AAXA ST200 User Manual
aaxa
TECHNOLOGIES
User Guide
Caution!
WARNING: Please use this product as instructed. Misuse may cause
injury or death.
DO NOT use while driving.
DO NOT expose to water or wet
surfaces. Electric shock may occur.
DO NOT expose the projected LED
image to your eyes or the eyes of
others.
DO NOT block or restrict airow
from ventilation holes as this may
cause the projector to overheat.
Keep the projector, battery, or
charger away from any heat
sources.
Caution for Battery Use
• Do not pierce or puncture the battery
with sharp objects.
• Do not heat the product or expose it to
high temperature.
• Do not wet it or place it in any liquid.
Caution for Headphone Use
• Prolonged use at high volume may
impair your hearing.
• High volume during walking or driving
may cause distractions and result in
injury or death.
Table of Contents
Chapter 1: ST200 at a glance
Main Unit Front/Back
1
Remote & Keypad
2
Accessories
3
Chapter 2: Getting Started
Powering On / OFF
4
Focus Adjustment / Short-Throw
5
Optics
Battery Installation
6
Connecting to a Computer VGA
7
Connecting to a Computer HDMI
9
Connecting to Composite Video
11
Connecting to HDMI Video
13
Connecting to Speaker or Head-
15
phones
16
Connecting a Micro SD Card
18
Connecting to a USB Host
Chapter 3: Menu Screens
20
Portable Media Player
21
Video Player Menu
23
Video FAQ
24
Photo Viewer Menu
26
Photo FAQ
27
Music Player Menu
29
Music FAQ
30
Ebook Viewer Menu
31
Setup Menu
36
Keystone Adjustments
38
Chapter 4: Technical Details
39
Troubleshooting
40
Specications
ST200 at a Glance
Chapter 1
Main Unit Front/Back
HDMI
Headphone Out
AV Input
USB Port
Power Button
DC Power
VGA Input
Micro SD Card
Power Switch
Focus Wheel
1
Remote & Keypad
Direction Pad
Power On/Off
Main Menu
Navigation
Both the keypad and remote can be used to navigate through the menus. The “Main Menu
Navigation” on the remote functions exactly the same as the directional pad on the ST200
unit. The Media Player Menu Navigation allows you to control the media you are currently
playing. There is also an Input source button and a keystone up/down on the remote control.
You may also control the volume with the mute button or with the volume up and volume
down buttons.
Select Source
Media Player Menu
Navigation
Input Exit/Back
On / Off
NOTICE: Pressing power on the remote will only put the projector in STANDBY
mode. Please switch the On / Off switch of the projector to the “Off” position if you
want to turn it off.
2
Accessories
Tripod
Power Adapter
*Under various circumstances, the actual accessories may be different from
those shown in the pictures above.
Remote
VGA Cable
A/V Cable
3
Getting Started
Chapter 2
Powering ON the projector
1. Connect the power cord to the ST200.
2. Connect the wall plug into the wall power source.
3. Switch the On/Off switch on the side of the projector to the “On” position. The
projector should turn on automatically. If the projector does not turn on automatically with the On/Off switch to “On” position press the power button on the top of the
projector or press the power button on the remote control.
Standby Mode
1. Stand By Mode – To enter “stand by mode” press the power button on top of the
projector twice. This will put the projector into “stand by mode”. In “stand by mode”
the projector is idle but is able to be powered on with the remote control or “wake up
feature” (custom models only). “Stand by mode” consumes power even when the
projector is idle.
Powering OFF the projector
1. Switch the On/Off switch to “Off” to turn off the projector.
Note: The ST200 Projector battery does not charge when the projector is in
operation.
4
Focus Adjusment /Short-Throw Optics
Focus Adjustment
• Spin the focus wheel left or right until the image becomes clear.
Short-Throw Optics
• The ST200 incorporates a short-throw optical system. Shortthrow optics have the advantage of delivering a brighter and
larger image at a shorter “throw” distance. The calculation of a
projector’s throw ratio is (distance / picture width) and the ratio
for the ST200 is 0.8.
Throw Distance Chart
Distance inch (“)
12
24
36
48
60
72
Diagonal Inch (“)
17
34
52
69
86
103
Throw Ratio 0.8
*minimum throw distance: 10 inches
16:9 Aspect Ratio
DIAGONAL SCREEN SIZE
5
Installing the Battery Pack
Step 1. Unplug ST200 from the power adapter and power switch to “OFF”
position.
Step 2. Remove the (3) screws holding the battery to ST200 casing.
Step 3. Remove the battery casing and disconnect battery from receptacle.
Step 4. Connect the new battery harness to the receptacle on the PCBA.
Step 5. Install the battery until it ts in correctly onto the ST200 and reinstall the (3) screws
Note: The ST200 Projector already comes with the battery preinstalled.
6
Connecting to a Computer via VGA
Step 1:
Connect the large end of the
Step 2:
Connect the small end of the
Step 3:
In the Main Menu
VGA Cord
VGA Cord
to your computer’s
VGA Adapter
to your ST200’s
VGA Adapter
Select “VGA” icon Select “INPUT” icon
7
Connecting to a Computer Cont.
Step 4:
Enabling VGA or HDMI output on your Computer – To enable VGA or HDMI output on your computer most computers require “turning on” the video output feature. Each computer is different.
Please consult your owner’s manual for instructions to enable VGA or HDMI output. Below are
standard instructions for a Windows 7 computer – not all systems are the same.
Step 5:
Press Windows+P to toggle through
display settings. Select either “Duplicate” or “Extend” depending on
your viewing option.
*NOTE: different operating systems
may differ
Step 6:
1. Right click on computer
desktop and select “Screen
Resoluton”.
2. Display Properties window
will pop up.
3. If a secondary monitor is
grayed out, click on it and select “Extend these displays”
in the “Multiple Displays” drop
down.
4. If the image is blurry or the
text is not legible, adjust
the screen resolution. We
recommend 1280x720.
8
Connecting to a Computer via HDMI
Step 1:
Connect one end of the
Step 2:
Connect one end of the
Step 3:
In the Main Menu
Select “INPUT” icon
HDMI Cord
HDMI Cord
to your computer’s
HDMI Adapter
to your ST200s
HDMI Adapter
Select “HDMI” icon
9
Connecting to a Computer Cont.
Step 4:
Enabling VGA or HDMI output on your Computer – To enable VGA or HDMI output on your computer most computers require “turning on” the video output feature. Each computer is different.
Please consult your owner’s manual for instructions to enable VGA or HDMI output. Below are
standard instructions for a Windows 7 computer – not all systems are the same.
Step 5:
Press Windows+P to toggle
through display settings. Select
either “Duplicate” or “Extend” depending on your viewing option.
*NOTE: different operating systems may differ
Step 6:
1. Right click on computer
desktop and select “Screen
Resolution”.
2. Display Properties window
will pop up.
3. If a secondary monitor is
grayed out, click on it and select “Extend these displays”
in the “Multiple Displays” drop
down.
4. If the image is blurry or the
text is not legible, adjust
the screen resolution. We
recommend 1280x720.
10
Connecting to Composite Video
Step 1:
Connect one end of the
Step 2:
Connect opposite end of
to your ST200’s
Composite Cord
to your devices
Composite Cord
A/V Adapter
Composite Cord
11
Loading...