Acclaim Lighting X-Power TV User Manual
User Instructions
Descriptions:
Congratulations with your purchase of this product.
Read this manual carefully before using our Acclaim Lighting X-Power TV. The X-Power TV is a combination
of a control interface and tension provider for our X-CHIP LED PCB modules. A maximum of 24 channels
can be controlled separately. Its high frequency function is suitable for CCD cameras pick up facility.
Delivery packet:
Check for transport damage.
You should be in possession of the following items:
1 X-Power TV
1 manual
Should you discover transport damage after unpacking the equipment, inform the hauler immediately.
Never connect a damaged device. You may also contact your supplier.
Controls & Functions:
Front panel view
R
CAUTION
Risk of Electric Shock
DO NOT OPEN
Ne pas ouvrir. Risque de choc electrique
Warning :
This unit must be grounded
POWER IN:
110-120VAC, 3.2A / 220-240VAC, 1.6A
50/60Hz 150W
FUSE:
T3.15A 250V 5x20mm
Serial Number:
VOLTAGE-SELECT
115V
1. Fuse holder Fuse T3.15A 250V 5x20mm
2. Power In AC110-120V, 3.2A/ AC220V-240V, 1.6A 50/60Hz, 150W
3. Selection tension Selection of tension
AC110-120V/ AC220V-240V,50/60Hz, 150W
4. Power switch ON/OFF
Rear panel view
DMX IN
1
1
1
3
3
3
THROUGH
2
2
2
1=Ground
2=Data3=Data+
2
2
2
PUSH
PUSH
PUSH
3
3
3
1
1
1
DMX
POWER
7
8
1
Red
Blue
Red
Green
Blue
+24V
GND
5 6
3
Red
Green
Blue
+24V
GND
42
Red
Green
Blue
+24V
GND
OUTPUT: 6A/CH. TOTAL 6A MAX.
9
5
Red
Green
Green
Blue
+24V
+24V
GND
GND
5. DMX LED
Green LED (flashing) indication for DMX signal.
Quick flashing: an Acclaim Lighting Setup tool is updating.
R
Slow flashing: DMX signal active.
6. Power LED
Red LED (power) indication for presence of tension.
7. DMX / Programming input
XLR chassis part male, 3-polar for DMX connection.
8. DMX output/Thru (connection)
XLR chassis part female, 3-polar for DMX through.
1
FUSE
POWER
Made in PRC
POWER IN
2
43
6
Red
Blue
7
Red
Green
Blue
+24V
GND
8
Red
Green
Green
Blue
+24V
+24V
GND
GND
Acclaim Lighting - Los Angeles, CA 90058
www.acclaimlighting.com
24-004-1915-00
Rev 2.0
9. 24V DC outputs
8 terminal output connector, 5-polar for connecting X-CHIP LED modules 24V DC.
Note: Never connect the DMX signal and the Setup Tool to an XLR 3-polar input or output simultaneously.
This can severely damage your X-Power TV.
Connecting the tension provider:
Check whether or not the Voltage Select switch has been set correctly.
Note: If Voltage Select is set to 110V, do NOT connect a 230V power supply. This can severely damage
your X-Power TV. The X-Power TV comes with a complete power cable. The device is powered by an
IEC cord which fits into the power adapter (1) on the backside of the device. Keep pushing the IEC until
it is fixed into position in the adapter. The device can be turned on by means of a power switch. An indicator
shows whether the device is turned on or off.
Connecting the X-CHIP LED PCB modules to the X-Power TV
DMX Controller
A Setup Tool
Or
X-Power TV
(A Driver Unit)
XB-R1
X-CHIP PCB modules
DMX
through
NOTE:
A maximum loads of 50pcs X-CHIP PCB modules are allowed
on a single output and the maximum amount connected modules
distributed over all 8 outputs must not exceed 100pcs.
Configuration:
1. Maximum amount of connected X-CHIP LED PCB modules
A maximum of 24 channels (8x RGB channels) can be controlled separately. The maximum amount of
connected modules must not exceed 100. Please note: only 50 modules are allowed
on a single output.
X-CHIP LED PCB
2. Connector configuration
The DMX configuration is depicted below. The DMX connections consist of one XLR 3 male connector
(input) and one XLR 3 female connector (transited output) .
The XLR 3-polar connector:
1 = GROUND
2 = DATA -
3 = DATA +
3. Connector configuration outputs
Chassis part XLR-3 male Chassis part XLR-3 female
The output configuration is depicted below. The output connections consist of eight 5-polar terminal
connectors.
The 5-polar terminal connector:
1 = Blue
2 = RED
1 2 3 4 5
3 = GREEN
4 = +24V
5 = GND
5-polar terminal output connector
- Page 2 -
Loading...