ABL eMH3WALLBOX TWIN WITH CHARGING SOCKETS TECHNISCHES DATENBLATT

TECHNICAL DATA SHEET

Data sheet version 3W2215E_c, current 11/2017, page 1

eMH3 WALLBOX
TWIN

WITH CHARGING SOCKETS

22 kW

Our new eMH3 wallbox impresses with an extremely
clean and elegant design. The color backlit symbols in
the mirror-finish black cover with silver frame indicate
the current charging status. This eMH3 Twin has two
Type 2 charging sockets with a charging capacity of up
to 22 kW. For access control, the internal RFID module
of the eMH3 Wallbox can be activated at any time via
software. Of course, the eMH3 comes with our DC fault
current detection installed as standard. In addition, a
GSM module is integrated and allows for accounting the
consumed charging current with a backend via the OCPP
protocol. The wallbox is prepared for use as a master. The
master-slave system is suitable for group solutions that
are billed via a back end system.

General information

Model eMH3

Part number 3W2215

EAN number 4011721171562

Commodity code 85371091

Packaging unit (PU) 1 unit

Packaging (dimensions HxWxD) 492 x 400 x 194 mm

Includes eMH3 Wallbox, printed Quick Start Guide, 1 three-square socket

wrench

Input/Supply

Power supply for supply cable sizes up to 5 x 10 mm²

Rated voltage 230 / 400 V

Rated current 32 A

Rated frequency 50 Hz

Back-up fuse 32 A (required onsite), C characteristic recommended

Terminal block Direct connection to RCCB

PE: 10 mm² feed-through terminal block

ABL SURSUM
Bayerische Elektrozubehör GmbH & Co. KG

Albert-Büttner-Straße 11
D-91207 Lauf / Pegnitz

Tel. [phone]
Fax [phone]

[e-mail]
www.abl.de

TECHNICAL DATA SHEET

Data sheet version 3W2215E_c, current 11/2017, page 2

Output/vehicle connection

Connection system Two lockable Type 2 charging sockets in acc. with IEC62196-2

Output voltage 230 / 400 V

Max. charging current 32 A

Maximum output 1 x 22 kW or 2 x 11 kW

Shut down (Standby) all contacts

Protection/integrated components

RCCB RCCB, Type A, 30 mA

DC fault current detection

Energy meter MID-approved (Ttotal/kWh, Tpart./kWh, P, U, I)

Installation contactor 4-pole (charging procedure activation)

electronic, I

Δn d.c.

≥ 6 mA

Charge control/status indicators

Charge controller EVCC

Communication in acc. with IEC 61851-1, Mode 3

Operating status indicator LED (stand-by, EV detected, charging)

Firmware indicator LED (flashes on startup)

Fault indicator LED (various flash patterns)

Interface RS485

RFID card reader integrated (disabled by default), support for MIFARE ULTRA-

Access control RFID (after activation via software tool)

Communication internal GSM module, OCPP 1.5

LIGHT transponder

Standards/Directives

IEC 61851-1 / 61439-7

Operating conditions

Storage temperature -30°C to 85°C

Operating temperature -30°C to 50°C

Relative humidity 5 to 95%, no condensation

Class of protection I

Overvoltage category III

Pollution degree 3

Degree of protection (housing) IP54

Power dissipation 0.5 W

ABL SURSUM
Bayerische Elektrozubehör GmbH & Co. KG

Albert-Büttner-Straße 11
D-91207 Lauf / Pegnitz

Tel. [phone]
Fax [phone]

[e-mail]
www.abl.de