Accent Advanced Systems USMART10 Users Manual

ACCENT ADVANCED SYSTEMS S.L.U.

e-mail:[e-mail]
www.accent-systems.com

uSmart 10

Features

• Bluetooth LE Module

• Based on TI®CC2540

• User programable with BLE profiles

• FCC, IC and CE compliant

Product image

Applications

• BLE compatible accessories

Pinout

uSmart10 – Version 2.0

Bluetooth Low Energy ® module

(TOP VIEW)

www.accent-systems.com pag.1/6

ACCENT ADVANCED SYSTEMS S.L.U.

e-mail:[e-mail]
www.accent-systems.com

uSmart10 – Version 2.0

PIN NUMBER

INTERNAL NAME

1

P24 / OSC32K

2

P23 / OSC32K

3

DCLK

4

DDAT

5

P20

6

P17

7

P16

8

PUSBCL_P

9

PUSBCL_N

10

D_USB

11

P15

12

P14

13

P13

14

P12

15

P11

16

GND

17

P10

18

PG_EXT_RESET

19

VCC

20

P07

21

P06

22

P05

23

P04

24

P03

25

P02

26

P01

Bluetooth Low Energy ® module

www.accent-systems.com pag.2/6

ACCENT ADVANCED SYSTEMS S.L.U.

e-mail:[e-mail]
www.accent-systems.com

uSmart10 – Version 2.0

27

P00

Bluetooth Low Energy ® module

Firmware upload interface

• DCLK, DDAT, VCC, GND and PG_EXT_RESET is the interface to upload new firmwares to module.

Optional low frecuency clock

• Opcional 32.768 Hz clock can be connected to perform 500 nA of current consumption in low power mode. Crystal may be
connected in pins 1 and 2.

◦ Maximum crystal tolerance +-40 ppm.
◦ ESR 40 to 130 kOhms
◦ Maximum shunt capacitance 2pF.
◦ Load capacitance up to 16pF.

Dimensions (in mm)

www.accent-systems.com pag.3/6

ACCENT ADVANCED SYSTEMS S.L.U.

e-mail:[e-mail]
www.accent-systems.com

uSmart10 – Version 2.0

Specification

Compilance

FCC

IC

CE

RoHs

Bluetooth Low Energy ® module

Compilance information

www.accent-systems.com pag.4/6

ACCENT ADVANCED SYSTEMS S.L.U.

e-mail:[e-mail]
www.accent-systems.com

Label information

uSmart10 – Version 2.0

Bluetooth Low Energy ® module

www.accent-systems.com pag.5/6

ACCENT ADVANCED SYSTEMS S.L.U.

e-mail:[e-mail]
www.accent-systems.com

uSmart10 – Version 2.0

Bluetooth Low Energy ® module

1. FCC Caution:

"Changes or modifications not expressly approved by the part responsible for compliance could
void the user's authority to operate the equipment."

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

2. FCC Statement:
"This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:

—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

—Consult the dealer or an experienced radio/TV technician for help."

www.accent-systems.com pag.6/6