ABB DCS400 Spare PCB’s compatibility

Spare PCB’s compatibility Note:

The old PCB’s (

SDCS-CON-3 / -PIN-3 / -FIS-3

)

from

DCS

400 „classic“

can be replaced by

all or

new PCB’s

field choke

must not

replaced

by a new field choke type.

like (SDCS-CON-3 A / -PIN-3A / -FIS-3A). The existing
The DCS 400 Rev. A expect PCB’s with index A only.

single

SDCS-FIS-3

SDCS-PIN-3

SDCS-CON-3

Firmware:

< = 108.0

DCS400 “classic”

or

or

or

old choke (inside)

SDCS-FIS-3A

SDCS-PIN-3A

SDCS-CON-3A

Firmware:

> = 108.0

DCS 400 „classic“ , permissible configuration

Config. SDCS- SDCS- SDCS-

firmware / panel

107.x / 3.00

1 -CON-3 -PIN-3 -FIS-3

or

108.0 / 4.00

107.x / 3.00

2 -CON-3 -PIN-3 -FIS-3A

or

108.0 / 4.00

107.x / 3.00

3 -CON-3 -PIN-3A -FIS-3

or

108.0 / 4.00

107.x / 3.00

4 -CON-3 -PIN-3A -FIS-3A

or

108.0 / 4.00

5 -CON-3A -PIN-3 -FIS-3 108.0 / 4.00
6 -CON-3A -PIN-3 -FIS-3A 108.0 / 4.00
7 -CON-3A -PIN-3A -FIS-3 108.0 / 4.00
8 -CON-3A -PIN-3A -FIS-3A 108.0 / 4.00

• SDCS-CON-3 runs with firmware 107.x or 108.0,

SDCS-CON-3 A runs with 108.0 only.

• Caution:
Even, if all PCB’s are replaced by new PCB’s with
index A, the unit is still a DCS 400 “classic”!
Therefore use panel function Set Typecode and
select Revision = without.

DCS400 Rev.A

SDCS-FIS-3A

SDCS-PIN-3A

SDCS-CON-3A

Firmware:

> = 108.0

new choke (inside)

SDCS-FIS-3

SDCS-PIN-3

SDCS-CON-3

Firmware:

< = 108.0

DCS 400 Rev. A , permissible configuration

Config. SDCS- SDCS- SDCS-

firmware / panel

1 -CON-3A -PIN-3A -FIS-3A 108.0 / 4.00

• New PCB’s with index A can be replaced by new
PCB’s with index A, only!

Therefore use panel function Set Typecode and
select Revision = Rev A.x

Compatibility: DCS 400 „classic“ / DCS 400 Rev A

Feature Advanced , new

Hardware Configuration

other board configurations

are not allowed

(*) started at converter serial

no. 7035270A0258146

Drive Firmware Version 108.0 107.3 108.0 108.0
DCS400PAN Version 4.00 3.00 4.00 4.00
Documentation 3ADW 000 095

Resolution:

Analog Inputs 1+2

Accuracy

Analog Outputs 1+2

Accuracy

Tacho Input

Accuracy

Analog Outputs 1+2

max. scaling 11.00V 10.00V 10.00V 11.00V

DCS 400 Rev A

SW 108.0

SDCS-CON-3A

SDCS-PIN-3A

SDCS-FIS-3A

new choke (inside)

R0501 Rev E

12 bits incl. sign

0,05%

12 bits incl. sign

0,05%

12 bits incl. sign

0,06%

„Classic“ DCS 400

without Rev.

SW 107.x

SDCS-CON-3

SDCS-PIN-3

SDCS-FIS-3 or

SDCS-FIS-3A (*)

old choke (inside)

3ADW 000 095

R0401 Rev D

10 bits incl sign

0,2%

8 bits incl. sign

0,8%

10 bits incl. sign

0,25%

„Classic“ DCS 400

without Rev.

but

SW 108.0

SDCS-CON-3

SDCS-PIN-3

SDCS-FIS-3 or

SDCS-FIS-3A

old choke (inside)

HW: …Rev D

SW: …Rev E

10 bits incl sign

0,2%

8 bits incl. sign

0,8%

10 bits incl. sign

0,25%

„Classic“ DCS 400

without Rev.

but CON-3A

SW 108.0

SDCS-CON-3A

SDCS-PIN-3 or

SDCS-PIN-3A

SDCS-FIS-3 or

SDCS-FIS-3A

old choke (inside)

PIN-3 / FIS-3: Rev D

CON-3A / SW: Rev E

12 bits incl. sign

0,05%

12 bits incl. sign

0,05%

12 bits incl. sign

0,06%

Field Voltage range
Field Current range:

A1 (20…25A unit)
A1 (45…140A unit)

A2
A3
A4

New Features:

Tacho Offset Adjustment l l l

Control of Bridge 1

by Digital Input l l l

Control of Bridge 2

by Digital Input

Parameter and Signal for

Arm Curr Level

Signal for Speed Ref at

Ramp Generator Input l l l

Signal for

Field Current actual is ok l l l

Signal for Speed

Measurement Fault

Signal for

Mains Voltage Low

Fault Logger

power failure save l l l

50V…440V

0,1… 4A

0,1… 6A
0,3…16A
0,3…16A
0,3…20A

l l l

l l l

l l l

l l l

50V…350V 50V…350V 50V…350V

0,1… 6A

0,1… 6A
0,3…12A
0,3…14A
0,3…16A

0,1… 6A

0,1… 6A
0,3…12A
0,3…14A
0,3…16A

0,1… 6A

0,1… 6A
0,3…12A
0,3…14A
0,3…16A

Note:

• The old PCB’s (SDCS-CON-3 / -PIN-3 / -FIS-3 ) from DCS 400 „classic“ can be replaced by all or
single new PCB’s like (SDCS-CON-3 A / -PIN-3A / -FIS-3A).

• The existing field choke must not replaced by a new field choke type.

• The DCS 400 Rev. A expect PCB’s with index A only.