ABB DY365 User guide

DIGITAL YEARLY TIME/ASTRONOMICAL
SWITCH

DY365

User Manual

Index

Q Technical features page 3
Q Safety warnings page 4
Q Dimensions page 4
Q Wiring diagrams page 5
Q Display and keyboard description page 6
Q Initial operation page 7
Q Start page (or main) page 8
Q Menu description page 11
Q Settings menu page 12

Language setting menu page 13
Date setting menu page 14
Time setting menu page 15
Daylight saving time (DST)/winter time (CET)
change setting menu page 16
Astronomical coordinates setting menu page 18
Random switchings setting menu page 20
Cycle switchings setting menu page 21
Protection PIN setting menu page 22

Q Manual operation menu page 23
Q Program menu page 26

Program menu: new page 31
Program menu: new daily timed page 32
Program menu: new weekly timed page 33
Program menu: new yearly timed (or monthly) page 34
Program menu: new holiday timed page 36

User manual DY365

Program menu: new astro night page 38
Program menu: new astro daily page 42
Program menu: new astro weekly page 43
Program menu: new astro yearly (or monthly) page 44
Program menu: new astro holiday page 46
Program menu: check page 48
Program menu: modify page 50
Program menu: copy page 52
Program menu: delete page 53

Q Bluetooth page 54
Q Bus menu page 56

Simple network configuration (one DY365,

one or more remote actuators) page 58
Complex network configuration (several
DY365, one or more remote actuators) page 58
Connection test page 59
Programs copy on the bus page 60
Reception programs on the bus page 61

Q SYNC menu page 62
Q Hour couter menu page 64
Q Reset menu page 66
Q Firmware menu page 68
Q Error signals page 69
Q Battery management page 70
Q Reference standards page 70

- 1 -

English

USER MANUAL

DY365 is an electronic digital time switch for the management over time of the electrical devices. It allows time programming (periodicity: daily,
weekly or annual) or astronomical programming. DY365 has two on-board relays but it’s able to control up to eight different channels (relay); the
other six channels are realized by remote actuators available as accessories: DY365 4CE (4 relays) or DY365 2CE (2 relays), connected to the DY365
via BUS. Each channel can be associated with a different programming (time or astronomical). DY365 also offers the possibility to connect via BUS a
GPS module, DY GPS (available as an accessory), that captures the time and the position through the satellite system, ensuring high accuracy over
time or DY DCF77 (available as an accessory), that captures the time ensuring high accuracy over time. The backup battery keeps the settings even
in case of power failure and can be replaced through the cover (sealable). DY365 time switch has a Bluetooth interface that allows it to be coupled
with mobile devices (smartphone or tablet). Thanks to the free app that can be downloaded from the AppStore and Google Play stores, it is possible
to program and make settings directly on your smartphone, and then transfer all the data to the time switch.

English

Code Model Description
2CSM221201R1000 DY365 Astronomical time switch with bus for connecting GPS modules and remote actuators
2CSM250411R1000 DY GPS GPS module for receiving time and position from satellites
2CSM250421R1000 DY DCF77 Time module for receiving time
2CSM221181R1000 DY365 4CE Remote actuator module with 4 auxiliary relays of 8A / 250V
2CSM221191R1000 DY365 2CE Remote actuator module with 2 auxiliary relays of 8A / 250V

DY GPS / DY DCF77 DY365 4CE DY365 2CEDY365

- 2 -

User manual DY365

TECHNICAL FEATURES

• Power supply: 230 Vac (-15% ÷ +10%) 50/60 Hz

• Power consumption: 7 VA (2.6W)

• Lithium backup battery: 3V, CR14250 type (replaceable)

• 8 available channels*

• Terminals for:

- device power supply (terminals 1-2)

- auxiliary power supply output of 12V dc ±10%, 80mA,
1W (compatible with DY GPS or DY DCF77 power supply)
(terminals 6-7)

- communication bus for the connection of DY365 4CE,

DY365 2CE, DY GPS or DY DCF77 additional modules
(terminals 8-9)

- monostable change-over relay 1 with maximum switchable
load of 16A / 250V (terminals 10-11-12)

- monostable change-over relay 2 with maximum switchable
load of 16A / 250V (terminals 16-17-18)

• Terminal block for cables with maximum cables section

• Display LCD with backlight (active with AC power supply)

of 2.5 mm

2

• Storable programs: 450 (900 events) (divisible on 8 channels)

• Actions type: 1B

• Bluetooth BLE 4.2 communication interface (active with mains
power supply)

• Operating frequency band: 2400-2483.5 MHz

• Maximum transmitted radiofrequency power: 4 dBm

• Operating temperature: -20 ÷ +50 °C

• Operating humidity: 20 ÷ 90% non condensing

• Storage temperature: -25 ÷ +70 °C

• Container: 4 DIN modules

• Protection degree: IP20

• Insulation: reinforced between accessible parts (front) and all

* The 8 channels are realized physically by as many relays.
The channels 1 and 2 are realized by the relays mounted on the
DY365; the other 6 channels are realized through the connection
via bus of DY365 4CE / DY365 2CE additional modules.

- 3 -

User manual DY365

English

the other terminals

SAFETY WARNINGS

 During product installation and operation it is necessary to

observe the following instructions:

1) The instrument must be installed by a qualified person,

strictly in observance of the connection diagrams shown in
this manual.

2) After installation inaccessibility to the terminals without

using dedicated tools must be guaranteed.

3) Before accessing the connection terminals, make sure that

the leads are not live.

4) Do not connect or feed the instrument if any part of it is

English

damaged.

5) The product must be installed and activated in compliance

with current electric systems standards.

6) Do not use the instrument for anything other than the

indicated purpose.

7) I n the electrical system upstream of the instrument must be

installed a protection device against the overcurrents

8) The product can be used in environments with Measurement

Category III and Pollution degree 2, according to the
Standard IEC 60730-1

9) The access to the device must be limited and the default

device PIN and Bluetooth password must be changed in
order to avoid tempering of programs of relays.

- 4 -

User manual DY365

DIMENSIONS (mm)

72

65

60

88

45

WIRING DIAGRAMS

extension

I/O

port

Connection of devices on the bus

I/O extension port

89

DY365 DY365 4CE DY GPS / DY DCF77

DY GPS / DY DCF77

DY GPS and DY DCF77 must be powered by a DC voltage at 12V.
This power supply can be obtained from terminals 6-7 of DY365
(see figure).

Note: for details of the connections of the additional modules see
the instructions supplied with the products.

- 5 -

User manual DY365

-

+

8

6

9

7

DY365 DY GPS / DY DCF77

-

+

English

DISPLAY AND KEYBOARD DESCRIPTION

 General indications
 Time indication

English

 Channel 1/channel 2 status indication

: active manual program

+ : blocked switchings
+ : active random switchings

+ (flashing) : active cycle switchings
: active holiday program
: active pulse program

 Channels status indication (CHANNEL) / days of the week (DAY)

configured channel (in off status)

configured channel (in on status)
failed configured channel (no communication)

ུTurn on the display

Access the menu
ESC (one level back)

 “

“
lock channel 2

ྲྀ Confirm selection
ཷ Hardware reset

- 6 -

User manual DY365

”: decrease datum/previous menu/ switching channel 1/

lock channel 1

”: increase datum/next menu/ switching channel 2/

INITIAL OPERATION

• Once out of the package, DY365 is off: press the key and
wait a moment before activating the display

• The set language is English. To change it, press the key
at least 3 seconds. Choose among: German, English, Spanish,

French, Italian, Russian and confirm with

• Make connections following the diagrams on page 5 of this

.

for

manual

• Power DY365: the backlight turns on permanently. Power
possible additional connected modules (DY365 4CE, DY GPS...)

• The presence of the backup battery allows the DY365 to have
updated date and time.
To make the other settings follow the following steps:

Date - format: DD/MM/YY

st

day of the week: Monday

- 1

Astronomical coordinates - country: France

- city: Paris

- latitude: North (48° 51’ 36”)

- longitude: East (2° 21’ 00”)

User manual DY365

Daylight Saving time (DST)
change: active

- start of daylight saving time (DST):
last Sunday of March at 02:00
o’clock

- end of daylight saving time (DST):
last Sunday of October at 03:00
o’clock

Time correction: - sunrise: +0:00

- sunset: +0:00

Time zone: +1:00 UTC

Random switchings: - minimum: 1 minute

- maximum: 5 minutes

Cycle switchings: - ON duration: 1 minute

- OFF duration: 1 minute

PIN protection: disabled (---)

Bluetooth: disabled (Password: 000000)

GPS module: active

- 7 -

English

START PAGE (or main)

information messages
date
relay 2 status
hour

channels status*

relay 1 status

Information messages

- day of the week

English

- GPS status (if enabled)

- battery status (only if discharged)

-

* See page 6. In this case there isn’t any configured channel

(no number turned on)

** Only if DY365 is not powered by mains.

In this condition the backlight is not active and the relay is in
off status.

**

• Press the key:

sunrise and sunset times***

*** The displayed times take into account possible entered values

NOTE: The device is supplied with deactivated Bluetooth
interface. To activate it, access Bluetooth menu (see page 54).

- 8 -

User manual DY365

to access the menu of the instrument
and to scroll through the messages of DY365
to display the Bluetooth signal level or the calculated

of correction (see page 16)
if the display shows
time is after the sunset time if the display show
means that the calculated sunrise time is before 00:00 or that
the calculated sunset is at 23:59

means that the calculated sunrise

Access the store of your device, install and start the free app DBT TIMER

08:53

DBT Timer

ALL

DWA 1

DWA 2

click here

to connect

29%

D

DW1

DW2

09:55

Back

NEARBY DEVICES

DY365 -7F54DEA5

FA:0D:78:95:14:C6

09:55

Back

NEARBY DEVICES

Unknow device

Bluetooth pairing request

26%

Enter PIN to pair with DY365 - 7F54DEA5 (Try
0000 or 1234).

PIN

Cancel

26%

09:56

26%

DBT Timer

ALL

DWA 1

DWA 2

DY365 -7F54DEA5

DY365

Update 25 seconds ago

OK

D

DW1

DW2

09:56

Back

Dy365 -7f54dea5

Update 33 seconds ago

DY365

Programs

Settings

Parameters

Advanced

settings

26%

English

Add Timer

- 9 -

User manual DY365

DWTL1

Synchronize

Activate Bluetooth on DY365 device (see page 54).

At the start the app displays the list of the associated DY365 devices. To associate a new device, press the symbol “ ” in the upper

right corner.

All the Bluetooth devices detected nearby are displayed: select the device to be associated from the list.
Note: each device is identified by the product code (for example DY365) and by the serial number (for example 00000020).
These informations can be viewed from the main page of the DY365
Warning: make sure that the DY365 is mains powered, Bluetooth interface is activated and that the display shows the main page (initial).
Otherwise the Bluetooth interface is not active and the device is not visible

Enter the password to associate the DY365 with your device

English

After successfully completing the procedure, the DY365 is added in the list of the associated devices.
Select the DY365 on which you want to act from the list of the associated devices
Note: communication between the app and the DY365 is point-to-point. This means that,
even in the presence of multiple DY365, the app can communicate with one only at a time.
The DY365 currently connected to the app displays the symbol * immediately after the serial number

The app displays the initial page of the selected DY365. From this page you can:
a. Create new programs that will then be copied to the DY365
b. Change the settings of the DY365
c. View the parameters and associate an alias to the DY365
d. Manually control the relay output/s and activate the random switching function or cycle function.

- 10 -

User manual DY365

MENU DESCRIPTION

 “Settings” menu allows you to change: language, date, time, daylight saving time (DST),

astronomical coordinates, minimum and maximum duration of the interval between

two switchings with random program, PIN for keyboard lock.

 “Bluetooth” menu allows

 “Bus” menu allows you to configure

additional relay modules and to transfer
programs among DY365.

 “Sync” menu allows the configuration of DY GPS or DY DCF77 module.
 “Hour counter” menu allows you to check the operation hours

(relay on) of the loads connected to each channel (relay).

 “Reset” menu allows you to reset settings, programmed settings, operating hour counter.
 “Ver FW” menu allows you to check the firmware version installed on the device.

 “Manual” menu allows you to switch or to lock the status of any

channel and to activate the function of random or cycle switchings.

- 11 -

User manual DY365

 “Programming” menu allows you to set a new

program or to check, to copy, to modify or to
delete a set program.

you to configure the Bluetooth
communication interface.

English

SETTINGS MENU

“Settings” menu allows you to view and eventually to modify the
the general operation settings of DY365, such as:

 language
 date
 time
 automatic daylight saving time (DST) change
 position (astronomical coordinates)
 interval duration between two random switchings
 ON and OFF time duration for cycle switchings
 keys protection by PIN

English

- 12 -

User manual DY365

Language setting menu

Available languages:
German, English, Spanish, French, Italian, Russian.

Quick access: from the main page it’s possible to access the
language setting by pressing the key

for at least 3 seconds.

- 13 -

User manual DY365

English

Date setting menu

1

Parameters

modification

2

English

Parameters modification

1

Possible date formats: day-month-year ( ), year-month-day ( ),

month-day-year (

2

Choose, by convention, the first day of the week. In Italy, for example, the first day of the week

is Monday, in the UK it’s Sunday.

3

Enter the date: day, month, year.

).

If DY GPS is connected and active, DY365 synchronizes date, time and coordinates (longitude, latitude) thanks to the received GPS signal.
If DY DCF77 is connected and active, DY365 synchronizes date and time only.
Synchronization occurs automatically every 30 minutes and is indicated by flashing the field "Time" (2 times).
The data received from DY GPS / DY DCF77 overwrite possible changes made manually.

- 14 -

User manual DY365

3

Time setting menu

1

Parameters
modification

Parameters modification

1

Set the time: hours, minutes.

2

Set the time zone*. Range: -14:00 ÷ +14:00 (at 15 minutes steps).

For Italy set +1:00.

* The time zone must be set manuallly also with connected DY GPS module.

If DY GPS is connected and active, DY365 synchronizes date, time and coordinates (longitude, latitude) thanks to the received GPS signal.
If DY DCF77 is connected and active, DY365 synchronizes date and time only.
Synchronization occurs automatically every 30 minutes and is indicated by flashing the field "Time" (2 times).
The data received from DY GPS / DY DCF77 overwrite possible changes made manually.

- 15 -

User manual DY365

English

Daylight saving time (DST)/winter time (CET) change setting menu

Daylight saving time (DST)/winter time(CET) change and vice versa can occur in an automatic way. In this case, DY365:

- increases by an hour in the passage from winter time (CET) to daylight saving time (DST)

- decreases by an hour in the passage from daylight saving time (DST) to winter time (CET)

For every change it’s necessary to specify:

English

the week of the month during

which the time change occurs

the day of the week

(Monday: 1, Tuesday: 2, ...)

(first, second, third, fourth, last)

In Italy,for example, daylight saving time (DST) begins occurs the last (
last (

) Sunday (

) of October ( ) at o’clock.

User manual DY365

- 16 -

the month the hour

) Sunday (

) of March ( ) at o’clock, and ends the

Parameters modification

1

Choose to activate ( ) or to disable ( ) the automatic time change.

2

Set date and time of the winter time (CET)-daylight saving time (DST) change.

3

Set date and time of the daylight saving time (DST)-winter time (CET) change.

- 17 -

User manual DY365

2

Parameters
modification

English

Astronomical coordinates setting menu

The setting of the geographical coordinates of the installation place allows DY365 to calculate, for each day of the year, sunrise and sunset
times.
To simplify the procedure, in the DY365 are stored the coordinates of the locations listed below; if your location is among them you can select
it from the menu

Note: the display on point

, otherwise it’s necessary to enter the coordinates of latitude and longitude (menu ).

shows “---------” if the coordinates have been entered manually or captured via DY GPS.

Location stored in DY365: Major cities of France, Germany, Italy, Russia, Spain, United Kingdom
and some other major cities in the rest of the world

The correction of sunrise and sunset times is useful for applications that require the turning on of lights in particular localities. It’s possible, in

English

fact, that the presence of disturbing elements, such as the mountains, can influence actual times of sunrise and sunset, making it necessary
to advance or delay of a few minutes the calculated times.

The twilight is the time interval before sunrise, or after sunset, characterized by the permanence of the light due to the spread by the atmo­sphere of the Sun light. During these time intervals it’s possible to distinguish clearly objects and conduct outdoor activities without using
additional lighting. Therefore, in some applications it is more interesting to take as times of switching on and off the twilight (civil) in place
of sunrise and sunset. With DY365 it’s possible to choose to turn on/off the loads depending on the times of sunrise and sunset or the civil
twilight. The calculated time correction also applies to the times of twilight. To view the calculated switching on time (sunset) and switching
off time (sunrise), from the main page press the key ok (see page 8).

- 18 -

User manual DY365

Parameters modification

Choose the installation location. If it’s not present, proceed with steps and .

Set the latitude of installation place.

Set the longitude of installation location.

Set a possible correction of the calculated sunrise time. Positive values to delay, negative values
to anticipate.

Set a possible correction of the calculated sunset time. Positive values to delay, negative values
to anticipate.

Choose as switching times the civil twilight ( ) in place of sunrise and sunset

(

) times.

If DY GPS is connected and active, DY365 synchronizes date, time and coordinates (longitude, latitude)
thanks to the received GPS signal. If DY DCF77 is connected and active, DY365 synchronizes date and
time only. Synchronization occurs automatically every 30 minutes and is indicated by flashing the field
"Time" (2 times). The data received from DY GPS / DY DCF77 overwrite possible changes made manually.

- 19 -

User manual DY365

2

Parameters
modification

English

Random switchings setting menu

1

2

English

The “random switching ” function (manual menu ´ random manual) allows you to automatically switch and at random time intervals any
channel among the 8 available.
In this menu it’s possible to define the minimum and maximum duration of the time interval between two random switchings. Default mini­mum duration is 1 minute, maximum duration is 5 minutes.

Parameters modification

1

Set the minimum duration. It’s possible to set values between 1 minute and the maximum duration.

2

Set the maximum duration. It’s possible to set values between the minimum duration and 23:59.
Note: setting the minimum duration equal to the maximum, the switchings will occur at fixed time intervals.

- 20 -

User manual DY365

Parameters

modification

Cycle switchings setting menu

The “cycle switching” function (manual menù ´ cycle manual) is a succession of on and off switching.
The cycle programme always starts from the on status. In this menu it’s possible to define the duration of on and off.
The duration of the on and off duration cannot be less than one minute.
Default on duration: 1minute, OFF duration: 1 minute

Parameters modification

1

Set the ON duration. It’s possible to set values between 1 minute and 99:59 hours.

2

Set the OFF duration. It’s possible to set values between 1 minute and 99:59 hours.

- 21 -

User manual DY365

ON

OFF

1

Parameters

modification

2

English

Protection PIN setting menu

English

The protection code (PIN) is used to lock the keyboard and prevent changes by unauthorized persons. With active PIN protection, pressing
any key, it’s necessary to enter the PIN: if PIN is correct the keyboard unlocks; after 3 minutes without pressing a key, the keyboard will lock
automatically.

To activate PIN protection:

- set a value between 000 and 999

To disable PIN protection:

- set “---” (located before 000 or after 999)

Note: If you have forgotten your PIN code to unlock DY365 it’s necessary to carry out a hardware reset (see page 66).

- 22 -

User manual DY365

MANUAL OPERATION MENU

“Manual” menu allows you to manually take action on the channels of DY365 and to check their status (on, off, or “------” if the channel
is not configured).

Possible operations:

program: the selected channel follows the set programming

temporary on : the selected channel is set on until the next programmed off event

temporary off : the selected channel is set off until the next programmed on event

permanent on : the selected channel is locked in on position until the manual unlocking (to unlock, access this menu and set a

different operation)

permanent off : the selected channel is locked in off position until the manual unlocking (to unlock, access this menu and set a

different operation)

random : the selected channel is set on and then will take place switching on / off at random intervals (the minimum and maximum

interval can be set from “Settings ´ random” menu)
ྲྀ cycle: the selected channel is set on and then will take place switching on / off (the ON and OFF duration can be set from
“Settings ´ cycle” menu)

- 23 -

User manual DY365

English

English

Channel status

- “-----” not configured channel

- on (off): on (off) channel after a programmed event

- on (off) +

- on (off) +

- on (off) +

- on (off) +

: on (off) channel after manual setting
: on (off) channel with blocked switching
: on (off) channel after random event

(flashing): active cycle switchings

Channel

status

- 24 -

User manual DY365

Shortcut keys

For channel aboard the DY365 (channel 1-2) it’s possible to set the operations described on pag. 21 through a combination of keys:

- temporary on/off:
press the key

- permanent on/off:
press for a long time (for 3 seconds at least) the key

(press again for a long time the key

- random:
press contemporary and for a long time (for 3 seconds at least) the key
Press again simultaneously and for a long time the keys

- cycle:
press contemporary and for a long time (for 3 seconds at least) the keys
Press again simultaneously and for a long time the keys

for channel 1 or for channel 2. If on becomes off and vice versa.

or

for channel 1 or for channel 2. The current state is locked until the unlocking

).

and

for channel 1 or for channel 2.

and or to disable the function.

and or to disable the function.

- 25 -

User manual DY365

and for channel 1 or

for channel 2.

English

PROGRAM MENU

The menu “program” allows you to:

create a new program
check created programs
change or delete a created program
copy all created programs on a channel in another channel
delete all programs of a channel

English

- 26 -

User manual DY365

Channels selection

scroll through the channels from 1 to 8:

- by pressing the key

- by pressing the key

to move to the next channel without selecting the current channel
to select/deselect the current channel and move to the next

Select days

scroll through the days of the week from 1 to 7:

- by pressing the key

- by pressing the key

to move to the next day without selecting the current day
to select/deselect the current day and move to the next

- 27 -

User manual DY365

English

Programs types

• Program ON/OFF: it is composed of a switching of the ON relay and of a subsequent switching of the OFF relay. It can have a daily period
(everyday with the same modes), weekly (every week with the same modes), annual (every year with the same modes)*.

• PULSE ON Program: is an ON relay switching for a maximum duration of 59 seconds. It can have a daily period (everyday with the same
modes), weekly (every week with the same modes), annual (every year with the same modes)*.

• PULSE OFF program: is a relay switching OFF for a maximum duration of 59 seconds. It can have daily period (everyday with the same
modes), weekly (every week with the same modes), annual (every year with the same modes)*.

• HOLIDAY program: is a period of time defined by a start time and an end time within which all programmed switchings (of that channel)
are disabled. The relay is in OFF position (OFF holiday) or in ON position (ON holiday).

* In the annual program, it’s possible to specify the month. In this case, the period is monthly (every month with the same modes). It’s also

possible to specify a definite date (the program carried out only once).

English

Channel types

• TIME channel: carries out programs of time type: ON / OFF, ON pulse, OFF pulse, holiday

• ASTRO channel: carries out programs of astronomical type, i.e. in the interval delimited by sunrise and sunset**: ON/OFF, ON pulse, OFF
pulse, holiday, night programs (see pages 36-37). ON switchings set before sunset are carried out at sunset, OFF switchings set after sunrise
are carried out at sunrise (except for some night programs that can have switching on or switching off during the day. See on page 36).

** times of sunrise and sunset are automatically calculated by DY365 according to geographic coordinates set during installation. In place of

sunrise and sunset times it’s possible to use the times of civil twilight (see page 18).

- 28 -

User manual DY365

 Important: on the same channel can’t coexist ON pulses and OFF pulses (if an ON pulse is already present, it’s not possible to save a

holiday OFF program and vice versa).

 Important: on the same channel can’t coexist holiday ON programs and holiday OFF programs (if a holiday ON program is already

present, it’s not possible to save a holiday OFF program and vice versa).

 Important: a channel may be either of clockwise or of astronomical type, but it can’t be of both types simultaneously. It’s not possible

to save programs of astronomical type on a channel where are stored programs of time type (and vice versa). Messages of

(astro program on channel astro) and (time program on astro channel).

In this case to proceed it’s necessary to delete the saved programs on that channel (see page 53).

Programs priority

The priority programs defines how DY365 manages the case in which programs with different period are running at the same time
(1 indicates higher priority).

Program

Date* Annual Monthly Weekly Daily
Holiday 1
Night 2
Pulse 3
On/Off 45678

* Date: select day, month, year (program carried “only once in the life of the product”). If the month is not specified, the program is carried

out all days xx of all months of the specified year.

- 29 -

User manual DY365

English

Priority list on/off

In case in which, on the same channel, on/off programs are provi­ded with different period (daily, weekly, ...) to carry out in the same
day, only the program with the highest priority is executed.

Daily program

Weekly program

English

of Monday begins and ends before the beginning of the weekly
program). Instead, the daily program of Sunday is carried out
because it’s the only one running for that day.

Holiday program

The holiday program just begins and ends exactly at the specified
times.

Daily program

Carried out program

From this example it’s possible to see that the daily event on
Monday is not carried out because in the same day it is provided
the beginning of the week program (even if the daily program

- 30 -

User manual DY365

Weekly program

Carried out program

Program menu: new

Choose the channels to program*

* See “Channels selection” on page 27

- 31 -

User manual DY365

Choose the

channel

English

Program menu: new daily timed

English

Program parameters

- on/off: on time and off time

- on pulse: time and pulse duration (max 59 seconds)

- off pulse: time and pulse duration (max 59 seconds)

- 32 -

User manual DY365

Enter

program

parameters

Program menu: new weekly timed

Program parameters

- on/off: day (or days)* and on time, day (or days) and off time

- on pulse: day (or days)* and pulse time, pulse duration (max 59 seconds)

- off pulse: day (or days)* and pulse time, pulse duration (max 59 seconds)

* See “Days selection” on page 27

- 33 -

User manual DY365

Enter

program

parameters

English

Program menu: new yearly timed (or monthly)

English

Program parameters

- on/off: day (or days) and on time, day (or days) and off time

- on pulse: day (or days) and pulse time, pulse duration (max 59 seconds)

- off pulse: day (or days) and pulse time, pulse duration (max 59 seconds)

- 34 -

User manual DY365

Enter

program

parameters

How to choose the day (or days) in an annual program (or monthly)

to set the program:

in the first, second, third, fourth or last week of the month
in / the day/s (Monday, ...) of the week just specified
the specified month (
the given year (

for all months)

for all years)

Note: the on event must correspond to the off in the same day. For

example, if the program includes two events on Monday and
on Wednesday, then there will be two off events on Monday
and on Wednesday. Otherwise

is signaled.

User manual DY365

- 35 -

to set the program on the last day:

of all months of all years
of the specified VV month of all years
of all months of the specified ZZ year
of the specified VV month of the specified ZZ year

to set the program on the day XX (1,2,3...):

of all months of all years
of the specified VV month of all years
of all months of the specified ZZ year
of the specified VV month of the specified ZZ year

English

Program menu: new holiday timed

English

HOLIDAY OFF: the relay is OFF from the

beginning to the end of Holiday program

HOLIDAY ON: the relay is ON from the

beginning to the end of Holiday program

Program parameters

- beginning of the program

- end of the program

- 36 -

User manual DY365

Enter

program

parameters

How to choose the day (or days) in a holiday program

to set the program:

in the first, second, third, fourth or last week of the month
in / the day/s (Monday, ...) of the week just specified
the specified month (
the given year (

Nota: in this case, the holiday program must begin and end
in the same day. Otherwise

for all months)

for all years)

is signaled.

- 37 -

User manual DY365

to set the program on the last day:

of all months of all years
of the specified VV month of all years
of all months of the specified ZZ year
of the specified VV month of the specified ZZ year

to set the program on the day XX (1,2,3...):

of all months of all years
of the specified VV month of all years
of all months of the specified ZZ year
of the specified VV month of the specified ZZ year

English

Program menu: new astro night

English

- 38 -

User manual DY365

Choose

nights

Nights

programs

How to select nights

scroll through the nights of the week from the first (1-2) to the last (7-1):

- by pressing the key

- by pressing the key

key to move to the next night without selecting the current night
to select/deselect the current night and move to the next

How to interpret the selection

If the night between the days of A and B is selected, the day A is on and underlined while B is on (not underlined).
Examples of selection:

Selected nights: between day 1 and 2, between day 2 and 3, between day 3 and 4, between day 4 and 5
Selected nights: between day 1 and 2, between day 2 and 3, between day 4 and 5

Selected nights: between day 1 and 2, between day 3 and 4, between day 7 and 1

- 39 -

User manual DY365

English

Night programs

English

Turning on at sunset, turning off at sunrise.
No parameter required.

Off from sunset to sunrise.
No parameter required.

Turning on at sunset, turning off during the
night. Turning on during the night, turning
off at sunrise.
Choose one of the three following cases:

Turning on at sunset, turning off at a
settable time.
Turning on at a settable time, turning off
at sunrise. (*)

Turning on at sunset, turning off after a
settable time interval.
Turning on before sunrise of a settable
time interval, turning off at sunrise.

* If off time is before sunset switching is not carried out. If on

time is after sunrise switching is not carried out.

** Switching on continues for the entire set time interval (also

if off time is after sunrise).

*** Switching on occurs before sunrise of the entire set time

interval (also if on time is before sunset).

- 40 -

User manual DY365

Turning on at sunset for a settable short
duration (pulse, max 59 seconds).
Turning on at sunrise for a short settable
duration (pulse, max 59 seconds).

Turning on at sunset, turning off during
the night.
Choose one of the three following cases:

Turning on during the night, turning off at
sunrise.
Choose one of the three following cases:

Turning on at sunset, turning off at a
settable time. (*)(**)

Turning on at sunset, turning off after a
settable time interval. (**)

Turning on at sunset for a settable short
duration (pulse, max 59 seconds).

User manual DY365

- 41 -

Turning on at a settable time, turning off
at sunrise. (*)(***)

Turning on before sunrise of a settable
time interval, turning off at sunrise. (***)

Turning on at sunrise for a settable short
duration (pulse, max 59 seconds).

English

Program menu: new astro daily

English

Program parameters

- on/off: on time and off time

- on pulse: time and pulse duration
(maximum 59 seconds)

- off pulse: time and pulse duration
(maximum 59 seconds)

- 42 -

User manual DY365

Enter

program

parameters

Program menu: new astro weekly

Program parameters

- on/off: day (or days)* and on time, day (or
days) and off time

- on pulse: day (or days)* and pulse time,
pulse duration (max 59 seconds)

- off pulse: day (or days)* and pulse time,
pulse duration (max 59 seconds)

* See “Days selection” on page 27

- 43 -

User manual DY365

Enter

program

parameters

English

Program menu: new astro yearly (or monthly)

English

Program parameters

- on/off: on time and off time

- on pulse: time and pulse duration
(max 59 seconds)

- off pulse: time and pulse duration
(max 59 seconds)

- 44 -

User manual DY365

Enter

program

parameters

How to choose the day (or days) in an astro annual program (or monthly)

to set the program:

in the first, second, third, fourth or last week of the month
in / the day/s (Monday, ...) of the week just specified
the specified month (
the given year (

for all months)

for all years)

Note: the on event must correspond to the off in the same day. For

example, if the program includes two events on Monday and
on Wednesday, then there will be two off events on Monday
and on Wednesday. Otherwise

is signaled.

User manual DY365

- 45 -

to set the program on the last day:

of all months of all years
of the specified VV month of all years
of all months of the specified ZZ year
of the specified VV month of the specified ZZ year

to set the program on the day XX (1,2,3...):

of all months of all years
of the specified VV month of all years
of all months of the specified ZZ year
of the specified VV month of the specified ZZ year

English

Program menu: new astro holiday

English

HOLIDAY OFF: the relay is OFF from the

beginning to the end of holiday program.

HOLIDAY ON: the relay is ON from the

beginning to the end of holiday program.

Program parameters

- beginning of the program

- end of the program

- 46 -

User manual DY365

Enter

program

parameters

How to choose the day (or days) in a holiday astro program

to set the program:

in the first, second, third, fourth or last week of the month
in / the day/s (Monday, ...) of the week just specified
the specified month (
the given year (

for all months)

for all years)

Note: in this case, the holiday program must begin and end in the

same day. Otherwise

is signaled.

User manual DY365

- 47 -

to set the program on the last day:

of all months of all years
of the specified VV month of all years
of all months of the specified ZZ year
of the specified VV month of the specified ZZ year

to set the program on the day XX (1,2,3...):

of all months of all years
of the specified VV month of all years
of all months of the specified ZZ year
of the specified VV month of the specified ZZ year

English

Program menu: check

English

How to check a program

choose the channel: 1 ... 8
choose the period: daily, weekly, annual, holiday or night (when it is a channel of astronomical type)
choose the type: on/off, on pulse, off pulse or a night program (only if it is a channel of astronomical type)

Note: a program requires more screens to be displayed:

- press the key

- press the keys

to move from the first to the second part of the same program

and to switch from one program to another

- 48 -

User manual DY365

Indication of the

memory space

(76 of 450)

Choose the

channel

Choose the

period

Choose the

type

- 49 -

User manual DY365

Check

programs

English

Program menu: modify

English

How to modify or to delete a program

choose the channel: 1 ... 8
choose the period: daily, weekly, annual, holiday or night (only if it’s an astronomical channel)
choose the type: on/off, on pulse, off pulse or a night program (only if it’s an astronomical channel)

Note: a program requires more screens to be displayed:

- press the key

- press the keys

To modify: press for a long time (at least 3 seconds) the key
To delete: press for a long time and simultaneously the keys

to move from the first to the second part of the same program

and key to switch from one program to another

and

- 50 -

User manual DY365

Indication of the

memory space

(76 of 450)

Choose the

channel

Choose the

period

Choose the

type

- 51 -

User manual DY365

Modify/

Delete

programs

English

Program menu: copy

the origin

channel

English

“Copy” menu allows copying the programs of a channel (origin channel) on one or more channels (channels destination).
Note: the programs previously stored on the destination channels will be deleted.

* See “Channels selection” on page 27

- 52 -

User manual DY365

Select

Select the

destination

channel*

Program menu: delete

“Delete” menu is used to delete all stored programs on one or more channels.
Note: to delete one single program to see “modify” mode (see page 50).

* See “Channels selection” on page 27

- 53 -

User manual DY365

Selection of

channels to

be delete*

English

BUS VEMER MENUBLUETOOTH MENU

The Bluetooth menu allows you to enable or disable the Bluetooth interface and change the password used to associate your device
(smartphone or tablet) to DY365.
The device is supplied with deactivated Bluetooth interface. To activate it, it's enough to access Bluetooth menu and set a password different
from 000000. With Bluetooth menu it's possible to activate or deactivate the interface or change the password.
After changing the password the first time, it's not possible to set the value 000000.

To enable the Bluetooth interface:

set Bluetooth ON

English

Warning: to make the Bluetooth interface active, the DY365 must be mains powered and connected to the main page (see page 8). The
Bluetooth interface is therefore not active when browsing through the DY365 menus.

To disable the Bluetooth interface:

set Bluetooth OFF

In this way no communication can take place between your device and DY365. DY365 works with the settings and programs already set; any
changes or creation of new programs must be made by acting directly on the keyboard of DY365.

- 54 -

User manual DY365

2

Changing the password

Password change

The password is the 6-digit code required by the app for the first association between
DY365 and smartphone

Press the key for at least 3 seconds until the first digit of the password starts to

flash.

Set the first digit with the keys
keys and press the key to confirm and move
to the next digit.

Repeat step to set all 6 digits.

and

3s

After confirming the last digit, the display shows
the new password.
Press the key

to exit the menu.

- 55 -

User manual DY365

English

BUS ABB MENU

BUS MENU

DY365 enables you to control 8 independent channels but It has
two relays (for channels 1 and 2). With additional DY365 4CE or
DY365 2CE modules it’s possible to add some relays and associate
these relays to the channels of DY365.
The remote actuators and DY365 all together are named
“network”.

“Bus” menu allows you to configure or to test the connection
between DY365 and the actuators
several DY365 connected to the network

English

configure the outputs, to associate the channels of DY365

to the channels (relays) of the remote actuators

to test the connection, to verify the correct association among

the channels of DY365 and the channels (relays) of the

actuators
to send programs to the other DY365 connected to the network
to receive the programs from another DY365 connected to the

network

or share programs among

.

Note: during the configuration or channels test and during the

- 56 -

User manual DY365

reception of programs on the bus the switchings of all
channels are disabled.

- 57 -

User manual DY365

English

Simple network configuration (one DY365, one or more remote actuators)

1. On the remote actuator: activate “Channel configuration” mode (see the documentation supplied with the actuator)

2. On the DY365:

2.1 Select

and confirm with . DY365 verifies the uniqueness of its address and when the test is successful it displays

2.2 Press to continue. Choose with the keys and and the channel to configure of DY365

2.3 Press the key

for at least 3 seconds. After configuration, the channel flashes (2 times) and the message appears.

3s

English

To delete the configuration of a channel, select the channel (steps 2.1 and 2.2) and press simultaneously for 3 seconds the keys

Complex network configuration (several DY365 one or more remote actuators)

About the configuration of the network in the case of several connected DY365, contact ABB Technical Support.

- 58 -

User manual DY365

and

.

Connection test

The test is used to verify proper communication between DY365 and the remote actuator. It’s possible to test multiple channels
simultaneously*.
During the test a series of on-off commands are sent every 5 seconds to the relay in test. It’s possible to exit the test:

- by pressing the key

- by pressing the key

to exit the test and test another channel
to exit the test and return to the main page

* See “Channels selection” on page 27

- 59 -

User manual DY365

English

Programs copy on the bus

This function allows you to transfer programs from a DY365 to other DY365 connected to the same network. It’s possible:

- to force the transfer to all other DY365 connected to the network (

- to transfer programs only to DY365 on which the reception mode* has been activated ( )

English

)

only for

It’s not possible to select the programs to copy, the entire memory area is copied. The programs previously stored on DY365 destination
will be deleted.

 Warning. The function

overwrites the programs of all DY365 connected to the network: use with caution.

- 60 -

User manual DY365

* Reception programs on the bus

Activate reception mode (

). The DY365 remains in reception for 1 minute and this condition is signaled from the flashing

) to receive the programs from another connected DY365 (that transmits programs via the function

.

English

In the case where the reception is not successful the message
Reception programs can take place at any time (even if the reception mode is not activated). This happens if another DY365 connected to the
network transmits by using the function

.

- 61 -

User manual DY365

is displayed.

SYNC MENU

SYNC menu allows you to enable or disable the presence of the additional DY GPS or DY DCF77 modules. DY GPS allows you to capture the
information of date, time and location from satellites and then to transfer them to DY365. DY DCF77 allows you to capture the informations of
date and time. Both DY GPS and DY DCF77 are available as accessories. Synchronization occurs every 30 minutes.
In this way the time of DY365 is always synchronized and there are no drifts due to the tolerance of the oscillator which marks the time base.

To enable the presence of DY GPS:

set SyNC GPS

It’s also possible to display the status of the connection to DY GPS (ok, waiting, error).
From the status page, while by pressing the key for at least 3 seconds it’s possible to force data sending from DY GPS to DY365
(the display shows

English

To enable the presence of DY DCF77:

set SyNC dCF

It’s also possible to display the status of the connection to DY DCF77 (ok, waiting, error).
From the status page, while by pressing the key
(the display shows

To disable the presence of DY GPS / DY DCF77:

SyNC OFF

 set
If DY GPS or DY DCF77 modules are not connected, it’s advisable to set SyNC OFF to avoid displaying unnecessary information message

SyNC ERR on the start page of DY365 (see page 8).

Note: the internal oscillator which marks the time base allows DY365 to maintain the updated time even without the presence of DY GPS / DY

DCF77. In this case clock accuracy is ± 0.5 seconds per day.

).

for at least 3 seconds it’s possible to force data sending from DY DCF77 to DY365

).

- 62 -

User manual DY365

2

SYNC status

SYNC status

DY GPS / DY DCF77 modules receive a good signal for a correct synchronization.
In case of connection to a DY GPS module, the display of DY365 also shows the
number of hooked satellites (10 in this exemple).

DY GPS / DY DCF77 modules are not properly connected to DY365.
Check the wiring diagrams in this manual.

DY GPS / DY DCF77 modules do not receive a good signal for a correct synchronization.
If this condition persists for more than a few hours, it’s advisable to move DY GPS / DY DCF77 modules
in a different position.

- 63 -

User manual DY365

English

HOUR COUNTER MENU

“Hour counter” menu allows you to display the hours of use (relay on) of connected loads. The device has 8 counters, one for each channel.
The maximum value of the counters is 99999 hours (about 11 years); reached the maximum limit, the counter resets automatically.

To reset a counter:

1. select the desired channel

2. press the key

3. confirm by pressing

Note: it’s possible to reset all counters contemporary from the “Reset” menu (see page 66).

English

for 3 seconds until the display shows “ ”

(press to exit without zeroing)

- 64 -

User manual DY365

- 65 -

User manual DY365

English

RESET MENU

“Reset” menu allows you to restore the initial state of the device.

Available resets:

Settings reset: deletes all the carried out settings (except the language, PIN and the channel settings on the BUS)
Time programs reset: deletes all saved time programs
Holiday programs reset: deletes all saved holiday programs
Astro programs reset: deletes all saved astronomical programs
Counter reset: resets the counters of all channels
All reset: carries out all the above described resets and deletes the language, PIN protection and the channels settings on the bus

English

There is also another reset, of hardware type, which allows you to reset the device in case it responds to the pressing of the keys so
unexpectedly, without losing the carried out settings/programs (only the date and the time are lost).

To carry out a hardware reset:

1. press the key “R” with a sharp object

The hardware reset is also useful when you forget PIN protection. Reset, in fact, unlocks the keyboard for 3 minutes, the necessary time to
access the appropriate menu and check/disable PIN.

- 66 -

User manual DY365

- 67 -

User manual DY365

2

English

FIRMWARE MENU

This menu shows the firmware installed in the device, where:
022 is the revision index
05 is the month
20 is the day

English

- 68 -

User manual DY365

ERROR SIGNALS

When setting up programs, in case of a discrepancy, the following
error messages can occur:

On and off events with different frequency (each

on event must have an off event)

On and off concomitant events of the same

program

Two or more consecutive on events of the same

program / Two or more consecutive off events of

the same program
Invalid date
Insufficient memory
Attempt to set an on pulse on a channel where is

already stored an off pulse (see page 27)
Attempt to set an off pulse on a channel where is

already stored an on impulse (see page 27)
Attempt to set an on holiday program on a

channel where is already stored an off holiday

program (see page 27)
Attempt to set a holiday off program on a channel

where a holiday on program is already stored

(see page 27)

User manual DY365

Attempt to set an annual program of on and off

events on different days

Attempt to set an astro program on a channel of

time (see page 27)

Attempt to set a time program on a channel of

time type (see page 27)

Error accessing memory *

* In this case, carry out a hardware reset (see page 66).

If the error persists, contact ABB technical support

- 69 -

English

BATTERY MANAGEMENT

REFERENCE STANDARDS

When the battery is close to empty, on the first line of the display
appears
soon as possible.

To replace the battery:

- remove the cover of battery compartment

- replace the battery with one of 3V CR14250 type and put the
cover

In order not to lose the programming steps and carried out

English

settings, it is necessary to ensure that the time for the battery
replacement doesn’t exceed 60 seconds (in absence of power by
means).

Dispose of the used batteries observing the laws in force

in relation to the disposal of hazardous waste.

. In this case, the battery must be replaced as

EU CONFORMITY DECLARATION

ABB declares that the device complies with the EU directive
2014/53/EU (RED) with reference to the following standards:

• EN 60730-2-7

• ETSI EN 301 489-1

• ETSI EN 301 489-17

• ETSI EN 300 328

The complete text of EU conformity declaration is available at the
Internet address ABB - www.abb.com

- 70 -

User manual DY365

ABB S.p.A

V.le dell’Industria 18

20010 Vittuone (MI) - Italy

Tel. [phone]

https://new.abb.com/low-voltage

© Copyright 2019 ABB S.P.A . All rights reserved.

We reserve the right to make technical changes

or modify the contents of this document without prior notice.

2CSM441045D0201

10-2020