All specifications and figures are subject to change without notice.
All trademarks and logos are the properties of their respective holders.
G SERIES
Read prior to assembly.
安装前请仔细阅读本说明书。
lire avant l’assemblage.
Lesen Sie die Anleitung vor
dem Zusammenbau.
Leer antes de ensamblar.
Leia antes de montar.
Прочитайте до начала сборки.
조립 전에 읽어 보시기 바랍니다.
アセンブリの前にお読みください。
Table of Contents - English
What’s Included
Chair Components
Accessories
Assembly Instructions
Chair Assembly
How to install the head cushion
How to install the lumbar support
Detailed Dimensions
Dimensions Diagram
English
1
2
3-6
7
8
9
Gear Series
Basic installation and operation instructions for Clutch Brand G-Series chairs. Copywrite 2016©.
For more detailed instructions, including assemblying videos, visit www.clutchchairs.com/assembly_instructions.
Care & Use Instructions
Care & Use Instructions
10
01
What’s Included - Chair Components What’s Included - Accessories
Please ensure that all of the components listed below are included in the package.
Contact your local reseller if anything is not included.
01
English
Side Cover x 1 Head Cushion x 1 Lumbar Support x 1
Mechanism x 1
Seat Pan x 1
Gas lift & Cover x 1
Backrest x 1
Chair Base x 1
Note: Required M8 bolts are already installed in their corresponding sockets.
1 2
i.e. - 4 bolts in the backrest and 4 bolts in the underside of the seat pan.
Castor x 5
Side Covers x 1
Chevron Insert x 5
M8 Allen Key x 1
Please note: Use of the head cushion and lumbar support are optional.
Clutch Chairs Ltd recommends using them for 2-3 days before deciding
whether you prefer to use each item or not.
02
Assembly Instructions - Chair Assembly Assembly Instructions - Chair Assembly
1. Place the base upside down on a rm but padded surface.
We recommend placing a piece of foam from the box on the oor.
Firmly insert the 5 castors into
the corresponding holes.
3. Insert the faux bolts
into the holes in the
center hub of the base.
01
5. Remove the 4 M8 bolts that are already installed on each side of the backrest. Then position
the backrest between the hinges that are attached to the seat pan. Reinstall the 4 M8 bolts into
their original holes once the hinges are in place. Be sure to use your ngers to start the bolts and
be careful to ensure they are not cross threaded. Proceed by rmly tightening the bolts with the
allen key provided.
English
4 X
M8 bolts
M8
M8
2. Turn the base right
side up and insert the
colour accent chevrons
in the end of each arm
of the base.
5 X
4. Insert the thick
end of the gas lift
into the center
hole of the base
and slide the plastic
cover into place.
3 4
02
01
Assembly Instructions - Chair Assembly Assembly Instructions - Chair Assembly
6. Install the plastic side covers using the Phillips
screw driver head on the allen key provided. Be
sure not to over tighten as you may crack the
plastic cover.
5 6
7. Remove the 4 M8 bolts already installed on the
underside of the seat pan. Position the mechanism
to align with those same holes and reinstall the bolts.
Again, be sure to start the bolts using your ngers to
ensure they are not cross threaded. Proceed by rmly
tightening the bolts with the allen key provided.
4 X M8
Important Note: Ensure that the mechanisn is orientated
correctly, front to back, as per the diagram above.
8. Connect the upper portion of the chair
to the base by inserting the gas lift into
the corresponding hole in the mechansim.
Keep the upper part of the chair as vertical
as possible to ensure the gas lift seats
properly into the mechanism.
Congratulations!
You’ve just completed
assembly of your new
Clutch Chair.
English
02
Assembly Instructions - How to install the Head Cushion
Place the straps completing around the upper portion of the backrest and secure them with the
side release plastic buckle.
Then tighten the strap to hold the head cushion in the desired position.
Neatly roll/fold the excess strap to about 2 inches wide and tuck it under the black rubber band.
7 8
01
Assembly Instructions - How to install the Lumbar Support
The lumbar cushion is designed to rest on the seatpan, it does not physically attach to the chair.
The size and ergonomic design create the perfect support for your lumbar spine. If you prefer the
cushion to sit a little higher on your back you can manually move it up while you are in a seated
position. Simply sit as you normally would then lean forward slightly, position the lumbar cushion
exactly where you want it then lean back and sit normally.
English
Detailed Dimensions - Dimension Diagram
A
B
I
C
F
K
D
E
9 10
J
G
H
545
A
270
B
70-100
C
320-370
D
525
E
F
370-450
G
90
H
790
I
270-350
J
550
K
350
Units - mm
How to get the most out of your new Clutch Chair
Cleaning Instructions
Regular cleaning with a slightly damp mircober cloth or terrycloth rag will keep your chair looking good for
years to come. Do not use any harsh chemicals or cleaners. Immediately wipe o any liquids or foods that
may be spilled on the chair.
A mild foam upholstery cleaner is recommended for stain removal on fabric chairs. Be sure to test any
cleaner on an inconspicuous portion of the chair rst.
Care & Use Instructions
English
1. Keep out of direct sunlight. Long term exposure to UV rays will fade and weaken the upholstery.
2. When moving the chair be careful not to collide with surrounding objects.
3. Sit only on the seat pan to avoid risk of tipping the chair. Exercise extra caution when the chair is
reclined.
4. Do not use excessive force when operating the height and tilt control levers. Only light to medium
pressure should be required.
5. Do not apply excessive force of weight to the armrest.
6. Do not exceed the chairs recommended weight limit.
Pinch Point Warning - Use caution when operating the lever
that adjusts the angle of the backrest.
0403
Loading...