A and D UA-1030 User Manual [es]

Premier Talking Blood Pressure moniTor

Models UA-1030T + UA-1030TCN

Instruction Manual

Manuel d'instructions

Manual de instrucciones

englishFrançaisesPañol

THIS MONITOR IS CLINICALLY VALIDATED

IMPORTANT INFORMATION

This blood pressure monitor was clinically validated by an independent organization. Blood pressure measurements determined with this device are equivalent to those obtained by a trained observer using the cuff/stethoscope auscultation method within the limits prescribed by the American National Standard Institute (ANSI/AAMI SP10) for electronic sphygmomanometers. The published study was performed by a reviewing committee consisting of physicians and/or nurses. Among blood pressure manufacturers, A&D Medical is proud to have the highest number of Clinically Validated monitors with a positive recommendation from professionals that are available to consumers.

Please read this important information before using your monitor.

Please remember that only a medical practitioner is qualified to interpret

☞

your blood pressure measurements. Use of this device should not replace regular medical examinations.

Consult your physician if you have any doubt about your readings.

☞

Should a mechanical problem occur, contact A&D Medical in the U.S.A. at 1-888-726-9966 or contact Auto Control in Canada at 1-800-461-0991.

Do not attempt to service, calibrate, or repair this monitor.

☞

Because your UA-1030T monitor contains delicate, high-precision parts,

☞

avoid exposing it to extremes in temperature or humidity or to direct sunlight, shock and dust. A&D Medical guarantees the accuracy of this monitor only when it is stored and used within the temperature and humidity ranges noted on page E-27.

Clean the monitor and cuff with a dry, soft cloth or a cloth dampened with

☞

water and a mild detergent. Never use alcohol, benzene, thinner or other harsh chemicals to clean monitor or cuff.

Remove and replace batteries if monitor is not used for more than six

☞

months. Alkaline batteries recommended.

PRECAUTIONS

The UA-1030T is designed to be used at home, by those who are eighteen (18) years and older, to monitor blood pressure (systolic and diastolic) and pulse rate. It is not designed for ambulatory use.

IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

DANGER - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

CAREFULLY FOLLOW THESE INSTRUCTIONS.

Use appropriate AC adapter and converter(s) when outside the U.S.A.

☞

E-1

A&D Medical (Toll-Free): 1-888-726-9966

In Canada - Auto Control Medical (Toll-Free): 1-800-461-0991

E-2

Fast. Easy. Accurate.

Congratulations on purchasing a state-of-the-art A&D Medical blood pressure monitor—one of the most technologically advanced monitors available today. Designed for ease of use and accuracy, this monitor will facilitate your daily blood pressure regimen.

Physicians agree that daily self-monitoring of blood pressure is an important step individuals can take to maintain cardiovascular health and prevent the serious consequences associated with undetected and untreated hypertension.

TABLE OF CONTENTS

VALIDATION STATEMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E-1

IMPORTANT INFORMATION ...........................................E-2

MANUFACTURER'S STATEMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-3

TABLE OF CONTENTS ...............................................E-4

WHAT DISPLAY SYMBOLS MEAN ..................................E-5 – E-6

MONITOR COMPONENTS .............................................E-7

HOW UA-1030T WORKS .............................................E-8

BEFORE YOU START ................................................E-8

SELECTING THE CORRECT CUFF SIZE ....................................E-9

ADJUSTING THE CLOCK .............................................E-10

ADJUSTING THE PRESSURE .........................................E-10

TRICHECK™ MODE ...............................................E-11

TAKING YOUR BLOOD PRESSURE ................................ E-12 – E-13

MEASUREMENT USING TRICHECK .....................................E-14

MEASUREMENT WITH SET PRESSURE ..................................E-15

MEASUREMENT WITH DESIRED SYSTOLIC PRESSURE ......................E-15

WHAT IS AN IRREGULAR HEARTBEAT ..................................E-16

ABOUT THE PRESSURE RATING INDICATOR™ ............................E-17

ABOUT MEMORY .................................................E-18

ADJUSTING THE SPEAKER VOLUME ....................................E-19

SELECTING THE LANGUAGE ..........................................E-19

A&D Medical has been manufacturing high quality healthcare products for over 20 years. We are committed to providing you and your family with monitoring devices that provide the utmost in accuracy and convenience.

A&D Medical - Designed for Life.

E-3

A&D Medical (Toll-Free): 1-888-726-9966

USING THE MONITOR WITH AC ADAPTER ...............................E-20

ABOUT BLOOD PRESSURE ..................................... E-21 – E-25

TROUBLESHOOTING ...............................................E-26

SPECIFICATIONS .................................................E-27

CONTACT INFORMATION ............................................E-28

FRENCH INSTRUCTIONS .............................................F-1

SPANISH INSTRUCTIONS ............................................S-1

LOGBOOK PAGES ..................................................L-1

In Canada - Auto Control Medical (Toll-Free): 1-800-461-0991

E-4

WHAT DISPLAY SYMBOLS MEAN

Symbols that are printed on the device case

Symbols Function / Meaning Recommended Action

Standby and turn the device on.

R6(AA)

Battery installation guide Direct current

SN Serial number

2010

Date of manufacture Type BF: Device, cuff and tubing are

designed to provide special protection against electrical shock.

0366

EC directive medical device label WEEE label

Manufacturer

EC REP

EU-representative

Symbols that appear on the display

Symbols Function / Meaning Recommended Action

Appears while measurement is in progress. It blinks when the pulse is detected.

Irregular Heartbeat symbol (I.H.B.) Appears when an irregular heartbeat is detected during measurement.

Measurement is in progress. Remain as still as possible.

TriCheck mode Takes three consecutive measurements automatically and displays the average values of the three measurements.

The reading may yield an incorrect value. Take another measurement. Remain still during measurement.

A&D Medical (Toll-Free): 1-888-726-9966

E-5

Appears when a body or arm movement is detected.

Symbols Function / Meaning Recommended Action

The reading may yield an Appears during measurementwhen the cuff is applied loosely.

incorrect value. Apply the

cuff correctly, and take

another measurement. Previous measurements stored in memory

Average data

The battery power indicator during

Full Battery

Low Battery

measurement.

The battery is low when it blinks.

Unstable blood pressure due to movement during measurement.

Replace all batteries with new

ones when the mark blinks.

Take another measurement.

Remain still during

measurement. Thesystolic and diastolic values are

within 10 mmHg of each other. The pressure value did not increase

during the inflation.

The cuff is not applied correctly.

PUL. DISPLAY ERROR

The pulse is not detected correctly.

Apply the cuff correctly,

and take another

measurement.

Remove the batteries and press theSTART button,

Blood pressure monitor internal error

SYS.

DIA.

PUL./min.

Systolic blood pressure in mmHg Diastolic blood pressure in mmHg Pulse per minute Data taken between 4:00 and 9:59

Data taken between 18:00 and 1:59

Pressure settings Indicates the pressure value as set

by the user.

In Canada - Auto Control Medical (Toll-Free): 1-800-461-0991

and then install the batteries again. If the error still appears, contact the A&D.

E-6

MONITOR COMPONENTS

Battery Compartment

Display

Air Hose

AC Adapter Jack

START Button

Air Connector Plug

Air Socket

Display

1.5V Batteries

(AA, LR6 or R6P)

SET Button

Button Button

Battery Cover

Button

VOLUME

Arm Cuff

Speaker

HOW UA-1030T WORKS

Battery Compartment

WHO Classification Indicator

E-7

Air Connector Plug Arm Cuff

Air Hose

(Irregular heartbeat symbol)

Cuff Fit Error Symbol

Movement Error Symbol

TriCheck

and Cuff Inflation Meter

MEMORY

I.H.B. Symbol

Symbol

Heart Mark

Battery Indicator

AM / PM Mark

AC Adapter Jack

Battery Cover

Display

Air Socket

Average Pressure Settings

A&D Medical (Toll-Free): 1-888-726-9966

START Button

1.5V Batteries

(AA, LR6 or R6P)

Clock Display

Speaker

Button Button

SET Button

VOLUME

Button

Systolic Pressure

Diastolic Pressure

Pulse Rate

A&D blood pressure monitors are easy to use, accurate and digitally display full measurement readouts. Our technology is based on the "oscillometric method" – a noninvasive blood pressure determination. The term "oscillation" refers to any measure of vibrations caused by the aterial pulse. Our monitor examines the pulsatile pressure generated by the aterial wall as it expands and contracts against the cuff with each heartbeat.

The cuff is inflated until the artery is fully blocked. The inflation speed is maximized and the pressure level is optimized by the device. The monitor takes measurements while the cuff is both inflating and deflating. This results in a faster measurement providing greater comfort to the user.

BEFORE YOU START

You must install 4 type A (1.5 volt) batteries (alkaline batteries recommended), or use the AC Adapter (see page E-20 for using the Monitor with AC Adapter) and attach the cuff to the monitor before using it. To install batteries (or replace them if the "Low Battery" symbol appears on display), proceed as follows:

1. Remove battery compartment cover by gently pushing down on arrow and sliding cover forward.

2. Put in bottom row of batteries first. Place the batteries in compartment with positive (+) and negative (–) terminals matching those indicated in the compartment. Be sure batteries make contact with compartment terminals.

3. Replace cover by sliding it into the compartment and gently pressing into place.

NOTE: Rechargeable batteries are not recommended

for use with this monitor.

NOTE: Please dispose of batteries following local

regulations.

In Canada - Auto Control Medical (Toll-Free): 1-800-461-0991

Step 1

Step 3

Step 2

E-8

SELECTING THE CORRECT CUFF SIZE

22 - 32cm

8.6" - 12.6"

1 - 2cm

(0.5'')

1 2

ADJUSTING THE CLOCK

Using the correct cuff size is important for an accurate reading. A cuff that is too large will produce a reading that is lower than the correct blood pressure; a cuff that is too small will produce a reading that is higher than the correct blood pressure. With your arm hanging at the side of your body, measure the circumference of your upper arm at the midpoint between the shoulder and elbow.

6.3

Using the right sized cuff is essential to an accurate measurement. Our unique cuff is designed to accommodate a wide range of arm sizes, from 9 – 14.6" (23 – 37 cm). The SlimFit™ cuff is contoured to provide you with a quick and comfortable fit. Just slide the cuff onto your upper arm and secure – it’s that simple! For more detail, please read the section Taking Your Blood Pressure (see pg. E-12).

If your arm circumference is greater than 14.6" (37 cm) or smaller than 9" (23 cm), you will need to purchase a different size cuff than the one that is included in this box. Please call A&D Medical at 1-888-726-9966 (in Canada please call 1-800-461-0991) for more information on our alternate cuff sizes.

1 2 3

1 - 2cm

(0.5'')

SlimFit™ Small Cuﬀ

SlimFit™ Medium Cuﬀ

SlimFit™ Large Cuﬀ

SmoothFit™ Cuﬀ

BRAND

The UA-1030T blood pressure monitor has a built-in clock that gives you the time and date and can tell you when a blood pressure reading stored in memory was taken. We recommend that you adjust the clock prior to use. To adjust the clock, follow these simple steps:

1. Press the clock button

located to the right of the display.

2. Use the arrow buttons to set the year.

3. After reaching the desired year, press the clock button again.

4. Repeat the process for the month, day and hour.

5. The next setting will be for pressure.

ADJUSTING THE PRESSURE

1. After setting the year, month, day and hour, the next mode is the pressure setting.

2. Default is , which stands for automatic.

3. For even more rapid readings, you can adjust the default to about 30 mmHg or more above your expected systolic pressure.

4. Use the arrow buttons to set the pressure.

5. After reaching the desired pressure, press the clock button again.

6. The next setting will be for TriCheck™ Mode.

E-9

A&D Medical (Toll-Free): 1-888-726-9966

In Canada - Auto Control Medical (Toll-Free): 1-800-461-0991

E-10

TRICHECK™ MODE TAKING YOUR BLOOD PRESSURE

The UA-1030T blood pressure monitor has an optional feature to automatically take three consecutive readings one minute apart and then provide you with the average. This complies with the American Heart Association's recommended measuring method.

1. After setting the year, month, day, hour and pressure, the next mode is the TriCheck™ Mode.

2. Default is off.

3. To turn on, use the arrow

4. To turn off again, use the arrow

5. After reaching the desired setting, press the clock

6. This will end your settings session.

7. To adjust any values, push the clock

buttons.

button again.

button and begin again.

TIPS FOR BLOOD PRESSURE MONITORING:

Relax for several moments before measurement.

☞

Do not smoke or ingest caffeine at least 30 minutes prior to measurement.

☞

Remove constricting clothing and place cuff on bare arm.

☞

Unless your physician recommends otherwise, use left arm to measure

☞

pressure. Do not talk during measurement.

☞

Do not cross legs and keep your feet flat on floor during measurement.

☞

NOW YOU ARE READY. FOLLOW THESE SIMPLE STEPS:

1. Sit comfortably with your left arm resting on a flat surface so that the center of your upper arm is at the same height as your heart.

2. Lay left arm on the table, palm up and wrap the cuff around the upper arm, about 0.5" (1-2 cm) above the inside of the elbow, as shown, Place the cuff directly against the skin, as clothing my cause a faint pulse, and result in a measurement error.

3. Make sure cuff is aligned at heart level

Cuff

Artery position mark

At heart level

0.5” or 1-2 cm

Air Hose

E-11

A&D Medical (Toll-Free): 1-888-726-9966

In Canada - Auto Control Medical (Toll-Free): 1-800-461-0991

E-12

TAKING YOUR BLOOD PRESSURE MEASUREMENT USING TRICHECK

5. Press the segments are displayed. Zero (0) is displayed blinking briefly. The display changes, as indicated in the figure at the right, as the measurement

START

button. All of the display

All of the display

segments displayed

Press

begins. The cuff starts to inflate. It is normal for the cuff to feel very tight. A pressure bar indicator is displayed, on the left edge of the display, during the inflation.

Note: If you wish to stop inflation at any time, press the

button again.

6. When inflation is complete, deflation starts automatically and

blinks, indicating that the

START

Zero display

Starts inflation

Pressurizing

measurement is in progress. Once the pulse is detected, the mark blinks with each pulse beat.

Note: If an appropriate pressure is not obtained, the device

starts to inflate again automatically. To avoid re-inflation, see “Measurement with the SET Pressure” on the next page.

7. When the measurement is complete, the systolic and diastolic pressure readings and pulse

Measurement

in progress

rate are displayed. The device announces the measurement results. The cuff exhausts the remaining air and deflates completely.

8. Press the

START

button to turn the device off. After one minute of non-operation, the device will turn off automatically.

9. The reading is then stored into memory. See page

Systolic pressure

Diastolic pressure WHO classification

Pulse rate

Exhausts remaining

air automatically

E-18 for more details about the memory function.

10. Remove cuff and make a note of blood pressure and pulse rate on the chart in the back of this manual, indicating date and time of measurement. Additional logbook charts can be downloaded and printed for free at www.andmedical.com or in Canada at www.autocontrol.com. We advise that you record the date and time after each measurement becaue an accurate blood pressure history relies not on single or sporadic readings, but on a pattern over time.

START

1. Press the All of the display segments are displayed.

START

button.

At heart level

Zero (0) is displayed blinking briefly and the

START

first measurement starts.

2. When the measurement is complete, the systolic and diastolic pressure readings and pulse rate are displayed, then a one-minute countdown starts for the second measurement.

Press

All of the display segments displayed

First measurement

3. After one minute, the second measurement starts.

4. When the measurement is complete, the average readings of the first and second measurements are displayed, then a one-minute countdown starts for the third

One minute after

Results of the first measurement

Second measurement

measurement.

5. After one minute, the third measurement starts.

6. When the measurement is complete, the average readings of the three measurements are displayed and stored in memory.

Notes:

One minute after

Average of the first and second measurements

Third measurement

During the measurement, the TriCheck

symbol is displayed.

To cancel the measurement, press the START

button. In this case, no data is stored in

Average of the three measurements

memory.

When the cuff fit error symbol appears during the first measurement, cancel

the measurement, reapply the cuff correctly and start a new measurement.

After measurement, the average data of the three measurements is stored in

memory. No data will be stored, when canceling the measurements, or before completion of the third measurement.

E-13

A&D Medical (Toll-Free): 1-888-726-9966

In Canada - Auto Control Medical (Toll-Free): 1-800-461-0991

E-14

MEASUREMENT WITH SET PRESSURE WHAT IS AN IRREGULAR HEARTBEAT

Turn off

TriCheck setting mode

1932-1AIc UA787EXC•06 illust•03,12p symbols.FH7

The UA-1030T is designed to detect the pulse and to inflate the cuff to a systolic pressure level automatically. If re-inflation occurs repeatedly, use the following

methods. During the blood pressure measurement, re-inflation may occur. A fixed pressure

value can be set to avoid re-inflation.

1. At step 6 of the clock adjustment procedure (see page E-10), press the

SET

button to go to the pressure setting

mode. The current setting blinks.

2. Press the or button to select a pressure value about 30 mmHg or more above your expected systolic pressure from the following.

AUTO

3. Press the

Press the

: Automatic pressurization (default value)

180

: Pressure value of 180 mmHg (fixed)

210

: Pressure value of 210 mmHg (fixed)

240

: Pressure value of 240 mmHg (fixed)

SET

button to go to the TriCheck setting mode.

START

button to turn the device off. After three minutes of

Turn off

non-operation, the device will turn off automatically. The next measurement will be performed with the new pressure value.

MEASUREMENT WITH DESIRED SYSTOLIC PRESSURE

Use this method when re-inflation occurs repeatedly even if the pressure value is

240

set to

in the procedure above or when the results are not displayed even if

the pressure decreases to 20 mmHg or less.

1. Place the cuff on the arm (preferably the left arm).

2. Press and hold the

START

button until a number about 30 to 40 mmHg higher than your expected systolic pressure appears.

3. When the desired number is reached, release the

START

button to start measurement. Continue to measure your blood pressure as described on the previous page.

E-15

A&D Medical (Toll-Free): 1-888-726-9966

At heart level

Press and hold the button

Release the button

at the desired

systolic pressure

Refer to previous page

for measurement

TriCheck setting mode

START

The UA-1030T blood pressure monitor provides a blood pressure and pulse rate measurement even when an irregular heartbeat occurs. The Irregular Heartbeat symbol

will appear in the display window in the event an Irregular Heartbeat has occured during measurement. An irregular heartbeat is defined as a heartbeat that varies by 25% from the average of all heartbeat intervals during the blood pressure measurement. It is important that you relax, remain still and refrain from talking during measurements.

Note: We recommend contacting your physician if you see this symbol frequently.

ABOUT CUFF INFLATION METER

The Cuff Inflation Meter is located on the left side of the display screen to tell you when the blood pressure monitor is inflating and deflating the cuff. The Cuff Inflation Meter moves up during inflation and moves down during deflation.

Inflation in Progress Inflation Complete

In Canada - Auto Control Medical (Toll-Free): 1-800-461-0991

Deflation/Measurement

in Progress

E-16

ABOUT THE PRESSURE RATING INDICATOR™ ABOUT MEMORY

JNC7 Classification Indicator

Hypertension Stage 2 Hypertension Stage 2 Hypertension Stage 1 Prehypertension Prehypertension Normal

JNC7 Classification Indicator

Stage 2 Hypertension Stage 1 Hypertension Prehypertension Normal

Example

Stage 2

Hypertension

The Pressure Rating Indicator™ is a feature which provides a snapshot of your blood pressure classification based on your measurements. This will let you quickly know what your blood pressure readings mean. Each segment of the bar indicator corresponds to the Seventh Report of the Joint National Committee (JNC7) on Prevention, Evaluation and Treatment of High Blood Pressure from the National Heart, Lung and Blood Institute - May 2003. For a more detailed look at this blood pressure classification, please refer to “Assessing High Blood Pressure” on page E-22.

: The indicator displays a segment, based on the current measurement,

corresponding to the JNC7 Classification.

NOTE: Due to other risk factors (e.g. diabetes, obesity, smoking, etc.) in addition to your blood

pressure measurement, the Pressure Rating Indicator is approximate. Please consult with your physician for interpretation and diagnosis of your blood pressure measurements.

NOTE: Residents outside of the United States (e.g.. Canada and Mexico) should refer to the WHO

Classification Table on page E-22 for assessment of their blood pressure measurement.

E-17

Example

Hypertension

A&D Medical (Toll-Free): 1-888-726-9966

Stage 2 Hypertension Stage 1 Hypertension Prehypertension Normal

Stage 2

Note: This device stores the last 90 measurements in memory. The device announces the memory

data values as they are displayed.

1. Press the or button. The average of all

measurements and the number of data are displayed. (If no data, “0” is displayed. Press the

, or

START

button to turn the

device off.)

2. Each time the

button (or the button to display the data in the reverse order) is pressed, the memory data is displayed as follows.

Average of all AM (morning) measurements

Press or

Average of all the data

Average of AM data

Average systolic Average diastolic Average pulse

taken between 4:00 and 9:59. (In the example, 10 measurements. If no data, “--” is displayed.)

Average of all PM (evening) measurements

Average of PM data

Average systolic Average diastolic Average pulse

taken between 18:00 and 1:59. (In the example, 9 measurements. If no data, “--” is displayed.)

Most recent data (See No. 35). Three

Most recent data

Systolic Diastolic Pulse

seconds after the data number display, the measurement data is displayed.

Last data (No.1). Three seconds after the

data number display, the measurement data is displayed.

Last data (Oldest)

Systolic Diastolic Pulse

3. After the last data is displayed, press the button to return the average display of all measurements.

4. Press the

START

button to turn the device off. After one minute of

non-operation, the device will turn off automatically.

In Canada - Auto Control Medical (Toll-Free): 1-800-461-0991

E-18

ADJUSTING THE SPEAKER VOLUME USING THE MONITOR WITH AC ADAPTER

Volume off

The current setting appears

or to change the volume

1. Press the

VOLUME

button to enter the volume adjustment mode. Six stages of volume, which are represented by bars, and OFF are available.

2. Press the or press the

button to increase the volume,

button to decrease the

volume.

3. Press the

START

button to turn the device off. After three minutes of non-operation, the device will turn off automatically.

SELECTING THE LANGUAGE

1. In the volume adjustment mode, press the

VOLUME

button to enter the language selection

mode. The current setting appears.

2. Press the

or button to select a language

from the following. L1: English (default value)

L2: French L3: Spanish

3. Press the

START

button to turn the device off. After three minutes of non-operation, the device will turn off automatically.

High

Low

The current setting appears

or to change the volume

press

The current setting appears

or to change the language

Volume off

The UA-1030T has an AC adapter jack to allow you to supply power from an outlet in your home. We recommend you only use the exclusive AC adapter to avoid potential damage to the monitor. Please contact A&D Medical at 1-888-726-9966 or if you are in Canada contact AutoControl at 1-800-461-0991, if you would like to purchase an additional AC adapter.

CONNECTING THE AC ADAPTER TO THE MONITOR:

1. Gently insert the AC adapter plug into a 120V AC outlet.

2. Connect the AC adapter plug into the jack on the back of the monitor.

DISCONNECTING THE AC ADAPTER FROM THE MONITOR:

1. Turn the unit off by pressing the START button.

2. Disconnect the plug from the jack of the monitor quickly.

3. Gently remove the AC adapter from the outlet.

NOTE: If monitor has batteries and an AC adapter connected, the measurements stored

in memory may be lost if AC adapter is unplugged from the wall first. To ensure that measurements remain in memory, make sure the unit is off and that the jack plugged into the monitor is removed quickly before unplugging adapter from the wall.

Jack

E-19

A&D Medical (Toll-Free): 1-888-726-9966

Plug

In Canada - Auto Control Medical (Toll-Free): 1-800-461-0991

AC Adapter

TB-233

E-20

ABOUT BLOOD PRESSURE

WHAT IS BLOOD PRESSURE?

Blood pressure is the force exerted by blood against the walls of the arteries. Systolic pressure occurs when the heart contracts; diastolic pressure occurs when the heart expands. Blood pressure is measured in millimeters of mercury (mmHg).

WHAT AFFECTS BLOOD PRESSURE?

Blood pressure is affected by many factors: age, weight, time of day, activity level, climate, altitude and season. Certain activities can significantly alter one’s blood pressure. Walking will likely raise an individual’s blood pressure. Sleeping will likely decrease blood pressure. Not relaxing for several moments before measurements can influence readings as well.

In addition to these factors, beverages containing caffeine or alcohol, certain medications, emotional stress and even tight-fitting clothes can make a difference in the readings.

WHAT CAUSES VARIATIONS IN BLOOD PRESSURE?

An individual’s blood pressure varies greatly from day to day and season to season. For hypersensitive individuals, these variations are even more pronounced. Normally, blood pressure rises during work or play and falls to its lowest levels during sleep.

ASSESSING HIGH BLOOD PRESSURE FOR ADULTS

The following standards for assessing high blood pressure (without regard to age or gender) have been established as a guideline. Please note that other risk factors (e.g. diabetes, obesity, smoking, etc.) need to be taken into consideration and may affect these figures. Consult with your physician for an accurate assessment.

JNC7 Classification Table – for adults within the U.S

BP Classification Systolic (mmHg) Diastolic (mmHg)

Normal less than 120 and less than 80 Prehypertension 120-139 or 80-89 Stage 1 Hypertension 140-159 or 90-99 Stage 2 Hypertension 160 or 100

SOURCE: The Seventh Report of the Joint National Committee on Prevention, Evaluation

and Treatment of High Blood Pressure for adults. National Heart, Lung and Blood Institute - May 2003.

greater than or equal to

WHO Classification Table – for adults outside of the U.S. (e.g. Canada, Mexico)

BP Classification Systolic (mmHg) Diastolic (mmHg)

greater than or equal to

Optimal less than 120 and less than 80 Normal less than 130 or less than

85 High-Normal 130-139 or 85-89 Grade 1 Hypertension 140-159 or 90-99 Grade 2 Hypertension 160-179 or 100-109 Grade 3 Hypertension 180 or 110

SOURCE: Standards to assess high blood pressure, without regard to age or gender, have

been established by the World Health Organization (WHO).

greater than or equal to

E-21

A&D Medical (Toll-Free): 1-888-726-9966

In Canada - Auto Control Medical (Toll-Free): 1-800-461-0991

E-22

ABOUT BLOOD PRESSURE

WHAT IS HYPERTENSION?

Hypertension (high blood pressure) is the diagnosis given when readings consistently rise above normal. It is well known that hypertension can lead to stroke, heart attack or other illness if left untreated. Referred to as a “silent killer” because it does not always produce symptoms that alert you to the problem, hypertension is treatable when diagnosed early.

CAN HYPERTENSION BE CONTROLLED?

In many individuals, hypertension can be controlled by altering lifestyle and minimizing stress, and by appropriate medication prescribed and monitored by your doctor. The American Heart Association recommends the following lifestyle suggestions to prevent or control hypertension:

Don’t smoke. Have regular Reduce salt and fat intake. physical checkups. Maintain proper weight. Monitor your blood Exercise routinely. pressure at periodic

intervals.

WHY MEASURE BLOOD PRESSURE AT HOME?

It is now well known that, for many individuals, blood pressure readings taken in a doctor’s office or hospital setting might be elevated as a result of apprehension and anxiety. This response is commonly called “white coat hypertension.”

In any case, self-measurement at home supplements your doctor’s readings and provides a more accurate, complete blood pressure history. In addition, clinical studies have shown that the detection and treatment of hypertension is improved when patients both consult their physicians and monitor their own blood pressure at home.

ANSWERS TO WHY YOUR READINGS ARE DIFFERENT BETWEEN HOME AND AT THE DOCTOR’S OFFICE

Why are my readings different between home and at a doctor’s office?

Your blood pressure readings taken in a doctor’s office or hospital setting may be elevated as a result of apprehension and anxiety. This response is known as white coat hypertension.

When I bring my monitor to a doctor’s office, why do I get a different measurement from my monitor to that taken by a doctor or nurse?

The healthcare professional may be using a different sized cuff. The size of the bladder inside the cuff is critical for the accuracy of the measurement. This may give you a different reading. A cuff too large will produce a reading that is lower than the correct blood pressure; a cuff that is too small will produce a reading that is higher than the correct blood pressure. There may also be other factors that can cause the difference in measurements.

KEYS TO SUCCESSFUL MONITORING:

Blood pressure fluctuates throughout the day. We recommend that you are consistent in your daily measurement routine:

• Measure at the same time every day.

• Sit in the same chair/position.

• Do not cross legs and keep your feet flat on the floor.

• Relax for several minutes before measurement.

• Use the correct cuff size to get an accurate reading.

• Sit still during measurement – no talking, eating or sudden movements.

• Record your measurement in a logbook.

E-23

A&D Medical (Toll-Free): 1-888-726-9966

In Canada - Auto Control Medical (Toll-Free): 1-800-461-0991

E-24

ABOUT BLOOD PRESSURE TROUBLESHOOTING

ESTABLISHING BASELINE MEASUREMENTS

The most important method to get an accurate blood pressure measurement is consistency. To get the most benefit out of your monitor, it is important to establish a “baseline measurement.” This helps build a foundation of measurements that you can use to compare against future readings. To build this baseline measurement, devote two weeks for consistent blood pressure monitoring. This involves doing everything the same way when you measure (e.g. measuring during the same time of day, in the same location, sitting in the same chair, using the same cuff, etc.). Once you establish your baseline measurement, you can start evaluating if your measurement has been affected based on things like lifestyle changes or medication treatment.

HOW DO I RECORD MY BLOOD PRESSURE?

Blood pressure readings are typically recorded with the systolic pressure written first, followed by a slash mark and the diastolic pressure. For example, 120 mmHg systolic and 80 mmHg diastolic measurements are written as 120/80. Pulse is simply written with the letter “P” followed by the pulse rate—P 72, for example. Please see the back of the manual for the blood pressure tracking record.

CUSTOMER SUPPORT TOOLS ONLINE

Additional tools are available on www.andmedical.com to help you get the most out of your blood pressure monitoring. These include:

• Large Print Instruction Manuals

• Animated Operating Instructions

• Additional Logbook Sheets

Problem Probable Cause

Nothing appears in the display, after I press the START button.

The cuff does not inflate.

The unit does not measure. Readings are too high or too low.

The value is different from that measured at a clinic or doctor’s office.

Batteries are drained.

Battery terminals are not in the correct position.

Battery voltage is too low. Low battery symbol blinks. [If the batteries are drained completely, the mark does not appear.]

The cuff is not fastened properly.

You moved your arm or body during the measurement.

The cuff position is not correct.

You are using the wrong size cuff.

Taking too many readings on the same arm in a short period of time.

The healthcare professional may be using a different sized cuff.

Your measurements may be elevated by white coat hypertension

Corrective Action

Replace all batteries with new ones. Alkaline batteries recommended.

Reinstall the batteries with negative and positive terminals matching those indicated in the battery compartment.

Replace all batteries with new ones. Alkaline batteries recommended.

Fasten the cuff correctly.

Make sure you remain very still and quiet during the measurement.

Sit comfortably and still. Make sure the cuff is at the same level as your heart.

See Pg. E-9 "Selecting the Correct Cuff."

Relax several minutes before each measurement.

See Pg. E-24 "Answers to Why Your Readings Are Different Between Home and the Doctor’s Office."

See Pg. E-23 "Why Measure Blood Pressure at Home."

E-25

A&D Medical (Toll-Free): 1-888-726-9966

NOTE: If the actions described above do not solve the problem, call 1-888-726-9966.

Do not attempt to repair the device yourself.

In Canada - Auto Control Medical (Toll-Free): 1-800-461-0991

E-26

SPECIFICATIONS CONTACT INFORMATION

R6(AA)

2010

R6(AA)

2010

Model

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .UA-1030T / UA-1030TCN (Canada)

Type

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Oscillometric

Display

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .Digital character height

Pressure (20.0 mm)/Pulse (11.5 mm) displayed simultaneously

Memory

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .90 readings

Measurement range

. . . . . . . . . . . . . . . . . . . .Pressure: 0 - 299 mmHg

Systolic pressure: 60 - 279 mmHg Diastolic pressure: 40 - 200 mmHg Pulse: 40 - 180 beats per minute

Accuracy

. . . . . . . . . . . . . . . . . . . . . . . . . . . .Pressure: ± 3 mmHg or ± 2%, whichever is

greater, Pulse: ± 5%

Power source

. . . . . . . . . . . . . . . . . . . . . . . . .4 x 1.5 volt batteries (AA, LR6 or R6P)

or 120 volt AC adapter (TB-233)

Classification Clinical test EMC Recommended operating environment

. . . . . . . . . . . . . . . . . . . . . . . . .Type BF

. . . . . . . . . . . . . . . . . . . . . . . . . .According to ANSI / AAMI SP-10 1992

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .IEC 60601-1-2: 2007

. . . . . .50ºF to 104ºF (10ºC to 40ºC)

Less than 85% relative humidity

Recommended storage environment

Dimensions

. . . . . . . . . . . . . . . . . . . . . . . . . .Length: 4.1” (105 mm)

. . . . . . . .-4ºF to 140ºF (-20ºC to 60ºC)

Less than 95% relative humidity

Width: 5.5” (140 mm) Height: 2.4” (60 mm)

Weight

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10.6 oz. (285 g) without batteries

(U.S.A.)

0366

Blood pressure measurements determined by the UA-1030T are equivalent to those obtained by a trained observer using the cuff/stethoscope auscultation method within the limits prescribed by the American National Standards Institute for electronic or automated sphygmomanometers.

Our products are designed and manufactured using the latest scientific and technological methods, and offer accurate, easy to use, home monitoring and treatment options. Our full product line includes:

■■■ Digital■Blood Pressure Monitors

■■■ Manual■Blood Pressure Monitors

■■■ Blood■Pressure Cuffs

■■■ Stethoscopes

■■■ Personal■Health Scales

■■■ Digital■Thermometers

■■■ Activity■Monitors

■■■ Wireless■Products

This blood pressure monitor and cuff carries different warranties in different countries of purchase. Please see below for warranty length and contact information where you purchased this product.

In the United States of America:

5 year warranty A&D Medical A division of A&D Engineering, Inc. 1756 Automation Parkway San Jose, CA 95131 Toll-Free: 1-888-726-9966 www.andmedical.com

In Canada:

7 year warranty Auto Control Medical 6695 Millcreek Drive, Unit 6 Mississauga, Ontario L5N 5R8 Canada Toll-Free: 1-800-461-0991

In Latin America:

No warranty A&D Medical A division of A&D Engineering, Inc. 1756 Automation Parkway San Jose, CA 95131 Toll-Free: 1-888-726-9966 www.andmedical.com

All other countries:

Various warranties - see packaging A&D Company, Limited 1-243 Asahi, Kitamoto-shi, Saitama 364-8585 Japan [81] (48) 593-1119 www.aandd.jp

www.autocontrol.com

E-27

A&D Medical (Toll-Free): 1-888-726-9966

In Canada - Auto Control Medical (Toll-Free): 1-800-461-0991

E-28

+ 34 hidden pages

A and D UA-1030 User Manual [es]

Specifications and Main Features

Frequently Asked Questions

User Manual