AccuCold FS407LBI7NZADA, FS407LBI7NZ User Manual

CALIBRATED THERMOMETER/ALARM USER MANUAL

Features

 Thermometer simultaneously displays minimum, maximum and current temperatures
 The unit will provide a visual and audio alert when temperature rises above or falls below the

high and low set points

 The min/max feature is designed to monitor and store the highest and lowest readings until the

memory is cleared

 The temperature sensor is enclosed in a glycol-filled bottle, protecting it from rapid temperature

changes when refrigerator/freezer door is opened

 Low battery alert function ( battery symbol flashes)
 Rear slide switch to select oC or oF temperature display
 Measuring temperature range -30 ~ 70 oC ( or -22 ~ 158 oF)
 Accuracy : ± 0.5 oC (-10 ~ 10 oC or 14 ~ 50 oF), in other range ± 1 oC ( or ± 2 oF)
 Alarm setting and alert on /off function
 Sampling rate of 10 seconds
 Powered by a durable AAA lithium battery
 6 ft (185 cm) probe-connecting cable

SAVE THIS MANUAL FOR FUTURE REFERENCE

Felix Storch, Inc. │ Bronx, NY 10474│ Tel: [phone]│ Fax: [phone]

R006-12282018

Press the MODE/RESET button ONCE to reset Min/Max temperature record.
When the thermometer is sounding an alarm, press this button ONCE to turn off the
beeping sound.

From the main display screen:
Press ONCE to display high alarm temperature setting.

Press TWICE to display low alarm temperature setting.
Press THREE TIMES to display current temperature
reading.

When the thermometer is sounding an alarm, press this button ONCE to turn off.
However, the High-Alarm or Low-Alarm will still flash until the temperature goes
back to normal or the Low-Alarm function is turned off.

Main display screen

Package Contents

 Display unit
 Temperature sensor in a glycol-filled bottle
 Instruction manual

 Calibration certificate
 Lithium battery

*Remove the protective film that is applied to the LCD screen prior to using this product.

Parts and Controls/Features

Set Up

Battery Installation: Remove battery compartment cover located on the rear of the unit and remove

insulation strip from battery compartment. Follow the polarity (+/-) diagram in the battery
compartment. Replace the battery cover. The unit will beep and all segments of the LCD will be
activated.

Switching between Fahrenheit and Celsius: To change the temperature display scale from Fahrenheit

(oF) to Celsius (oC) and back, slide the oC/oF button located on the rear of the unit.

R006-12282018

To reset high alarm temperature setting and low alarm temperature setting, follow
instructions below.

High Alarm Temperature
Setting

From the main display screen:
Press HIGH/LOW key ONCE, then press MODE/RESET key to enter High
Alarm temperature setting mode. Use the up and down arrows to adjust

temperature accordingly.

Press MODE/RESET key ONCE to confirm the setting.

Low Alarm Temperature
Setting

From the main display screen:
Press HIGH/LOW key TWICE, then press MODE/RESET key to enter Low
Alarm temperature setting mode. Use the up and down arrows to adjust

temperature accordingly.
Press MODE/RESET key ONCE to confirm the settings.

By default the low and high alarm should be audible. To turn ALERT ON/OFF follow the instructions

below :

Audible High Alarm Setting

To make sure that the high temperature alarm is audible, press
HIGH/LOW key ONCE (to activate the HI-SET on the screen). Then

press the ALERT ON/OFF key ONCE to activate the HIGH-alarm
beeping sound. Press AGAIN to deactivate

Audible Low Alarm Setting

To make sure that the low temperature alarm is audible, press
HIGH/LOW key TWICE (to activate the LOW-SET on the screen). Then
press the ALERT ON/OFF key ONCE to
activate the LOW-ALARM beeping sound.
Press AGAIN to deactivate.
For an activated Hi-alarm and Lo-alarm
buzzer, the display will indicate Hi-Alarm
and Lo-Alarm as shown :

Operation

Programming the Alarms

To Use

 Once the Alarm Thermometer has been programmed, place the temperature sensor (in glycol bottle) in

the location to be monitored, such as inside a refrigerator or freezer. Attach thermometer to the door of
the unit with magnet on back of the thermometer, or place it on a table or shelf where it can be easily
seen and heard.

 Thermometer displays internal temperature of unit being monitored, as well as maximum and

minimum temperatures reached. The thermometer maximum and minimum readings reflect the

highest and lowest temperatures since the battery was inserted or since the RESET button was last
pressed.

 If the temperature measurement rises above or falls below the set temperature range, the alarm will

sound. To silence the alarm, press ALERT ON/OFF button.

 Set the high and low alarm temperature limits above and below the refrigerator/freezer operating

temperature to prevent false alarms. Refrigerators are designed to run between 2-8 °C (36-46°F) while
freezers run below -15 °C (5 °F).

R006-12282018

Displays „NP‟

The temperature sensor is not installed correctly.

Display screen not working

Make sure the battery is installed correctly. Battery may
need to be replaced.

“Low battery” indicator flashing

Battery may need to be replaced.

WARNING: This product can expose you to chemicals including Nickel

(Metallic) which is known to the State of California to cause cancer.
For more information go to www.P65Warnings.ca.gov

Troubleshooting

Care & Maintenance

• Do not disassemble the product, as product damage may result.

• Store the product where it will not be exposed to direct sunlight, dust or high humidity.

• Do not wash or expose the product to water or other liquids.

• Clean the product by wiping with a soft, dry cloth.

• Never use volatile or abrasive liquids or cleaners to clean the product.

• Do not drop the product or subject it to sudden shock or impact.

Customer Support

For technical support, please call 800-932-4267 (U.S. and Canada) or email

[e-mail]

For more information, please call ACCUCOLD at 718-893-3900 (U.S. and Canada). See us
on the web at www.summitappliance.com

For re-calibration and certification questions, please email us at [e-mail]

Limited Warranty

SUMMIT products have a limited warranty period of 1 year against defects in materials and
workmanship from the date of purchase. Accessory items and sensors have a limited warranty
of 3 months. Repair services have a limited warranty period of 3 months against defects in
materials and workmanship. SUMMIT shall, at its option either repair or replace hardware
products that prove to be defective, if a notice to that effect is received within the warranty period.
SUMMIT makes no other warranties or representations of any kind whatsoever, expressed or
implied, except that of title, and all implied warranties including any warranty of merchantability
and fitness for a particular purpose are hereby disclaimed.

Summit, Div of Felix Storch, Inc. • Bronx, NY 10474 • Tel: [phone] • Fax: [phone]

R006-12282018