until it is.
Year : - 2001
Date : - January 1
Day of week : - Monday
Time : - 12:00 am
The display format is as below :-
2 0 0 1
W E 1 - 3
A 1 0 : 3 5' 3 0
During clock display, press [START] to switch between 12Hr and 24Hr display mode. To toggle chime ON or
OFF, you can press [RESET]. The bell icon will be ON and OFF correspondingly.
➔
year
➔
day, month - date
➔
hr : min second
Normal Time Setting
Press and hold [RECALL] for 2 seconds to enter setting mode. The normal time setting starts with second. The
second digits will then be flashing. You can change the flashing digit by pressing [START] button. To speed up
the setting you can press and hold [START] for longer than 2 seconds to activate fast setting. To select other
digits, press [RESET] button. The setting order is: Second, Minute, Hour, Year, Month, Date, month-date (m-d)
3
or date-month (d-m), Sound ON or OFF, Contrast (darkness of the digits - default is 9), then back to Second,
and recycles again. Note: when the second is to be set, press [START] to reset the second digits to zero.
At the end of setting, press [RECALL] or [MODE] to exit from the setting mode and back to Normal Time
Display.
Display for Sound ON or OFF setting :(Let the current status be "ON".)
SOUnd
On
Press [START] to toggle Sound ON or OFF.
SOUnd
On
Display for contrast adjustment:(Let the current contrast be "5")
COnT
5
Press [START] consecutively to advance
the contrast up to 16, then cycle back to 1.
The contrast setting will be shown on
the display.
NOTE:
- The hour digits may be displayed in 12hr or 24hr format.
- The year digits can be set from 2000 to 2099. The date adjusts automatically for odd and even months
including February of leap years. The day of week also adjusts automatically after you set the date.
4
COnT
16
Alarm Time Mode
Press [MODE] until you enter Alarm mode. This mode is used for displaying the daily alarm time and allows
you to enable or disable the alarm.
When you enter the Alarm Time mode, the display shows the alarm time on the upper line while the date is
shown in the middle of the display and the normal time is on the lower line.
AL P 3 : 3 0
TU 1 - 3
A 1 0 : 3 5' 3 0
To toggle the alarm ON or OFF, press [RESET]. When alarm is ON, the indicator "(((o)))" will be ON while it
will be turned off when alarm is disabled. When alarm time is reached, the alarm signal will sound for 60
seconds. Press any button to stop the alarm sound.
Setting Alarm Time
Press and hold [RECALL] for 2 seconds to activate the alarm setting. The alarm "minute" digits will flash as an
indication. Adjust the flashing digit by pressing [START]. To set the alarm hour digits, press [RESET] to switch
to hour digits and then press [START] to adjust. Press [RECALL] or [MODE] to exit from Alarm setting mode.
Chronograph and Recall Mode
Press [MODE] until you enter the Chrono mode.
The stopwatch can measure up to 19 hours. 59 minutes, 59.99 seconds. When you enter the Chronograph
mode, the display format is as below.
{000}
0: 00' 00" 00
SPLIT
0: 00' 00" 00
LAP
STOP
0: 00' 00" 00
The upper line shows the split time, the middle line shows the lap time and the accumulated elapsed time is
displayed on the lower line.
5
Loading...