Page 1
AcuRev 1310-ENC
NEMA4X rated Wall mount enclosure for AcuRev 1310 series
Installation Guide
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR
ARC FLASH.
• FOLLOW SAFE ELECTRICAL WORK PRACTICES.
SEE NFPA 70ET IN THE U.S., OR APPLICABLE LOCAL
CODES
• THIS EQUIPMENT MUST ONLY BE INSTALLED AND
SERVICED BY QUALIFIED ELECTRICAL PERSONNEL
• READ, UNDERSTAND, AND FOLLOW THE
INSTRUCTIONS BEFORE INSTALLING THIS PRODUCT
• TURN OFF ALL POWER SUPPLYING EQUIPMENT
BEFORE WORKING ON OR INSIDE THE EQUIPMENT
• USE A PROPERLY RATED VOLTAGE SENSING DEVICE
TO CONFIRM POWER IS OFF. DO NOT DEPEND ON
THIS PRODUCT FOR VOLTAGE INDICATION
FAILURE TO FOLLOW THESE INSTRUCTIONS WILL
RESULT IN DEATH OR SERIOUS INJURY.
A qualified person is one who has skills and
knowledge related to the construction and
operation of this electrical equipment and the
installation, and has received safety training
to recognize and avoid the hazards involved NECT 2011 Article 100.
NOTICE
AcuRev 1310 meter installed; AcuRev 1310 meter
and AcuRev 1310-ENC are ordered separately.
MAKE ENERGY USAGE SMARTER
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
• THIS PRODUCT IS NOT INTENDED FOR LIFE OR
SAFETY APPLICATIONS
• DO NOT INSTALL THIS PRODUCT IN HAZARDOUS OR
CLASSIFIED LOCATIONS
• THE INSTALLER IS RESPONSIBLE FOR
CONFORMANCE TO ALL APPLICABLE CODES
• MOUNT THIS PRODUCT INSIDE A SUITABLE FIRE
AND ELECTRICAL ENCLOSURE
. .
1
Page 2
The AcuRev1310 enclosure offers a mounting
option for AcuRev1310 Series energy meters that
helps protect from tampering and the elements.
The enclosure is equipped with DIN rail mounting
hardware for easy installation, and a NEMA®4X rating
ensures durability. The swing panel kit and multiple
locking options provide additional security from
unwanted tampering.
DIMENSIONS
1. Enclosure
2. DIN rail
3. Hinged lid
4. Clasp
5. Brackets for swing panel cover
6. Swing panel cover
7. Mounting feet
(hardware not pictured)
7,55 191,8
7,32 186
7,16 181,9
10-32 inserts
7,04 178,9
4,00 101,6
4,88 124
Find Quality Products Online at: sales@GlobalTestSupply.com
6,06 153,9
4,88 124
6,10 155
Top View - cover removed
10-32 Inserts
Wall fastening lug
1,65 42
4,72 120
,24 6
8,24 209,3
4,07 103,5
Hinged with latch
www.GlobalTestSupply.com
7,65 194,2
Hinged screw cover
7,39 187,6
Screw cover
. .
2
Page 3
Step 1. Mount the AcuRev1310 enclosure to a wall or a panel
Cut holes in the enclosure for wire conduit connections prior to the installation of the meter in the
enclosure. After running the wiring, seal all holes properly to maintain the enclosure rating. If using
metallic conduit, bonding between the conduit connections is not automatic and must be provided as a
part of the installation.
Take care to protect the equipment from drill chips,
filings, and other contaminants when making
the wire entry holes and mounting the enclosure
to prevent component damage or a future
malfunction.
Use the included mounting hardware to attach
the mounting feet to the enclosure. Then mount
the enclosure to the wall or the panel using either
a 4-point or 2-point configuration (hardware for
mounting to the wall/panel is provided by the
installer). The 4-point con guration is shown below.
For a 2-point configuration, mount the feet as
shown, but rotate the bottom feet 180 degrees so
that they are ush against the back of the enclosure.
Step 2. Install AcuRev1310 Series meter onto DIN rail inside the AcuRev1310-ENC
The AcuRev 1310 Series meter is shipped with a set
of two DIN rail clips included. These clips are already
installed into the slots on the back of the housing
from the middle, moving outward. Stopping pegs
must face the underside of the housing.
Run meter wiring through the holes drilled
previously. Wire the meter according to the
instructions in the meter installation guide.
Push the top of the meter onto the DIN rail.
Push the bottom of the meter onto the DIN rail until
there is an audible click.
. .
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
3
Page 4
Swing panel cover can be attached using the enclosed hardware.
Close the hinged lid and secure the clasp to close.
Screws are provided to
secure the hinged lid. Local
codes may require this
step to prevent opening by
unauthorized persons if a
locking mechanism is not
used. For added security,
the installer may also add a
locking mechanism.
Optional: Use included
hardware to secure the
hinged lid at all four
corners.
Optional: Attach a
locking mechanism
here (not included).
MAKE ENERGY USAGE SMARTER
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Loading...