AAXA P5 User Manual

aaxa

TECHNOLOGIES

User Guide

Caution!

WARNING: Please use this product as instructed. Misuse may cause
injury or death.

DO NOT use while driving

DO NOT expose to water or wet
surfaces. Electric shock may occur.

DO NOT expose the projected LED
image to your eyes or the eyes of
others

DO NOT block or restrict airow

from ventilation holes as this may
cause the projector to overheat

Keep the projector, battery, or
charger away from any heat sources

Caution for Battery Use

• Do not pierce or puncture the battery
with sharp objects

• Do not heat the product or expose it to
high temperature.

• Do not wet it or place it in any liquid

Caution for Headphone Use

• Prolonged use at high volume may
impair your hearing.

• High volume during walking or driving
may cause distractions and result in
injury or death

Table of Contents

Chapter 1: P5 at a Glance

P5 Introduction
Remote & Keypad
Accessories

Chapter 2: Getting Started

Powering On / OFF
Swappable Battery
Focus Adjustment / Throw
Distance
External Input/Outputs
Connecting to a Computer VGA
Connecting to a Computer HDMI
Connecting to Composite Video
Connecting to HDMI Video
Connecting to Speaker or
Headphones

Connecting a Micro SD Card
Connecting a USB Stick

1

Chapter 3: Menu Screens

2

Main menu

3

Video Player Menu
Photo Viewer Menu

4

Music Player Menu

5

Ebook Viewer Menu

Chapter 4: Setup Menu

7

Settings

8

Brightness Feature

9

Keystone

11

Chapter 5: Technical Details

13

Troubleshooting

15

Specications

Notes

17

18
20

22
23
27
31
34

35
39
41

43
45
46

P5 at a Glance

Chapter 1

Main Unit Front/Back

Focus Adjustment

HDMI

VGA Port

AV Port

Headphone Out

USB Port

Power Button

Power Switch

Micro SD Card

1

Remote & Keypad

Direction Pad

OK

On / Off

Power On/Off

Main Menu

Navigation

Volume Down

Keystone

Select Source

Volume Up

Keystone

Media Player

Menu Navigation

LED Lights

Input Exit/Back

Remote

Both the keypad and remote can be used to navigate through the menus. The Main Menu
Navigation on the remote functions exactly the same as the directional pad on the P5 unit.

NOTICE: Pressing power on the remote will only put the projector in STANDBY mode.
Toggle the “ON/OFF” switch on the side of the projector to fully turn the projector

off.

2

Accessories

Tripod

Power Adapter

*Under various circumstances, the actual accessories may be different from
those shown in the pictures above.

Remote

VGA Cable

A/V Cable

3

Getting Started

Chapter 2

Powering ON the projector

1. Connect the power cord to the P5.

2. Connect the other end of the power cord into the wall power source.

3. Toggle the On / Off switch on the side of the projector to the “ON” position --the
projector should automatically turn on.

4. If the projector does not automatically turn on with the “Power Switch” toggled to the
“ON” position, press the “ON/OFF POWER” button on the keypad and hold for

2-3 seconds to start the projector

Standby Mode

1. To transition to “STANDBY” mode, press the power button twice on the keypad or
the remote control.

2. The optical engine should power off and the fan should stop spinning. The projector
is now in “STANDBY” mode and can be turned on using the remote control.

*Note: Standby mode will still consume a small amount of power.

Powering OFF the projector

1. To turn off the projector, toggle the “Power Switch” to the “OFF” position. This will
fully turn off the projector.

4

Swappable Lithium Ion Battery

The P5 Features a 135 minute, 22 Watt, Swappable Lithium Ion Battery Pack.
This battery pack is designed to be interchangeable with spare battery packs and
can be removed and replaced as needed.

This battery pack can only be charged by connecting to the P5 projector while the
power supply is plugged in. This battery pack does NOT charge while the projec­tor is in operation. Additional battery packs can be purchased at www.aaxatech.

Shown: P5 Lithium Ion Battery

*CAUTION! Lithium Ion Battery Packs store a lot of energy and can be dangerous. Lithium
Ion Battery Packs should always be treated with care and properly disposed. Do not mis­use, do not put near a heat source, do not open.

5

Battery Installation

Removing Battery

1. Locate the battery locking mechanisms underneath the projector

2. Slide the two locking mechanisms outwards

3. Gently slide the Battery Pack out by pushing the battery pack away from the projec­tor

Installing the Battery

1. Reverse the removal instructions and ensure the battery is properly connected to the
guide clips

6

Focus Adjusment / Throw Distance

Focus Adjustment

• Spin the focus wheel up or down until the image becomes
clear.

Throw Distance Chart

Throw Distance

Units: Inches

10
20
30
40
50
60
70
80

Throw Ratio 1.47
Projection Angle: 100% Offset

*minimum throw distance: 10 inches

Diagonal Size

Units: Inches

8
16
23
31
39
47
55
62

DIAGONAL SCREEN SIZE

16:9 Aspect Ratio

7

External Inputs and Outputs

USB Stick

MicroSD

VGA

HDMI

Composite Cable

Headphones/speakers

8

Connecting to a Computer via VGA

Step 1:

Connect one end of the VGA Cable
to your computer’s VGA Adapter.

Step 2:

Connect the other end of the
VGA Cord to your P5’s VGA port.

Step 3:

In the Main Menu Select the “Inputs” icon and then the “VGA” Icon.

Select “VGA” icon Select “INPUT” icon

9

Connecting to a Computer Cont.

Step 4:

Enabling VGA or HDMI output on your Computer – To enable VGA or HDMI output on your com­puter most computers require “turning on” the video output feature. Each computer is different.
Please consult your owner’s manual for instructions to enable VGA or HDMI output. Below are
standard instructions for a Windows 7 computer – not all systems are the same.

Step 5:

Press Windows+P to toggle
through display settings. Select
either “Duplicate” or “Extend” de­pending on your viewing option.

*NOTE: different operating sys­tems may differ

Step 6:

1. Right click on computer
desktop and select “Screen
Resolution”

2. Display Properties window
will pop up

3. If a secondary monitor is
grayed out, click on it and se­lect “Extend these displays”
in the “Multiple Displays” drop
down

4. If the image is blurry or the
text is not legible, adjust
the screen resolution. We
recommend 1280x720.

10

Connecting to a Computer via HDMI

Step 1:

Connect one end of the HDMI Cable
to your computer’s HDMI Adapter.

Step 2:

Connect the other end of the HDMI
Cord to your P5’s HDMI port.

Step 3:

In the Main Menu Select the “Inputs” icon and then the “HDMI” Icon.

Select “INPUT” icon

Select “HDMI” icon

11

Connecting to a Computer Cont.

Step 4:

Enabling VGA or HDMI output on your Computer – To enable VGA or HDMI output on your com­puter most computers require “turning on” the video output feature. Each computer is different.
Please consult your owner’s manual for instructions to enable VGA or HDMI output. Below are
standard instructions for a Windows 7 computer – not all systems are the same.

Step 5:

Press Windows+P to toggle
through display settings. Select
either “Duplicate” or “Extend” de­pending on your viewing option.

*NOTE: different operating sys­tems may differ

Step 6:

1. Right click on computer
desktop and select “Screen
Resolution”

2. Display Properties window
will pop up

3. If a secondary monitor is
grayed out, click on it and se­lect “Extend these displays”
in the “Multiple Displays” drop
down

4. If the image is blurry or the
text is not legible, adjust
the screen resolution. We
recommend 1280x720.

12