ABB Xiamen H81313P2-A, H81363P2-A, H81364P1-A, H81313P2-A-02, H81363P2-A-02 Specification
...
Mini video outdoor station
labeling requirements for placement and operation of video
DANGER
Dangerous currents flow through the body when coming
into direct or indirect contact with live components. This
can result in electric shock, burns or even death. Work
improperly carried out on current-carrying parts can cause
fires.
– Disconnect the mains voltage prior to mounting and
dismantling!
– Permit work on the 100 – 240 V mains network to be
carried out only by specialist staff.
■
Please read the mounting instructions carefully and keep them for
future use.
■
Additional user information and information about planning is
available at http://new.abb.com/low-voltage/products/buildingautomation/product-range/abb-welcome or by scanning the QR
code.
English
Intended use
As a part of the ABB-Welcome IP system, this device can only be
used with accessories from the system.
Manufacturer
ABB Genway Xiamen Electrical Equipment CO., LTD.
Address: No.7 Fangshan South Road, Xiang An, Xiamen, Fujian,
China
Post Code: 361000
Technical data
Rating voltage 24 V
Operating voltage
range
Rating current
Operating temperature -40 °C…+55 °C
Product dimensions
Camera type CMOS
Camera viewing angle 104°
Resolution ratio 0.3 M (640 x 480 pixel), 25fps
Power supply for door
opener
Floating output for
door opener
Video codec H.264
Audio codec G.711
IP level IP 54
IK level IK 07
Network connection
standard
Video privacy
Making and saving video recordings can infringe on
personal rights! Always observe applicable legal and
components!
20-27 V
27 V , 310 mA
24 V , 350 mA
99 mm x 168 mm × 26 mm (H8131.P.-.)
105 mm x 180 mm × 43 mm (H8136.P.-.)
15 V , 4 A impulse, max. 250 mA
holding
250 V , 3 A
30 V , 3 A
IEEE802.3, 10/100 Mbps, auto MDI/MDI-X
Operation
Indicator flashes slowly: ringing
1
Indicator flashes quickly: busy line
Call indicator
2
Unlock indicator
3
Speaker and microphone integration
4
Round pushbutton
5
For the operation of this device we recommend the extended product
manual. (see QR code)
Connection
Door status detection interface
1
Exit button interface
2
Plug-in clamps (LOCK...AGND) for door opener
3
Plug-in clamps (COM...NC...NO) for floating output
4
Plug-in clamps (DC+...GND) for standalone power supply
5
LAN (PoE)
6
N/A
7
EU declaration of conformity
Hereby, ABB Genway, declares that this Mini outdoor station H8131
is in compliance with the essential requirements and other relevant
provisions of RE Directive 2014/53/EU. The complete of the EU
declaration of conformity is available by scanning the QR code.
FCC ID: 2AEBL-H8131
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Only operate the device in accordance with the instructions supplied.
Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to
operate the equipment.
This device complies with FCC radiation exposure limits set forth for
an uncontrolled environment. In order to avoid the possibility of
exceeding the FCC radio frequency exposure limits, human proximity
to the antenna shall not be less than 20cm (8 inches) during normal
operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Loading...