Technical Datasheet Catalogue Page
59 2.32"
63.3 2.49"
34 1.34"
55.8 2.19"
CE
CB
RoHS
1SNK 161 019 D0201 1SNK 161 019 S0201
ZS35 Screw Clamp Terminal Block
Feed-through
16 mm 0.630 in Spacing
3D CAD outline drawings available on "Control Product 3D" portal
Ordering Details Type Order Code EAN Code
Grey
Blue
Orange
ZS35 1SNK 516 010 R0000 3472595160105 20 53.40
ZS35-BL 1SNK 516 020 R0000 3472595160204 20 53.40
ZS35-OR 1SNK 516 030 R0000 3472595160303 20 53.40
Declarations and Certificates Document Part Number
UE Directive 1SND 225 081 C1006
Third Party Certificate 1SND 161 028 A0200
Features and Benefits
Closed terminal block:
- No end section needed,
- Optimized rigidity.
Pack
(ing)
Weight g (1 pce)
35 mm²
0 AWG
RoHS 1SND 230 491 F0203
Atex Declaration 1SND 225 085 C1003
1
General Information
2
The following information must be strictly adhered to in order to guarantee the terminal block electrical, mechanical and environmental performance.
Protection IP 20 NEMA 1
Rail
Wire stripping length
Operating tool
Torque
Mechanical endurance
of disconnect system
DIN3-TH35
17 mm 0.669 in
Screw clamp Screw rail contact
(Maximum value)
Flat screwdriver
6.5 mm 0.256 in
2.9 Nm 25.7 lb.in
± 0.1 Nm ± 0.885 lb.in ± 0.1 Nm ± 0.885 lb.in
Material Specifications
Insulating material Polyamide
IRC 600 V
Flammability UL94 V0
NF F 16 101 I2F2
Needle ame test IEC 60695-11-5 Compliant
Connecting capacity per clamp
1 Rigid conductor 6-35 mm² 10-0 AWG
1 Flexible conductor without ferrule 6-35 mm² 10-0 AWG
1 Flexible conductor with ferrule
Ferrule maximum outer diameter
14 mm 0.551 in
Multi Connecting capacity per clamp
2 Rigid conductors 16 mm² 4 AWG
2 Flexible conductors without ferrule 10 mm² 6 AWG
2 Flexible conductors with twin ferrule
Don't mix solid and flexible conductors in the same clamp
Don't mix solid or flexible conductors of different sizes in the same clamp
The "Connecting capacity with ferrule " data is guaranteed with ABB crimping tool PS-3
Cross section
Rated cross section 35 mm² 0 AWG
Maximum Cross section Manufacturer data 35 mm² Manufacturer data 0 AWG
Gauge A9-B9 / 10 mm / 0.394 in / IEC 60947-7-1
Electrical characteristics
Current
Rated current IEC 60947-7-1 125 A
Field and factory wiring Cat.2 UL 1059 150 A
Factory wiring Cat.1 UL 1059 150 A
CSA-C-22.2 n° 158 150 A
Rated short-time withstand current 1 s (Icw) 4200 A
Short-time withstand current 0.5 s Manufacturer data
5 s Manufacturer data
10 s Manufacturer data
30 s Manufacturer data
1 mn Manufacturer data
Rated short circuit withstand CSA-C-22.2 n° 158
Max. current (45° temperature increase) / Max. cross section (mm²) Manufacturer data 125 A 35 mm²
Maximum short circuit current (1s) Manufacturer data 4200 A
Short Circuit Current Rating (SCCR) SA UL 1059 supplement
ZS35 Terminal block
125.0A
117.9A
110.2A
102.1A
93.2A
83.3A
72.2A
58.9A
41.7A
0.0A
0
20
40
60
80
100
120
140
55 65 75 85 95 105115
AMBIANT TEMPERATURE (°C)
CURRENT (A)
3
SCCR UL 1059
With the following congurations:
Maximum voltage
Suitable conductor wire range
Fuse rating
Fuse designation
Fuse manufacturer name
Fuse type
Short circuit current
Voltage
Rated voltage IEC 60947-1 1000 V
Rated voltage UL 1059 600 V
Use Group UL 1059 C
Rated voltage CSA-C-22.2 n° 158 600 V
Rated voltage Ex e IEC/EN 60079-11 630 V
Rated impulse withstand voltage 8000 V
Dielectric test voltage 2200 V
Pollution degree IEC 60947-1 3
Overvoltage category IEC 60947-1 III
Dissipated power
Maximum dissipated power at rated current
IEC 4 W
Rated power dissipation at an ambient temperature of 23 °C - IEC 60947-7-3
Overload and short-circuit protection
Separate arrangement
Exclusive short-circuit protection
Separate arrangement
1 fuse and 4 feed-through blocks
Overload and short-circuit protection
Compound arrangement
Exclusive short-circuit protection
Compound arrangement
5 fuse blocks
Temperature range
Ambient temperature min/max Storage -55 +110 °C -67 +230 F
Installing -5 +40 °C -23 +104 F
Service IEC 60068-2-1 -55 +110 °C -67 +230 F
EN 60079-7 -55 +85 °C
Current Derating curve for continuous service temperature
Environmental Characteristics
4
Additional climatic tests
Dry heat IEC 60068-2-2 Compliant
Conditions Temperature +100 °C
Duration of test 96 h
Cyclic damp heat IEC 60068-2-30 Compliant
Conditions Temperature +55 °C
Number of cycles 2
Cold IEC 60068-2-1 Compliant
Conditions Temperature -40 °C
Duration of test 96 h
Z/ABDM climatic sequence IEC 60068-2-61 Compliant
Conditions Dry heat Duration of test / Temperature 16 h +85 °C
Cyclic damp heat Number of cycles / Temperature 1 +55 °C
Cold Duration of test / Temperature 2 h -25 °C
Corrosion
Salt mist IEC 60068-2-11 Compliant
Conditions Duration of test 96 h
Concentration 5 %
SO2 ISO 6988 Compliant
Conditions Duration of test 48 h
Concentration 0.2 dm³
Sulfur dioxide IEC 60068-2-42
Conditions Duration of test
Hydrogen sulfur IEC 60068-2-43
Conditions Duration of test
Flowing mixed gas corrosion test IEC 60068-2-60
Conditions Number of the test method
Duration of test
Vibrations
Vibrations IEC 60068-2-6 Compliant
Conditions Frequency range 10-55 Hz
Number of cycles 10
Amplitude
Acceleration 10 m/s²
Ramdom vibrations and climatic sequence IEC 60068-2-64
Conditions Duration of test
Frequency range
Acceleration
Climatic cycles
Step 1 -> Temperature / Duration of test
Step 2 -> Temperature / Duration of test
Temperature variation per minute
ZS35 Terminal Block Accessories Compatibility
5
Description Type Order Code
1
End Stops
Jumper Bars
2
Circuit Separators
3
Protecting Covers
4
Protecting Cover Kits
5
Terminal Block Markers
6
BAZH1 1SNK 900 102 R0000 20 23.90 1SNK 160 026 D0201
JB16-2 1SNK 916 302 R0000 10 10.20 1SNK 160 032 D0201
JB16-3 1SNK 916 303 R0000 10 16.00 1SNK 160 032 D0201
JB16-4 1SNK 916 304 R0000 10 21.80 1SNK 160 032 D0201
JB16-5 1SNK 916 305 R0000 10 27.60 1SNK 160 032 D0201
JB16-10 1SNK 916 310 R0000 10 56.60 1SNK 160 032 D0201
CS-R1 1SNK 900 103 R0000 20 5.20 1SNK 160 018 D0201
CO 1SNK 900 604 R0000 1 300.00 1SNK 160 020 D0201
PL16 1SNK 900 622 R0000 10 4.60 1SNK 160 021 D0201
KCO 1SNK 900 624 R0000 1 47,8 1SNK 160 028 D0201
MC812 1SNK 160 000 R0000 22 0.09 1SNK 160 009 D0201
UMH 1SNK 900 611 R0000 10 0.20 1SNK 160 001 D0201
PROCAP8 1SNK 900 613 R0000 20 1.00 1SNK 160 013 D0201
SAT8 1SNK 900 616 R0000 5 6.00 1SNK 160 013 D0201
(ing)
Pack
Weight Technical Datasheet
pieces g (1 pce) PDF
Loading...