AAXA P450 User Manual
aaxa
TECHNOLOGIES
PICO PROJECTOR
User Guide
Caution!
WARNING: Please use this product as instructed. Misuse may cause
injury or death.
DO NOT use while driving
DO NOT expose to water or wet
surfaces. Electric shock may occur.
DO NOT expose the projected LED
image to your eyes or the eyes of
others
DO NOT block or restrict airow
from ventilation holes as this may
cause the projector to overheat
Caution for Headphone Use
• Prolonged use at high volume may
impair your hearing.
• High volume during walking or driving
may cause distractions and result in
injury or death
Table of Contents
Chapter 1: P450 at a glance
P450 Introduction
Remote & Keypad
Accessories
Chapter 2: Getting Started
Powering On / OFF
Focus Adjustment / Throw
Distance
External Input/Outputs
Connecting to a Computer VGA
Connecting to a Computer HDMI
Connecting to Composite Video
Connecting to HDMI Video
Connecting to Speaker or
Headphones
Connecting a Micro SD Card
Connecting a USB Stick
1
Chapter 3: Menu Screens
2
Main menu
3
Video Player Menu
Photo Viewer Menu
4
Music Player Menu
Ebook Viewer Menu
5
Chapter 4: Setup Menu
6
Picture Settings
7
Keystone Adjustment
9
Chapter 5: Technical Details
11
Troubleshooting
13
Specications
Notes
15
16
18
20
21
24
27
30
32
36
38
40
41
P450 at a Glance
Chapter 1
Main Unit Front/Back
Focus Adjustment
Headphone Out
VGA Port
USB Port
Power Button
Power Switch
Micro SD Card
HDMI
AV Input
Power Adapter Port
1
Remote & Keypad
Direction Pad
OK
On / Off
Power On/Off
Main Menu
Navigation
Volume Down
Keystone
Select Source
Volume Up
Keystone
Media Player
Menu Navigation
LED Lights
Input Exit/Back
Remote
Both the keypad and remote can be used to navigate through the menus. The Main Menu
Navigation on the remote functions exactly the same as the directional pad on the P450 unit.
NOTICE: Pressing power on the remote will only put the projector in STANDBY mode.
Toggle the “ON/OFF” switch on the side of the projector to fully turn the projector
off.
2
Accessories
Tripod
Power Adapter
*Under various circumstances, the actual accessories may be different from
those shown in the pictures above.
Remote
A/V Cable
VGA Cable
3
Getting Started
Chapter 2
Powering ON the projector
1. Connect the power cord to the P450.
2. Connect the other end of the power cord into the wall power source.
3. Toggle the On / Off switch on the side of the projector to the “ON” position --the
projector should automatically turn on.
4. If the projector does not automatically turn on with the “Power Switch” toggled to the
“ON” position, press the “ON/OFF POWER” button on the keypad and hold for 2-3
seconds to start the projector
Standby Mode
1. To transition to “STANDBY” mode press and hold the power button on the keypad or
the remote control for 3 seconds.
2. The optical engine should power off and the fan should stop spinning. The projector
is now in “STANDBY” mode and can be turned on using the remote control.
*Note: Standby mode will still consume a small amount of power.
Powering OFF the projector
1. To turn off the projector, toggle the POWER Switch to the “OFF” position. This will
fully turn off the projector.
*The P450 is NOT battery powered and does not have the option for a battery
4
Focus Adjusment / Throw Distance
Focus Adjustment
• Spin the focus wheel up or down until the image becomes
Throw Distance Chart
Throw Distance
Units: Meters
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
Throw Ratio 1.40
Projection Angle: 39.3 degrees
*minimum throw distance: 12 inches
Diagonal Size
Units: Inches
17
33
50
66
83
99
116
133
DIAGONAL SCREEN SIZE
16:95 Aspect Ratio
5
External Inputs and Outputs
USB Stick
MicroSD
Laptop
HDMI
Composite Cable
Headphones/speakers
6
Connecting to a Computer via VGA
Step 1:
Connect one end of the VGA Cable
to your computer’s VGA Adapter.
Step 2:
Connect the other end of the VGA
Cord to your P450’s VGA port.
Step 3:
In the Main Menu Select “Inputs” icon and then the “VGA” Icon.
Select “VGA” icon Select “INPUT” icon
7
Connecting to a Computer Cont.
Step 4:
Enabling VGA or HDMI output on your Computer – To enable VGA or HDMI output on your computer most computers require “turning on” the video output feature. Each computer is different.
Please consult your owner’s manual for instructions to enable VGA or HDMI output. Below are
standard instructions for a Windows XP computer – not all systems are the same.
Step 5:
Press function & “F5” to instruct
the computer to enable multiple
displays.
You can also press Windows+P to
toggle through display settings.
*NOTE: different operating systems may differ
Step 6:
1. Right click on computer desktop and select “Properties”
2. Display Properties window
will pop up
3. Click on the “Settings” Tab
4. If a secondary monitor is
grayed out, click on it and
check “Extend my Windows
Desktop onto this monitor”
5. If the image is blurry or the
text is not legible, adjust
the screen resolution. We
recommend 1280x800.
8
Connecting to a Computer via HDMI
Step 1:
Connect one end of the HDMI Cable
to your computer’s HDMI Adapter.
Step 2:
Connect the other end of the HDMI
Cord to your P450’s HDMI port.
Step 3:
In the Main Menu Select “Inputs” icon and then the “HDMI” Icon.
Select “INPUT” icon Select “HDMI” icon
9
Connecting to a Computer Cont.
Step 4:
Enabling VGA or HDMI output on your Computer – To enable VGA or HDMI output on your computer most computers require “turning on” the video output feature. Each computer is different.
Please consult your owner’s manual for instructions to enable VGA or HDMI output. Below are
standard instructions for a Windows XP computer – not all systems are the same.
Step 5:
Press function & “F5” to instruct
the computer to enable multiple
displays.
You can also press Windows+P to
toggle through display settings.
Step 6:
1. Right click on computer desktop and select “Properties”
2. Display Properties window
will pop up
3. Click on the “Settings” Tab
4. If a secondary monitor is
grayed out, click on it and
check “Extend my Windows
Desktop onto this monitor”
5. If the image is blurry or the
text is not legible, adjust
the screen resolution. We
recommend 1280x800.
*NOTE: different operating systems may differ
10
Connecting to Composite Video
Step 1:
Connect the 3.5mm Composite A/V
Cable to the back of the P450.
Step 2:
Connect the composite end of
the AV Cable (Red, White,Yellow)
to your device.
11
Loading...