The lightning flash with arrowhead, within an equilateral
triangle, is intended to alert
the user to the presence of
uninstalled “dangerous voltage” within the product’s enclosure. This voltage may
be of sufficient magnitude
to constitute a risk of electric shock to persons.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The exclamation point
within an equilateral triangle is intended to alert
the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature accompanying the appliance.
IMPORTANT SAFETY INSTRUCTIONS
1.Read these instructions.
2.Keep these instructions.
3.Heed all warnings.
4.Follow all instructions.
5.Do not use this apparatus near water.
6.Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
7.Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
8.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong is provided for
your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
9.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
10. Only use attachments/accessories sp
11. Unplug this apparatus during lightning storms or when unused for long periods of
time.
12. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been
In determining the location for your
Megatouch Gametime™ video game, consideration must be given to a suitable,
grounded electrical outlet. Since the game
is a computerized device, it should be connected to a separate grounded circuit. If a
separate circuit is not available, care should
be taken to provide a clean and constant
voltage. As a basic guideline, never connect the unit to a circuit that also supplies
power to freezers, coolers or other high
power consuming and electrical noise-generating equipment. Place the game in a location where nothing will interfere with proper
ventilation. The game should not be exposed
to any dripping or splashing liquids. Objects
filled with liquid should not be placed on the
unit.
WARNING - To reduce the risk of fire or
electric shock, do not expose this apparatus to rain or moisture. The power
cord on the rear of the unit is the disconnect device and must remain
readily accessible after installation.
Setting up your Game
1.After removing the game from the carton, plug the game into a standard AC
outlet.
NOTE: All packaging materials should
be retained in the event the game needs
to be sent in for service.
2.Turn the power switch at the back of
the game to ON and wait for completion of the boot-up sequence. The game
will display the Player Menu Screen.
3.The machine has been preset at the
factory and therefore should not need
to be adjusted; however, it is recommended that the screen be calibrated
(see Touchscreen Calibration).
4.There are many custom settings available for the game. To customize the
settings, follow the software instructions in this manual.
The Megatouch Gametime unit has an
Ethernet coupler installed in the rear of the
game (see Figure 1). The coupler can be
used for broadband Internet connection or
linking two or more games together for headto-head play. The game also has a wireless
adapter which can be used to automatically
wirelessly link to another game or wirelessly
connect to a broadband Internet connection
(this requires the purchase of an 802.11
wireless router). An optional keyboard upgrade is also available for purchase through
your local authorized dealer (part number:
KAV-100-014-01). The keyboard allows you
to easily type text in a Web browser. There
is also a centronics connector on the back
of the game which is used for future software upgrades.
Control Board Compartment
The control board compartment is located at
the rear of the game (see Figures 1 and 2).
Loosen the two thumbscrews to open the
compartment. The buttons on the control
board are explained below.
SETUP
Press SETUP to access the software options. These options are explained in the
software section of this manual. If SETUP is
pressed during boot-up, the on-screen DIP
switch program will launch. Consult the DIPSWITCH SETTINGS section of this manual
for more information.
CALIBRATE
Pressing the CALIBRATE button will take
you through the steps to calibrate the
touchscreen. This is sometimes necessary
if the touchscreen is not responding properly to touch. See Touchscreen Calibra-
tion for detailed instructions.
MONITOR CONTROLS
The five buttons labeled Auto, Exit, Left,
Right, and Menu adjust the monitor settings.
See Monitor Adjustment Procedure for
detailed instructions of each button.
General Care and Maintenance
Touchscreen Calibration
•Press the CALIBRATE button, located
in the control board compartment (see
Figure 2). Touch the center of the first
cross that appears on the screen.
Once you release your finger, a second cross will appear.
NOTE: You must hold your finger on
the circle for approximately 2 seconds
for the calibration to be recognized.
•Touch the center of the second cross
that appears on the screen.
•Once the second cross is touched and
released, another cross will appear on
the screen. To test the calibration of
the screen, touch the cross with your
finger and slowly drag your finger
around the screen. The cross should
follow your movement.
The vertical/horizontal controls and brightness/contrast controls are located on the
control board (see Figure 2).
Pressing the button labeled Menu on the
control board will show an on-screen display of the monitor settings. Use the Left
and Right buttons to move through the menu.
Touch Menu to select the option you want to
change. Use the Left and Right buttons to
change the option. Then press Menu again
to deselect the option. Auto will automatically adjust the size and brightness. Touch
the Exit button to exit. Adjust the monitor
controls until the screens look as suggested
in the following steps:
1.Set the game to the Checkerz game
screen.
2.Adjust the vertical and horizontal size
and vertical and horizontal position to
make sure that the game screen fills
the monitor screen and that the game
screen is centered.
3.Adjust the brightness and contrast controls until the top sets of checkers are
a rich red and the bottom set are a dark
gray. The feet on the “Checkerz”
character should be white. (Adjusting
the brightness and contrast can also
correct a lack of sharpness.)
Cleaning the Cabinet
•The cabinet should be cleaned with a
dry cloth and mild detergent. Always
apply the cleaner to the cloth and not
directly on the game. Liquids could
enter the cabinet and damage electronics inside.
Cleaning the Touchscreen Monitor
•The touchscreen glass should be
cleaned with a damp cloth and isopropyl alcohol or a non-ammonia cleanser.
Do not use any abrasive or vinegar-
based cleansers, as they will damage
the touchscreen glass. Always apply
the cleaner to the cloth and not directly
to the glass. Liquids could enter the
cabinet and damage electronics inside.
NOTE: DO NOT USE ANY ABRASIVE
SOLVENTS, ACID OR VINEGAR-BASED
CLEANSERS ON THE TOUCHSCREEN
OR SIDE DECALS. SUCH CLEANSERS
COULD HARM THE TOUCHSCREEN
AND ERASE THE DECALS. BE CAREFUL NOT TO USE COMMERCIAL
CLEANERS CONTAINING ANY OF
THESE SUBSTANCES.
Cleaning the Fans and Vents
•The fans and vents should be cleaned
of any dust and grime on a regular
basis to ensure proper ventilation of
the game.
•To ensure proper operation of the
game, it is important that all fans are
operating correctly and that the airflow
is unobstructed. Make sure nothing is
placed next to the fan vents that would
inhibit the flow of air. Also, if any fans
are not operating, it is important that
the game be sent in for service.
Watchdog Timer
This game has been equipped with a feature that allows it to automatically reboot if it
encounters a problem. When the watchdog
timer is enabled, it will reboot the machine
within 2 minutes after a failure, allowing the
game to automatically reset itself if a problem arises without needing a technician
present.
PM0503-10 MEGATOUCH GAMETIME OWNER’S MANUAL 4
PUZZLES
Box Glide
Lookout
Fast Lane
Tai-Play
Castle Bandits
Chug 21
Funky Monkey
Quik Match
Pix Mix
TV Guide® Crossword
Memoree
Match ‘Em Up
Super Lone Star
Lone Star
Tri Castles
Four Play
Magic Charms
Puzzle Merit-thon
Sudoku 6
Motor Match
Edit the game list (choose which games are available and
in what category they appear on the Category Menu).
Select options for individual games. NOTE: The Games
Options Screen is password protected. See the
Games Menu section for more information.
Hi Scores
•
View/Clear Hi Scores
•
Options
Touch CLEAR ALL GAMES to clear all high scores or
select a particular game to edit high scores for that game.
System
•
Set Time
•
Security Setup
•
Volume Control
• Set 6 Star PIN
• Data Transfer
• Options
Set the game clock, security PIN, game volume, 6 star
PIN, and system options such as language control and 6
Star Enable.
Diagnostics
• Video Test
• I/O Test
•
Touchscreen
Calibration
• Touchscreen Test
•
View System Log
•
Checksum Test
•
System Info
• Verify Databases
• Enters the Video Test to display the test screens.
Touch the screen to cycle through the test.
• Tests the function of the I/O board and DIP switches.
•
Follow the instructions on the screen to calibrate the
touchscreen.
• Touch the crosshairs on the screen to make sure it is
accurately calibrated.
•
Displays operations performed by the game.
•
Checks the hard drive for missing or corrupted files.
•
Gives details about various hardware components in
the game.
• Only use on the advice of Merit Technical Service.
TournaTime
•
General Info
• Connection Log
• Ethernet Setup
• Set Update Time
•
Update From Server
•
Clear Database
Enters the TournaTime Setup Screen. From this menu,
you can set up your local area network for linking games
and also configure your Internet connection settings and
update Tournament information.
GTnet
• Hot Topics
•
Options
• Enter screen to select Hot Topics games.
•
Enable Hot Topics in this screen.
NOTE: This button only appears if a GTnet subscription has been purchased.
Main Menu
The Main Menu can be accessed by pressing the SETUP button(located in the control board
compartment at the rear of the game) or through the 6 Star feature (touch Options on the
Player Menu Screen, then touch 6 Star). Use the Main Menu to set up all software options.
NOTE: For help with the Options within any menu, touch the green “?” buttons.
FIGURE 3 - MAIN MENU
A summary of the Main Menu functions appears in the following table. For more detail, see
the corresponding sections of the manual.
The game list and game options are programmed using these screens. The first
screen shows the various game categories
and allows access to general settings for
all games.
Enable All Games Into Menu: Turns on
all games.
Factory Default Games Into Menu: Returns the Game Setup to its default settings.
To customize a particular game list, first select a category in the initial Game Setup
Screen. On the second screen, touch ClearAll to clear the game list. Choose the menu
position you want a particular game to occupy, then touch the desired game name on
the list at the bottom of the screen. Repeat
until all desired games appear in the menu (a
game cannot appear in a game list more than
once). Games already displayed in the menu
will be red.
Game Options
The Options screens in the Games Menu
are password protected. See SecuritySetup for PIN information. Touch the green
“?” button next to the option for more information on any option. In this menu, you can
set options for all games, as well as enable
or disable Erotic games.
Once you attempt to enable the Erotic category, an Erotic disclaimer will appear. Read
the disclaimer text and select I Accept to
enable the category.
NOTE: When Kids’ Club is enabled, the
Erotic category will automatically dis-
able and vice versa.
When you touch a category name, the next
Game Setup Screen shows the game positions available for that category, with the list
at the bottom showing all games available
for the selected category.
The Game Setup Screen also allows you to
make these general changes:
Default Games: Resets the selected category menu to its default game settings.
Clear One: Clears a selected game from
the Player Game Menu.
Clear All: Clears all games from the Player
Game Menu.
Enable All Games: Turns on all games
within the selected category.
7 MEGATOUCH GAMETIME OWNER’S MANUAL PM0503-10
Hi Scores Menu
View/Clear Hi Scores
Use this screen to manage hi scores. The
first screen allows you to clear all scores
for all games by touching Clear All Games.
To edit the hi scores by game, select a game
on the first screen. Touch Clear All to remove all hi scores for that game or remove
an individual score by touching Clear One.
Options
Enter this screen to enable or disable the
Auto Clear Hi Scores and No Names in
Hi Scores options.
System Menu
Set Time
The Set Time Menu allows you to set the time on the game.
Time is shown in 24-hour, "military" time (e.g. 5:00pm = 17:00).
Use the arrows on either side of the fields to set the time and
date.
Security Setup
Modify the pin that protects the Games Options Menu. Enter the
existing PIN (the default is
0000
), then enter a new 4-digit
number and touch
SET
on the keypad. The game will prompt
you to re-enter your PIN for confirmation.
Volume Control
Touch the volume control button to adjust the volume up or down.
This screen allows you to sample the sound volume without
exiting the screen.
Set 6 Star PIN
Set the 6 Star PIN (between one and six digits) using this screen.
The default 6 Star PIN is
1234
. 6 Star allows you to access the
SETUP Menu by touching
Options
on the Player Menu Screen,
followed by the
6 Star
button and then the PIN. To enable this
feature, touch Options on the System Menu and choose
Enable
6 Star
.
Data Transfer
This button is inoperable. Data Transfer functions are not
available on the Gametime unit.
Video Test Touch the screen to cycle through a series of video test screens.
I/O Test
Tests the SETUP and CALIBRATE buttons. A green light next to the
appropriate button will register each time that item is tested, and the
number next to the item should increment by one with each test. The
I/O Test Screen also displays which DIP switches are on or off.
NOTE: The DIP switch on/off status feature does not apply for
Gametime.
Touchscreen
Calibration
Follow the on-screen instructions to calibrate the touchscreen.
Touchscreen Test
Allows you to check the touchscreen calibration accuracy. The
crosshairs should follow your finger exactly when you move it across the
screen. If the crosshairs do not accurately follow, you should perform a
touchscreen calibration.
View System Lo g
Displays a log of all operations performed by the game since the log
was last cleared. This information is helpful for customer service
when troubleshooting your game.
Checksum Test
Checks the hard drive for missing or corrupted files. With
STOP ON
ERROR?
set to
YES
, a message indicating which file is corrupted will
be shown whenever the game encounters an error. With
STOP ON
ERROR?
set to NO, a list of corrupted files will be displayed when the
test is complete. If errors are detected, the software on the drive may
need to be reloaded. If this does not solve the problem, the drive may
require replacement. The test could take up to 30 minutes.
System Info
Gives details about the following:
• processor type and speed
• motherboard manufacturer
• amount of memory
•
Ethernet card manufacturer
• sound chip type
• video chip type
• touchscreen manufacturer
• hard drive manufacturer
and capacity
• modem part identification
number
• fan speed
• status
•
PSOC version
Verify Databases
Only use on the advice of Merit Technical Service. An
The My Merit feature allows individual players to create custom accounts, which are
accessible via PIN numbers. Accounts can
be created by touching the My Merit button on the Player Menu Screen. Log in to
your account through the Options button
on the Player Menu screen and have personal game data stored on the machine,
including hi scores and the number of
games played in My Merit mode for the last
year.
Once you have logged in to your My Merit
account, you can perform the following functions:
View High Scores: Touch this button to
display the high score for each game you
have played.
View Gameplay Data: Touching this button will display each game played as well
as the number of times each game was
played.
Log Out: Sign out of My Merit and return
to the Player Menu Screen. Individual
gameplay and scores will not be tracked.
Log In As Another Player: End your session and allow another player to immediately
sign into My Merit.
Play Games: To keep track of your
gameplay, log in to your account and then
touch Play Games.
Follow these instructions to connect your
game to a broadband Internet connection.
Connecting your machine enables you to
purchase additional games via the Internet.
You can also sign up for MegaWeb,
TournaTime, andHot Topics (see GTnetContent for more information).
NOTE: To wirelessly connect your
game(s), skip to “Wireless Broadband
Internet Setup”.
Your broadband Internet connection should
already be connected and configured using
the instructions provided by your Internet
Service Provider and router manufacturer
before continuing with this installation.
NOTE: A router with a switch is required in order to connect multiple
computers and/or games to a broadband Internet connection.
1.Turn off the game.
2.Connect the Ethernet cable to the
Ethernet coupler at the back of the
game (see Figure 1).
On-Screen Internet Configuration
7.Remove the two thumbscrews securing the control board compartment and
open. Press the SETUP button located
on the control board. (You can also
access SETUP through 6 Star.)
8.At the MAIN MENU, touch the
TournaTime button. The first time you
enter this menu, you will be prompted
to select your time zone. Once a time
zone has been chosen, you will return
to the TournaTime Menu.
9.From the TournaTime Menu, touch the
Ethernet Setup button (see Figure 9).
To Enter This Screen, Touch
“TournaTime” on the Main Menu.
3.If you are networking your unit to share
an Internet connection with additional
games or a computer, connect the free
end of the Ethernet cable to the router.
Otherwise, directly connect the
Ethernet cable to the modem supplied
by your Internet Service Provider, and
proceed to step 5.
4.Complete the router installation using
the instructions provided with your
router.
5.Restore power to the game.
6.Continue with On-Screen InternetConfiguration to complete the
nection settings on the game.
10. Select Automatic or Manual, depending on how you are connecting to the
server:
Automatic: The automatic setting is
for cable or DSL connections using
dynamic IP addresses. Contact your
Internet service provider if you are unsure of what kind of IP address they
use. For Automatic connections, continue with step 11.
Manual: The manual setting is for cable
or DSL connections using static IP addresses. Contact your Internet service provider if you are unsure of what
kind of IP address they use. For Manual
connections, continue with step 13.
Automatic Only
11. After selecting Automatic, press the
Setup button. The game will prompt
you to confirm the default Server IP,
Primary DNS and Secondary DNS information. Touch the NEXT button to
accept these defaults. A screen asking, “Do you want to continue?” will
appear. Select NO, then touch the X on
the Internet Setup Screen to return to
the Player Menu Screen.
Manual Only
13. After selecting Manual, press the
Setup button. The game will then
prompt you to enter the Static IP Address. Enter the Address given to you
by your service provider and touch the
NEXT button. Then, enter the Gateway given to you by your service provider and touch the NEXT button. The
Server IP, Primary DNS Address and
Secondary DNS Address will already
be filled out. Touch NEXT to accept the
default information. Touch the NEXT
button to accept these defaults. A
screen asking, “Do you want to continue?” will appear. Select NO, then
touch the X on the Internet Setup
Screen to return to the Player Menu
Screen.
14. Press the Merit Link button. If your
connection was successful, a registration page will appear.
15. Continue with the GTnet Content and
Merit Link User Guide sections of
this manual for a description of features and instructions on how to get
started.
Press the Merit Link button. If your
connection was successful, a registration page will appear.
12. Continue with the GTnet Content and
Merit Link User Guide sections of
this manual for a description of features and instructions on how to get
started.
1.Install your wireless router, using the
instructions provided with the router.
When the router installation is complete,
plug in the game and turn on the power.
2.Access the Main Menu Screen through
the SETUP button or 6 Star menu.
3.Touch the TournaTime button. The
game will prompt you to enter the time
zone. Scroll through the list to find your
time zone and select it by touching it.
The game will return to the TournaTime
Menu.
4.Touch the Wireless button next to
(LAN) Local Area Network Connection to advance to the Internet Setup
screen.
5.Touch Configure Device and then
choose from the following options to
network your games:
Auto Detect Network: The system
will find and connect to the nearest
available wireless network. This is the
easiest way to connect.
Search for Networks: Looks for all
available wireless connections. Select
a connection from the list to proceed.
Secured connection: Choosing a
“locked” device will prompt a key (password) request. If the selection is your
own network, use your network password to gain access. If not, this indicates an outside wireless network that
has been encrypted and is not accessible.
Unsecured connection: You will be
prompted to enter interface information.
Accept the default values, or consult a
network advisor to manually configure
these settings.
Ad-Hoc Network: This is only for linking games, not for connecting to the
server for MegaNet.
NOTE: If you have chosen Ad-Hoc Network, you will be prompted to enter the
SSID (network name). Create a name
for your network and enter your network and enter that same SSID name
for all games that you want to link. You
will also be required to manually configure these settings, consult a network
advisor.
Custom Configuration: Touching
this button will prompt the user to enter
the SSID (network name) for manual
setup of the wireless connection.
NOTE: Wireless Internet connection
does not require Manual Configuration. Only users who have changed the
default SSID during router installation
should change the SSID. Consult the
instructions supplied with your wire-
less router for more information.
NOTE: If you have chosen Custom Con-
figuration, you will be prompted to enter
interface information. We suggest you accept the default values. If you want to manually configure these settings, consult a network advisor.
6.Once you have chosen your network
connection and the game returns to the
Wireless Device Setup Screen, reboot
the game in order to ensure that your
network is properly established.
7.When the game boots back up, press
the Merit Link button on the Player
Menu Screen. If your connection was
successful, a registration page will
appear. If not, check the troubleshooting guide.
8.Continue with the GTnet Content and
Merit Link User Guide sections for
a description of features and instructions on how to get started.
To purchase additional games or subscribe
to GTnet, click on the Merit Link button on
the Player Menu Screen. Your game must
be connected to the Internet. Complete the
registration process and accept the software license agreement to launch the
Gametime Web site. If you do not accept,
you will not be able to advance beyond the
registration page to shop for games.
NOTE: For step-by-step instructions on
how to register and conduct purchases
through Merit Link, see the “Merit Link
User Guide” section of this manual.
Follow the instructions on-screen to select
and purchase games for your unit. Credit
card and PayPal are the acceptable forms
of payment. Once the payment is approved,
an application will be sent to the unit to enable the purchased games. If the unit is
disconnected before the download is complete, it will be sent during the next call-in by
the unit (default call-in time is 3:00 am).
A confirmation E-mail, including the list of
items purchased, will be sent from the Merit
server. Following a successful download,
a screen will display prompting the user to
reboot the machine to complete the installation process.
GTnet Content
“Merit Link” and “GTnet” Buttons on
the Player Menu Screen
FIGURE 12 - GTNET BUTTON
GTnet content is available for a monthly
charge, billed to a credit card or PayPal account. Subscriptions are available through
the eCommerce site on the Gametime unit.
Features of GTnet:
1.One free, user selected game, per 3
month subscription.
2.Unlimited MegaWeb access
3.Hot Topics
4.Participation in TournaTime
NOTE: The GTnet buttons on the Player
Menu Screen and Main Menu Screen
will only appear if you have purchased
a subscription.
Touch the GTnet button on the Player Menu
Screen to choose a feature. More information about TournaTime setup and play can
be found in the TournaTime section of this
manual.
Setup
GTnet features can be enabled or modified
through the Options screen in the GTnet
Menu. The Hot Topics game settings are also
found in the GTnet Menu.
NOTE: The Hot Topics button will only
appear if Hot Topics is enabled in the
MegaWeb allows you to access the World
Wide Web through the game. Use the
touchscreen to navigate the Web.
Home Page
Once the game connects to the Internet, the
browser opens to http://www.yahoo.com,
the default Home Page. The screen has
standard navigation buttons (Forward, Back,
Stop, Home, Refresh) and a button that brings
up a keyboard for entering Web addresses
or search text.
NOTE: Text can be entered into a text
field after the field itself is touched and
activated.
NOTE: Java and Flash are not supported in MegaWeb. Pages containing Java or Flash cannot be loaded on
the game at this time.
E-mail and Attachments
E-mail can be accessed through Web-based
e-mail sites using the keyboard, but only image and text attachments can be opened.
Attachments cannot be saved to the machine.
To Enter This Screen, Touch “Hot
Topics” on the GTnet Menu
FIGURE 13 - HOT TOPICS GAME MENU
Hot Topics games allow players to compete
in games featuring regularly refreshed current events.
Setup
Games appearing as part of the Hot Topics
Menu are selectable via the Hot Topics button
in the GTnet Menu, which works in the same
manner as categories in the regular Game
Setup Menu.
Merit’s TournaTime is designed to network
Megatouch Gametime games over the
Internet for the purpose of playing in tournament games. All Tournament configuration
and maintenance is controlled by a central
server, which is managed by Merit’s Tournament Manager.
TM
To Enter This Screen, Touch the
“GTnet” Button on the Player Menu,
then “TournaTime.”
After Player Registration is Com-
plete, Use this Screen to Confirm or
Make Changes to Your Information.
FIGURE 14 - AVAILABLE TOURNAMENT
MATCHES
1.Touch the GTnet button on the Player
Menu Screen, followed by the
TournaTime button.
2.At the next screen, you can select a
game for play or view Rankings, read
Announcements, and review Tournament Rules.
3.Once a game is selected, you will enter
the registration screen. To register a
new player, touch the NEW PLAYER
button. At this screen, enter all the required information. For registered players, simply enter your name and PIN.
FIGURE 15 - PLAYER INFORMATION
SCREEN
NOTE: Registration information is required to determine Tournament winners. A player only needs to register
once to participate in any Tournament
available on the Tournament system.
4.Once the required fields have been
entered, confirm that all the information is correct. Touch the NEXT button
to view the TournaTime Disclaimer
Screen.
5.Touch the ACCEPT button to begin
play. Touch the DECLINE button to delete ALL entered information.
6.Once you log in, the TournaTime Player
Screen will appear. From this screen
you can view your top scores or enter
the ranking screens to compare your
scores to other players.
2.For unregistered users, the Merit Link
startup screen will transition to the
Registration Screen shown in Figure
16. Fill in the information fields using
the touchscreen keyboard enabled by
the icon at the top of the screen. When
finished, press Update Information.
NOTE: You can update your registration information whenever necessary.
Required fields are marked by an as-
terisk (*).
3.Once your information is accepted, you
can use the Order Options Screen
shown in Figure 17 to order a GTnet
subscription, purchase games, or redeem free games. Press Subscrip-tions and continue with the steps below to subscribe to GTnet. (To purchase games, follow steps 8-13; to redeem a free game, see steps 14-19.)
4.Review the GTnet subscription package and pricing details, then press
Continue if you agree with the terms.
5.The game will display the registration
information you previously entered.
Ensure that the information is correct,
then press Confirm Information.
6.You will be prompted to cancel the
transaction or subscribe. Press Sub-scribe Now to initiate your purchase
and advance to the Checkout Screen.
7.Choose between the PayPal or credit
card payment options displayed on the
Checkout Screen shown in Figure 18.
Follow the on-screen instructions to
complete your order.
8.On the Order Options Screen, select
Purchase Games.
9.Touch the Buy button next to each desired game to add the item(s) to your
Shopping Cart (see Figure 19). Touch
Remove to edit the contents of your
cart, then touch Checkout when fin-
Redeeming Free Games
14. On the Order Options Screen, select
Redeem Code.
15. Enter the coupon code you received
via e-mail in the space provided (touch
the space to activate the field), then
touch Redeem Coupon (see Figure
20).
ished.
FIGURE 19 - PURCHASE GAMES SCREEN
10. The game will display the registration
information you previously entered.
Ensure that the information is correct,
then touch Confirm Information.
11. Review the Shopping Cart items and
purchase price -- including any discounts earned for “bundled” game purchases -- then select PurchaseItems to advance to the Checkout
Screen. Otherwise, select Cancel
Transaction.
12. Choose between the PayPal or credit
card payment options displayed on the
Checkout Screen shown in Figure 18.
Follow the on-screen instructions to
complete your payment.
13. Once the transaction is approved, your
system will download the new game(s).
Touch the X in the upper right-hand
FIGURE 20 - REDEEM CODE SCREEN
16. Touch the Download button next to
your game choice to add it to your
Shopping Cart. Touch Remove to edit
your selection if desired, then touch
Checkout when finished.
17. Ensure that the registration information
displayed is correct, then touch Con-firm Information.
18. Complete your transaction by touching
the Download Game button. You may
also edit or abort the transaction by
selecting Remove From Cart or Can-cel Transaction.
19. After the new game download is complete, touch the X in the upper righthand corner of the screen, then confirm that you want to exit. When
prompted, turn off the game, wait 10
seconds and turn the game back on.
corner of the screen, then confirm that
you want to exit. When prompted, turn
off the game, wait 10 seconds and turn
the game back on.
Configures the CMOS settings on the motherboard to
Merit specificatio ns and c hecks the files o n the hard
drive.
A checksum test should be performed when the game is
locking up or rebooting. If the test fails, co ntact your
authorized dealer.
6Hardware
configura tion
•
Identifies system hardware and configures the
motherboard.
A hardware configuration occasionally needs to be
performed after a kit is installed a nd the touchscreen is not
responding to to uch or the calibration is off.
5 & 7Memory clear
for GTnet
•
Clears the log in name, password, and all settings.
•
Clears high scores and resets the software options.
A memory clear should be performed when a game is not
able to connect to the Internet and there is some questio n
about the accuracy of the connectivity information. After
performing a memory clear, Internet setup information must
be re-entered, and an
Update From Server
should be
performed.
NOTE: To urn aTim e games must per form an Updat e
From Server BEFORE performing a memory clear.
4 & 7Complete
memory clear
•
Clears A LL memory on hard drive including the
TournaTime player database,
TournaTime settings, high
scores, options, etc. It resets t he game to the factory
defaults. It also marks bad sectors on hard drive.
A complete memory clear should only be performed when
the game is locking up or resetting and it has passed the
checksum test. After performing a memory clear, the
player database should be reloaded, Internet setup
informatio n must be re-entered, and an
Update From
Server
should be performed.
NOTE:
TournaTime g ames must perf orm an Update
From Server BEFORE performing a complete memory
clear.
3Watchdog
Timer
•
When the watchdog timer is enabled, it will reboot the
machine within 2 minutes of a failure, allowing the game
to automatically reset itself if a problem arises.
DIP SWITCH SETTINGS
The following table provides information on the functionality of the hard DIP switches in
Megatouch Gametime games. Make sure to read the information in the Notes column to
determine what is affected when performing these functions. After performing any DIP
switch function, make sure to follow the instructions on the screen. The DIP switch
functionality is built into the software. Turn off the game. Press and hold the SETUP button
while turning on the game. The diagnostic page will be displayed. Touch the specific DIP
switch to activate it. Touch X to exit.
Check that the power cord is connected to a “live” outlet.
• Check that the power switch is on.
• Check that the power cord is connected to the game.
•
poor picture
quality
• Adjust Brightness, Contrast, Horizontal, and Vertical controls with
the monitor controls located on the Control Board board.
•
game locks up or
resets while
being played or
in the attract
mode
• no movement on
the screen
• power has to be
cycled off and on
to get th e game
to funct ion again
• Clean the vents and the fans of any dust and dirt that may interfere
with airflow.
• Perform a checksum test on the hard drive:
•
Turn off the game.
• Press and hold the SETUP button while turning on the game.
•
The diagnostic page will appear. Touch the option for DIP
switch 8. The test will take about 10 minutes.
•
A failure will cause the test to stop.
• A passed test will display “DRIVE CHECKSUM
COMPLETE RESET ALL DIP SWITCHES TO
REBOOT MACHINE”.
•
Clear memory with the following procedure:
• Turn off the game.
• Press and hold the Setup and Calibrate buttons.
• Turn the game on and keep holding the buttons until the
screen displays “TWO BUTTON CLEAR DETECTED
RELEASE BUTTONS”. This should take about 30 seconds.
•
Release the buttons. This will clear high scores, clear the
books and reset options, and reset the game menu and coin
menu to their factory settings.
•
"ERROR
READING DRIVE
C"
This message can be caused by the hard drive. Perform a
checksum test on the hard drive:
• Turn off the game.
•
Press and hold the SETUP button while turning on the game.
• The diagnostic page will appear. Touch the option for DIP
switch 8. The test will take about 10 minutes.
• A failure will cause the test to stop. When the hard drive fails
the test, the game will lock up with a "CHECKSUM ERROR"
message, which will stay on the screen until the power is
turned off. In this case, the hard drive will have to be
replaced. A passed test will display “DRIVE CHECKSUM
COMPLETE RESET ALL DIP SWITCHES TO REBOOT
MACHINE”.
Merit Entertainment
Troubleshooting Guide for Megatouch Gametime Games
Make sure that the Wireless USB Adapter is configured with
the same SSID, and WEP encryption as all network
components.
•
The
SSID
(Service Set Identifier) is an identification
name that wireless devices use to make connections.
In order for wireless devices to communicate, they must
all be set to the same channel and use the same SSID.
NOTE: This setting is only of concern if you have
changed the default SSID name during router installation.
See your router installation instructions for further details.
On-screen, all the
appropriate buttons
and connections are
present, but the
connection is
sporadic.
Interference with your wireless connection is most likely the
cause of this problem. Press the SETUP button to access the
Main Menu, then touch the
Tournatime
button, touch
Wireless
and then touch
Details
. On this screen, find the Link
Quality field. If the number is under 30, the signal strength is
weak. To alleviate this issue, try the following:
•
If your network goes through multiple floors, place the
wireless router on the upper floor.
•
Move the game closer to the router.
•
Keep it away from large metal objects such as filing
cabinets.
•
Try to keep the game and routers away from operating
microwave ovens and 2.4GHz cordless phones.
•
If you use 2.4 GHz phones and experience interference,
try using a different channel on the phone.
Merit Entertainment
Troubleshooting Guide for Megatouch Gametime Wireless Installation
Merit Industries, Inc. warrants its video machines to be free from defects in material
and workmanship for a period of one year
from the factory. The warranty covers all
electrical components (except fuses and
light bulbs) and printed circuit boards. The
touchscreen is under warranty for a period
of 3 years.
Failure due to misuse, vandalism, excessive
or intentional abuse, unauthorized service,
operation outside specified conditions (including, but not limited to, improper electrical
power source), fire, water damage, acts of
God, acts of war and civil unrest are specifically excluded.
Merit products are carefully inspected and
thoroughly tested prior to packing and shipment. Any damage discovered upon receipt
of goods, whether obvious or concealed,
must be reported immediately to the delivering carrier and claims made directly to them.
Merit assumes no responsibility for damages
once the product has left its facilities and
any disputes regarding transportation damage must be resolved with the shipping
company(s).
Merit will repair or replace, at its option, any
component, part or assembly that fails under warranty, provided that the game is returned, shipping charges prepaid, to Merit’s
repair facility and Merit is notified of the failure within the warranty period. Merit reserves the right to request the serial numbers of the game which has failed, and copies of sales invoices, bills of lading or other
documents as required to determine the validity of the warranty coverage. Merit will
return or replace warranty items, as specified above, shipping charges prepaid, by
ground transportation.
Merit’s obligation shall be limited to repair or
replacement as stated above, and shall specifically exclude any liability for consequential damages.
The above terms and conditions constitute
the sole obligation, written or implied, of Merit
Industries under its warranty coverage.
Merit Industries, Inc. (“Licensor”) is willing to license the enclosed software to you only if
you accept all of the terms in this license agreement (“Agreement”).
Ownership of the Software
1.The enclosed Merit® product, which may include but is not limited to the Megatouch®
software program (“Software”) and the accompanying written materials are owned
by Licensor and are protected by United States copyright laws, patent laws and
other intellectual property laws, by laws of other nations, and by international treaties.
Restrictions on Use and Transfer
2.If this Software package contains multiple media types (such as CD’s, flash cards,
hard drives, etc), then you may use only the type of media appropriate for your
Machine. You may not use the other media types on another Machine, or transfer, or
assign them to another user except as part of the permanent transfer of the Software
and all written materials (as provided for below in paragraph 4).
3.You may make one copy of the software for backup purposes only. You may not
copy or make backup copies of any software security key or software security
device under any circumstances.
4.You may permanently transfer the right to use the Software and accompanying
written materials (including the most recent update and all prior versions) if you retain
no copies and the transferee agrees in writing to be bound by the terms of this
Agreement. Such a transfer of this license to another party immediately terminates
your license. You may not otherwise transfer or assign the right to use the Software,
except as stated in this paragraph.
5.You may not operate or allow the operation of the Software at locations where the
operation of such Software does not comply with all local, state, and other
governmental body laws and regulations. You agree to not use or permit the use of
the Software in violation of any U.S. Federal, state, or local laws or regulations or
any foreign law or regulation, including laws regarding gaming, gambling or intellectual
property rights in or concerning the Software.
6.You may not modify, adapt, translate, reverse engineer, decompile, disassemble the
Software or create derivative works from the Software or any component thereof;
nor may you remove, modify or hide or otherwise make unreadable or non-viewable
any notice, legend, advice, watermark or other designation contained on the Software,
component thereof, or output therefrom.
7.You agree that the Software and the authorship, systems, ideas, inventions methods
of operation, documentation and other information contained therein, and all versions,
modifications and adaptations thereto are proprietary intellectual properties of Licensor
and are protected by civil and criminal law, and by copyright, trade secret, trademark
and the patent laws of the United States and other countries.
Limited Warranty
8.Licensor warrants, solely for your benefit, that the Software will function in material
conformity, with its accompanying documentation for a period outlined in Licensor’s
standard product warranty period after your receipt of the Software.
Licensor’s Obligations Under Warranty
9.Licensor’s sole obligation under the aforesaid warranty shall be to utilize commercially
reasonable efforts to correct or modify such portion of the Software as to make it
materially conform with the applicable documentation.
10. Licensor grants to you a limited, non-exclusive license to distribute and/or use one
copy of the Software on a single Merit (“Machine”) accompanied by a single licensor
factory authorized security key. Licensor reserves the right to update versions of the
software and the content to the Machine as deemed appropriate by the Licensor.
You are entrusted to maintain and protect your single licensor factory authorized
security key, password, or other identification from being utilized by any third party,
and you agree to be responsible for any use of the Software provided herein by a
third party utilizing your identification. Licensor maintains the right to immediately
terminate your License for reasons related to misuse or other non-conformity with
the rules expressed herein. While Licensor does not routinely inspect Machines,
Licensor also reserves the right to inspect or audit the Software from time to time in
Licensor’s sole discretion. To the extent that Licensor’s access to the Software
requires that Licensor also gain access to a Machine in which the Software is
installed, you agree to promptly provide Licensor, when requested, with permission
and aid in Licensor gaining access to the Machine.
Disclaimers
11. EXCEPT AS PROVIDED IN THE SECTION ENTITLED “LIMITED WARRANTY”, LICENSOR
MAKES NO OTHER PROMISES, REPRESENTATIONS OR WARRANTIES, WHETHER
EXPRESSED OR IMPLIED, REGARDING OR RELATING TO THE SOFTWARE OR
CONTENT THEREIN OR TO ANY OTHER MATERIAL FURNISHED OR PROVIDED TO
YOU PURSUANT TO THIS AGREEMENT OR OTHERWISE AND LICENSOR SPECIFICALLY
DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE WITH RESPECT TO SAID MATERIALS OR THE USE THEREOF.
TO THE MAXIMUM EXTENT ALLOWABLE BY LAW THE UNIFORM COMMERCIAL CODE
OR OTHER UNIFORM LAWS SHALL NOT APPLY TO THIS AGREEMENT.
Limitation on Liability
12. IN NO EVENT SHALL LICENSOR BE LIABLE UNDER ANY CLAIM, DEMAND OR ACTION
ARISING OUT OF OR RELATING TO THE SOFTWARE, ITS USE, INSTALLATION OR
LICENSOR’S PERFORMANCE OR LACK THEREOF UNDER THIS AGREEMENT FOR
ANY SPECIAL, INDIRECT, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES,
WHETHER OR NOT LICENSOR HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
CLAIM, DEMAND OR ACTION. IN ADDITION, WITHOUT LIMITING THE FOREGOING, IN
ALL EVENTS THE REMEDIES AVAILABLE TO YOU SHALL BE LIMITED TO THE AMOUNT
PAID BY YOU TO LICENSOR FOR THE SOFTWARE.
13. IN NO EVENT WILL LICENSOR BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY
LOSS OF PROFITS, LOST SAVINGS, OR OTHER INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF YOUR USE, MISUSE, BREACH OF THIS AGREEMENT OR
INABILITY TO USE THE SOFTWARE.
General
14. The validity and construction of this Agreement and of the rights and obligations herein
shall be determined and governed by the laws of the State of New York. By accepting
the terms of this Agreement, you acknowledge and accept that the courts of New
York, New York shall have exclusive jurisdiction and venue regarding any disputes
arising with regard to this Agreement or arising out of activity or misuse of the
Software.
15. Merit, in its sole discretion, may assign this agreement or any of its rights and
obligations hereunder.
16. If you have any questions concerning this Agreement or wish to contact Licensor for
any reason, please write: Merit Industries, Inc., 2525 State Road, Bensalem, PA
19020, USA.
Contrat de licence de logiciel de Merit Industries, Inc.
Merit Industries, Inc. (ci-après le "Concédant") est disposé à vous accorder la licence d'utilisation
du logiciel ci-inclus, à condition que vous vous engagiez à respecter tous les termes, clauses et
conditions du présent contrat de licence (Contrat).
Droit de Propriété
1.Le produit Merit ci-joint contenant, mais ne s'y limitant pas, le logiciel Megatouch™ (ci-après le
"logiciel") et toute la documentation écrite, restent la propriété du Concédant et sont protégés
par : les lois de droits d'auteur des Etats-Unis, les lois s'appliquant aux brevets déposés et à
la propriété intellectuelle, ainsi que par celles des autres pays et les traités internationaux.
Restriction d'Utilisation et Transfert
2.Si le présent logiciel comprend plusieurs types de composants (tels que CD-ROM, cartes
flash, disques durs, etc), vous ne pouvez utilisez que ceux qui conviennent à votre appareil.
Il est strictement interdit de les utiliser sur un autre appareil, les transférer -ou les céder à un
autre utilisateur, sauf en cas de transfert permanent du logiciel et de toute la documentation
écrite (comme indiqué ci-dessous au paragraphe 4).
3.Il est interdit de copier le logiciel, à l'exception d'une copie de sauvegarde. Il est aussi interdit
de reproduire -ou faire des copies de sauvegarde des programmes de clé de sécurité ou
autres fichiers de sécurité, quelles que soient les circonstances.
4.Vous pouvez céder en permanence à un tiers -le droit d'utiliser le LOGICIEL et toute la
documentation écrite l'accompagnant, (ainsi que la plus récente mise à jour et toutes autres
anciennes versions) seulement si vous n'en gardez aucune copie, et si le cessionnaire
s'engage, par écrit, à respecter les termes, clauses et conditions du présent Contrat. Cette
cession à un tiers met fin à votre licence immédiatement. Autrement, vous n'avez pas la
permission de transférer ou d'accorder à un tiers le droit d'utiliser le présent logiciel, excepté
que tel que décrit dans le présent paragraphe.
5.Il est interdit d'utiliser le présent logiciel ou de permettre son utilisation dans des emplacements
où l'utilisation du présent logiciel n'est pas conforme aux lois et réglementations locales,
nationales ou réglementations d'autres organismes gouvernementaux. Vous acceptez de ne
pas utiliser ou d'autoriser l'utilisation du logiciel d'une manière enfreignant les lois ou regulations s'appliquant à la propriété intellectuelle et au jeu, en vigueur aux Etats-Unis ou dans les
autres pays du monde, y compris les lois de l'ensemble du logiciel.
6.Il est interdit de modifier, adapter, traduire, démonter, décompiler, désassembler le logiciel ou
créer du matériel dérivé du logiciel ou de tout composant de celui-ci ; vous ne pouvez pas
enlever, modifier ou cacher ou rendre illisible ou non-visible toute instruction, légende, information ou filigrane ou autre désignation qui apparaît dans le logiciel, composant dudit logiciel
ou résultant dudit logiciel.
7.Vous convenez que le logiciel et les droits d'auteur, les systèmes, les idées, les inventions, les
méthodes d'utilisation, la documentation et autre information incluse, ainsi que toutes les
versions, modifications et adaptations qui s'y rattachent sont les propriétés intellectuelles du
Concédant et sont protégées par le droit civil et pénal et par le droit d'auteur, le secret
commercial, la marque déposée et le brevet aux Etats-Unis et dans les autres pays du monde.
Limite de Garantie
8.Le Concédant garantit seulement à votre intention, que le logiciel permettra une utilisation
conforme, avec la documentation l'accompagnant, pendant la période de temps indiquée
dans la période de garantie du produit standard du Concédant, à compter de la date de
livraison du logiciel.
Responsabilité du Concédant aux termes de la Garantie
9.La seule obligation du Concédant aux termes de la garantie susmentionnée sera de faire tous
les efforts commercialement raisonnables pour corriger ou modifier la partie du logiciel pour
le rendre matériellement conforme aux spécifications de la documentation.
10. Le Concédant vous accorde le droit d'utiliser une seule copie par appareil Merit (ci-après
"Appareil") accompagné d'une seule clé de sécurité autorisée en usine et fournie par le
Concédant. Le Concédant se réserve le droit de mise à jour des versions du logiciel et du
contenu de l'Appareil, quand il juge nécessaire de le faire. Il vous appartient également
d'empêcher que les mots de passe ou autres codes et la clé de sécurité soient utilisés par un
tiers. Vous acceptez d'assumer la responsabilité dans le cas de l'utilisation du logiciel par un
tiers. Le Concédant se réserve le droit de résilier votre contrat de licence à tout moment dans
l'éventualité d'une utilisation non-conforme aux clauses stipulées. Bien que le Concédant ne
contrôle pas les appareils périodiquement, il se réserve toutefois le droit de contrôler le logiciel
à tout moment et sans préavis de sa part. De surcroît, dans l'éventualité où le logiciel n'est
accessible qu'à travers la machine dans laquelle il est installé, le licencié s'engage à donner
libre accès au Concédant, ou ses représentants, à la machine et dans les plus brefs délais.
Exclusion de toute autre garantie
11. EXCEPTE COMME PREVU DANS LA SECTION INTITULEE "LIMITE DE GARANTIE", LE CONCEDANT
N'ASSURE AUCUNE AUTRE GARANTIE DE QUELQUE NATURE ET A QUELQUE TITRE QUE CE
SOIT, EXPLICITE OU IMPLICITE, EN RAPPORT AVEC LE LOGICIEL ET LES COMPOSANTS QUI
L'ACCOMPAGNENT OU, LE CAS ECHEANT, TOUT SUPPORT OU MATERIEL FOURNI
CONFORMEMENT AU PRESENT CONTRATEN PARTICULIER, LE CONCEDANT NE PEUT
DONNER AUCUNE GARANTIE, DE QUELQUE NATURE QUE CE SOIT, POUR LA
COMMERCIALISATION DE TOUS LES PRODUITS EN RAPPORT AVEC LE LOGICIEL OU AVEC
L'UTILISATION DE CELUI-CI. DANS LA MESURE OU CELA EST PERMIS PAR LA LOI, LE CODE
UNIFORME COMMERCIAL OU AUTRE LOI UNIFORME NE S'APPLIQUE PAS AU PRESENT
CONTRAT.
Limite de Responsabilité
12. LE CONCEDANT NE SERA EN AUCUN CAS RESPONSABLE DE TOUTE RECLAMATION,
DEMANDE OU ACTION RESULTANT DE OU EN RAPPORT AVEC LE LOGICIEL, SON UTILISATION
OU SON INSTALLATION, OU LA PERFORMANCE OU MANQUE DE PERFORMANCE DU
CONCEDANT EN VERTU DU PRESENT CONTRAT POUR TOUS DOMMAGES D'UNE NATURE
QUI N'EST PAS PRESUMEE PAR LA LOI ET QUI DOIVENT ETRE EXPRESSEMENT PROUVES,
DOMMAGE INDIRECTS, DOMMAGES-INTERETS POUR PREJUDICE MORAL, QUE LE
CONCEDANT AIT ETE AVISE OU NON DE LA POSSIBILITE D'UNE TELLE RECLAMATION,
DEMANDE OU ACTION. DE PLUS, SANS LIMITER CE QUI PRECEDE, LES DEDOMMAGEMENTS
A VOTRE DISPOSITION SERONT LIMITES AU MONTANT QUE VOUS AUREZ PAYE AU
CONCEDANT POUR LE LOGICIEL.
13. LE CONCEDANT NE SERA EN AUCUN CAS RESPONSIBLE : D'UNE RUPTURE DE CONTRAT,
DES DOMMAGES, Y COMPRIS TOUTE PERTE DE PROFIT, PERTES D'ECONOMIE OU TOUS
AUTRES DOMMAGES INDIRECTS OU DOMMAGES-INTERETS ACCESSOIRES DECOULANT
DE LA MAUVAISE UTILISATION OU DE L'IMPOSSIBILITE D'UTILISATION DU LOGICIEL.
Dispositions Générales
14. La validité et la construction du présent Contrat et les droits et obligations ci-inclus seront
déterminés et régis par les lois de l'état de New York aux États-Unis. En acceptant les
dispositions du présent contrat, vous acceptez également que tous litiges ou revendications
relatives seront réglés par voie d'arbitrage par un tribunal de l'état de New York, aux EtatsUnis.
15. Merit Industries se réserve le droit de transférer le présent Contrat à un tiers ainsi que ses
droits et obligations ci-après.
16. Pour toutes questions concernant le présent Contrat -ou si vous désirez contacter le Concédant
pour une raison quelconque, veuillez écrire à : Merit Industries, Inc., 2525 State Road, Bensalem,
Merit Industries, Inc. („Lizenzgeber”) ist nur dann bereit Ihnen eine Lizenz für die beiliegende
Software zu erteilen, wenn Sie alle Bestimmungen dieses Lizenzabkommens (“Abkommen”)
akzeptieren.
Eigentumsvorbehalt der Software
1.Das beiliegende Merit®-Produkt, welches das Megatouch® Softwareprogramm („Software”) beinhalten kann, aber nicht darauf beschränkt ist, und die schriftlichen Unterlagen
sind Eigentum des Lizenzgebers und sind durch die Gesetze der Vereinigten Staaten
und anderer Länder und durch internationale Verträge urheberrechtlich geschützt.
Beschränkungen im Gebrauch und Transfer
2.Sollte diese Softwarelieferung mehrere Medien enthalten (z.B. CD, Karten, Festplatten
usw.), dürfen Sie nur die für Ihre Maschine angebrachte Medienart verwenden. Die anderen
Medienarten dürfen nicht auf anderen Maschinen verwendet werden oder an Dritte
übergeben werden, abgesehen von einem endgültigen Transfer der Software und aller
schriftlichen Unterlagen (wie im untenstehenden Paragraphen 4 beschrieben).
3.Sie dürfen nur eine Sicherungskopie der Software herstellen. Unter keinen Umständen
dürfen Sie einen Softwaresicherungsschlüssel oder Sicherungsmaßnahmen kopieren oder
davon Sicherungskopien herstellen.
4.Sie dürfen das Nutzungsrecht für die Software und die schriftlichen Unterlagen (einschließlich
der aktuellen Version und aller vorhergehenden Versionen) an Dritte übertragen, wenn Sie
keine Kopie behalten und wenn der Empfänger die Bestimmungen dieses Abkommens in
schriftlicher Form akzeptiert. Bei einem solchen Transfer der Lizenz an Dritte erlischt Ihre
Lizenz umgehend. Abgesehen von den Bestimmungen dieses Paragraphen sind alle anderen
Transfers oder Übertragungen der Nutzungsrechte für diese Software unerlaubt.
5.Sie dürfen die Software nicht benutzen oder eine Nutzung gestatten, wenn eine
solche Nutzung der Software irgendwelche Gesetze und Verordnungen der
kommunalen oder staatlichen Behörden verletzen würde. Sie verpflichten sich die
Software nicht so zu nutzen oder nutzen zu lassen, dass sie damit gegen staatliche,
Bundes- oder Lokalgesetze oder Bestimmungen der USA oder gegen ausländische
Gesetze oder Bestimmungen, einschliesslich aller Gesetze bezüglich Glücksspiels,
Spielens oder geistigen Eigentumrechts der Software, verstossen.
6.Es ist Ihnen nicht gestattet, die Software abzuändern, zu verändern, zu übersetzen,
rückumzuwandeln, zu dekompilieren oder zu zerlegen, oder aus der Software oder eines
Teils davon andere Werke abzuleiten. Sie dürfen auch aus der Software, einem Bestandteil
der Software oder aus den Datenausgaben der Software keine Hinweise, Bemerkungen,
Ratschläge, Wasserzeichen oder andere Markierungen entfernen, verändern, verbergen
oder auf andere Art unlesbar machen.
7.Sie akzeptieren, dass die Software und die Urheberschaft, die Systeme, die Ideen,
Erfindungen, die Arbeitsweisen, die Dokumentation und alle anderen darin enthaltenen
Informationen und alle Versionen, Veränderungen, und Bearbeitungen davon das geistige
Eigentum des Lizenzgebers sind, und dass sie durch Straf- und Zivilgesetzgebung und
durch die Copyright-, Geschäftsgeheimnis-, Warenzeichen- und die Patentgesetze der
Vereinigten Staaten und anderer Länder geschützt sind.
Beschränkte Garantie
8.Der Lizenzgeber garantiert zu Ihren Gunsten, dass die Software für die angegebene
normale Garantiezeit des Lizenzgebers nach Ihrer Annahme der Software in erheblicher
Übereinstimmung mit der beiliegenden Dokumentation laufen wird.
Verpflichtung des Lizenzgebers im Rahmen der Garantie
9.Die ausschließliche Pflicht des Lizenzgebers im Rahmen der vorstehenden Garantie besteht
darin, alle geschäftlich vertretbaren Schritte zu unternehmen, um Teile der Software zu
berichtigen oder abzuändern, bis sie mit der beiliegenden Dokumentation erheblich
übereinstimmen.
10. Der Lizenzgeber gewährt Ihnen eine beschränkte, nicht-ausschliessbare Lizenz zur
Vertreibung und/oder Benutzung einer Kopie der Software auf einem einzelnen Merit™ („Gerät”)
mit einem einzelnen werksmäßig gestatteten Sicherungsschlüssel. Der Lizenzgeber behält
sich das Recht vor, nach eigenem Ermessen die Software und den Inhalt der Maschine zu
verbessern. Sie sind dafür verantwortlich ihren individuellen, vom Lizenzgeber werksmäßig
gestatteten Sicherheitsschlüssel, ihr Passwort oder anderweitigen Identifikationsmechanismus
instandzuhalten und abzusichern gegen die Nutzung durch eine dritte Partei, und sie akzeptieren
die Verantwortung für jegliche Nutzung der besagten Software durch eine dritte Partei mithilfe
ihresIdentifikationsmechanismus . Obwohl der Lizenzgeber nicht regelmässig Maschinen
inspiziert, behält sich der Lizenzgeber das Recht vor, ihre Lizenz umgehend zu kündigen aus
Gründen des Missbrauchs oder bei Nichtbefolgung der Bestimmungen in diesem Vertrag. Der
Lizenzgeber behält sich ebenfalls das Recht vor, die Software von Zeit zu Zeit nach eigenem
Ermessen zu inspizieren oder zu überprüfen. Im Falle, dass der Lizenzgeber Zugang zu dem
Gerät wünscht, in dem besagte Software installiert ist, erklären Sie sich bereit, dass sie dem
Lizenzgeber, wenn nötig, Erlaubnis und Hilfe beim Zugang zum Gerät verschaffen.
Beschränkungen
11. ABGESEHEN VON DEN BESTIMMUNGEN DES PARAGRAPHEN „BESCHRÄNKTE GARANTIE"
GIBT DER LIZENZGEBER KEINE SONSTIGEN VERSPRECHEN, VERPFLICHTUNGEN ODER
GARANTIEN, OB AUSDRÜCKLICH ODER STILLSCHWEIGEND, FÜR DIE SOFTWARE ODER
IHRE BESTANDTEILE ODER FÜR ALLE ANDEREN MATERIALIEN, DIE IHNEN IM RAHMEN DIESES
ABKOMMENS ZUR VERFÜGUNG GESTELLT ODER ÜBERLASSEN WERDEN, UND DER
LIZENZGEBER LEHNT AUSDRÜCKLICH ALLE ANSPRÜCHE AUF MARKTFÄHIGKEIT UND
EIGNUNG DER BESAGTEN MATERIALIEN FÜR DEN GEWÖHNLICHEN GEBRAUCH AB. SOWEIT
GESETZESMÄSSIG ZUGELASSEN, SOLLEN DIE HANDELSRECHTLICHE GESETZGEBUNG
AUS DEM UNIFORM COMMERCIAL CODE ODER ANDERE GESETZE AUF DIESES ABKOMMEN
NICHT ANWENDBAR SEIN.
Haftungsbeschränkung
12. DER LIZENZGEBER HAT KEINERLEI HAFTUNG BEI EINEM ANSPRUCH, EINER FORDERUNG
ODER EINER KLAGE, DIE AUF NUTZUNG DER SOFTWARE, DEREN INSTALLIERUNG, DER
LEISTUNG DES LIZENZGEBERS ODER DESSEN VERSAGEN IM RAHMEN DIESES ABKOMMENS
FÜR JEGLICHE FOLGE-, INDIREKTE, SONDER- ODER NEBENSCHÄDEN BERUHEN, SELBST
WENN DER LIZENZGEBER AUF DIE MÖGLICHKEIT EINES SOLCHEN ANSPRUCHES, EINER
FORDERUNG ODER EINER KLAGE HINGEWIESEN WURDE. WEITERHIN UND OHNE
BESCHRÄNKUNG DES LETZTEN SATZES, DÜRFEN IN ALLEN FÄLLEN DIE IHNEN ZUR
VERFÜGUNG STEHENDEN ABHILFEN DIE VON IHNEN FÜR DIE SOFTWARE AN DEN
LIZENZGEBER GEZAHLTE SUMME NICHT ÜBERSCHREITEN.
13 . DER LIZENZGEBER HAT IN KEINEM FALL EINE HAFTUNG IHNEN GEGENÜBER FÜR SCHÄDEN,
EINSCHLIESSLICH ETWAIGER GEWINNVERLUSTE, NICHT REALISIERTER EINSPARUNGEN
ODER ANDERER NEBEN- ODER FOLGESCHÄDEN, DIE AUS IHRER VERWENDUNG,
MISSBRAUCH, VERLETZUNG DIESES ABKOMMENS ODER GEBRAUCHSUNFÄHIGKEIT DER
SOFTWARE ENTSTEHEN.
Allgemein
14. Die Rechtsgültigkeit und Provisionen dieses Abkommens und der darin enthaltenen Rechte und
Pflichten werden durch die Gesetze des Staates von New York bestimmt. Sollten sie diese
Vereinbarungen annehmen, dann akzeptieren Sie, dass der ausschliessliche Erfüllungsort
und Gerichtsstand bei den Gerichten von New York im Staat New York liegen hinsichtlich aller
Streitigkeiten, die diesen Vertrag betreffen, oder die durch Leistung oder Missbrauch der
besagten Software entstehen.
15. Merit kann nach eigenem Ermessen dieses Abkommen oder jedes der darin enthaltenen
Rechte und Pflichten an Dritte abtreten.
16. Bei Rückfragen über dieses Abkommen oder wenn Sie den Lizenzgeber aus einem anderen
Grund kontaktieren wollen, bitte schreiben an: Merit Industries, Inc., 2525 State Road, Bensalem,
PA 19020, USA.
31 MEGATOUCH GAMETIME OWNER’S MANUAL PM0503-10
Please read the enclosed license agreement. Operation of this game
constitutes acceptance of the Merit Software License Agreement.
Veuillez lire le contrat de licence d’utilisation ci-inclus. Si vous utilisez ce
jeu, vous vous engagez à respecter les termes et conditions du contrat de
licence d’utilisation du logiciel de Merit.
Bitte beiliegendes Lizenzabkommen durchlesen. Das Merit Software
Lizenzabkommen tritt in Kraft, sobald dieses Spiel verwendet wird.
MEGATOUCH GAMETIME OWNER’S MANUAL
PM0503-10
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.