Abu Garcia Revo MGXtreme User Manual

REVO MGX/MGXtreme LOW PROFILE INSTRUCTION MANUAL

a. Congratulations

b. Pictures of Components

c. Family Info

d. How to Fill the Spool with Line

e. Drag Adjustment

f. Spool Tension Knob

g. Removing the Sideplate

h. Reel Function

i. Maintenance

j. Revo® Shop Accessories

k. Warranty Information

Star drag

Line guide

Handle

Spool

Spool Tension Knob

Palm Sideplate

Thumb Screw

Knobs

Thumb Bar

Brake Dial

Handle Sideplate

Gear Box

Frame

IVCB-IV™ Brake Dial

Handle Nut

Maintenance Port Screw

Nut Retainer Screw

Trim Ring

Handle Knob Caps

Nut Retainer

A. CONGRATULATIONS:

Thank you for purchasing one of the world’s most advanced low profile reels. The combination

of low profile design, ultra-lightweight materials and precision engineering makes Abu Garcia®
THE choice for serious anglers around the globe. These reels are widely used by pros on the
tournament circuit, guides, record seeking experts and anglers who demand the very best from
their equipment. Rely on Abu Garcia® quality and dependability to keep the fun in fishing.

The following guide will explain how to get the most out of your new Revo® MGX/MGXtreme
low profile reel. Each element is described by its name and function. Some features are not
found on every reel model. Read these instructions carefully before using your reel to ensure a
proper understanding of its operation.

B. COMPONENTS:
Include:

C. THE REVO® MGX & MGXtreme:

The combination of an enhanced compact design with our ground-breaking X-Mag alloy frame
and C6 carbon sidelplates produce the evolution of ultra-lightweight, low profile reel technology.
Revo® MGX & MGXtreme low profile reels feature the adjustable IVCB-IV brake system
provides precision brake adjustments, allowing anglers to cast a wide variety of baits including
lightweight finesse lures.

D. HOW TO FILL THE SPOOL WITH LINE
Revo® MGX and MGXtreme low profile reels are designed for monofilament, braid and

fluorocarbon lines. Personal preference and fishing conditions will determine line selection.
Begin by passing the line through the guide located on the front of the reel. Secure the line to the
reel using the arbor knot. Control the filler spool by inserting a pencil into the spool hub. While
maintaining tension on the line with your fingers, wind the reel handle and continue to fill with

line to approximately 1/16” (1.5 mm) below the top of the reel spool for best results (show

picture). Do not overfill. (CLICK HERE to learn how to tie the arbor knot in this video)
Braided Line

Some anglers prefer to add a monofilament backing to the reel spool before attaching braided
line. This helps reduce line slip. Using the above instructions, fill the spool with enough
monofilament line to cover the spool. Tie the tag end of the monofilament backing to the
braided line using a uni-to-uni knot, Albright knot or equivalent. Continue to fill the spool with
braid to approximately 1/16” (1.5 mm) inside the upper lip of the spool. Do not overfill.
(CLICK HERE to learn how to tie the uni-to-uni knot in this video)

E. DRAG ADJUSTMENT
The Revo® MGX and MGXtreme are capable of up to 12 lbs of smooth and reliable drag

tension. Control the amount of drag by turning the adjustment star inside the reel handle.
Rotate the star clockwise (right) to increase drag or counterclockwise (left) to decrease drag. For
best results the drag should be adjusted to approximately one-third of the breaking test of the line
being used. This can be accomplished by tying the line to a spring scale for precise adjustment.
Make sure the reel is first mounted on a rod and the line has been run though the rod guides
before tying to the scale. The drag should always release before the line reaches its breaking
point. Factors such as line type, technique and fishing conditions may require adjustment to
these recommendations. Any drag setting above half of the line strength risks line breakage.

If a spring scale is unavailable, tie the line to a secure point. With the rod tip up (about a 45
degree vertical angle), apply pressure by turning the handle. Gradually tighten the drag