Multi-Touch Panel PC ACP-5215
ACP-5215
21.5” Fanless Multi-Touch
Panel PC
®
Intel
CoreTM i7/i5/ P4500
Processor
High Brightness
ACP-5215 Manual 3rd Ed
June 2012
Multi-Touch Panel PC ACP-5215
Copyright Notice
This document is copyrighted, 2012. All rights are reserved. The
original manufacturer reserves the right to make improvements to
the products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated, or
transmitted in any form or by any means without the prior written
permission of the original manufacturer. Information provided in this
manual is intended to be accurate and reliable. However, the
original manufacturer assumes no responsibility for its use, nor for
any infringements upon the rights of third parties, which may result
from its use.
The material in this document is for product information only and is
subject to change without notice. While reasonable efforts have
been made in the preparation of this document to assure its
accuracy, AAEON, assumes no liabilities resulting from errors or
omissions in this document, or from the use of the information
contained herein.
AAEON reserves the right to make changes in the product design
without notice to its users.
i
Multi-Touch Panel PC ACP-5215
Acknowledgments
Intel
Microsoft
®
, CoreTM are registered trademarks of Intel® Corporation.
®
Windows is a registered trademark of Microsoft®
Corporation.
RTL is a trademark of Realtek Semi-Conductor Co., Ltd.
C&T is a trademark of Chips and Technologies, Inc.
UMC is a trademark of United Microelectronics Corporation.
ITE is a trademark of Integrated Technology Express, Inc.
All other product names or trademarks are properties of their
respective owners.
ii
Multi-Touch Panel PC ACP-5215
Packing List
Before you begin installing your Panel PC, please make sure
that the following items have been shipped:
ACP-5215 Infotainment Multi-Touch Panel PC
HDD screws
Product DVD
Contains User’s Manual (in PDF format), Drivers and
Utilities
If any of these items are missing or damaged, you should cont act y our
distributor or sales representative immediately.
iii
Multi-Touch Panel PC ACP-5215
Safety & Warranty
1. Read these safety instructions carefully.
2. Keep this user's manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Do
not use liquid or spray detergents for cleaning. Use a damp cl oth.
4. For pluggable equipment, the power outlet must be installed near
the equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation.
Dropping it or letting it fall could cause damage.
7. The openings on the enclosure are for air convection. Protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before
connecting the equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not
place anything over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the
power source to avoid damage by transient over-voltage.
12. Never pour any liquid into an opening. This could cause fire or
electrical shock.
13. Never open the equipment. For safety reasons, only qualified
service personnel should open the equipment.
iv
Multi-Touch Panel PC ACP-5215
14. If any of the following situations arises, get the equipment
checked by service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipme nt does not work well, or yo u cannot get it to
work according to the user’s manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED
ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS
BELOW -20° C (-4°F) OR ABOVE 70° C (158° F). IT MAY
DAMAGE THE EQUIPMENT
16. External equipment intended for connection to signal input/output
or other connectors, shall comply with relevant UL / IEC standard
(e.g. UL 1950 for IT equipment and UL 60601-1 / IEC 60601 series
for systems – shall comply with the standard IEC 60601-1-1,
Safety requirements for medical electrical systems. Equipment
not complying with UL 60601-1 shall be kept outside the patient
environment, as defined in the standard.
17. When the temperature of CPU is higher than 35°C, the frequency
of CPU will be adjusted automatically. For example, if the
temperature of Intel Core i7 is 40°C, the frequency of the CP U will
be between 1.8~1.3 GHz.
.
Caution:
It may cause the danger of explosion if battery is incorrectly
replaced. Replace only with same or equivalent type
recommended by the manufacturer.
v
Multi-Touch Panel PC ACP-5215
Classification
1. Degree of production against electric shock: not classified
2. Degree of protection against the ingress of water: IPX1
3. Equipment not suitable for use in the presence of a flammable
anesthetic mixture with air or with oxygen or nitrous oxide.
4. Mode of operation: Continuous
5. Type of protection against electric shock: Class I equipment
vi
Multi-Touch Panel PC ACP-5215
FCC
This device complies with Part 15 FCC Rules.
Operation is subject to the following two
conditions: (1) this device may not cause
harmful interference, and (2) this device
must accept any interference received
including interference that may cause
undesired operation.
vii
Multi-Touch Panel PC ACP-5215
UL Module Description
ACP-5215 AC modules are developed to
suitable for the Classification Mark
requirement
viii
Multi-Touch Panel PC ACP-5215
Safety Symbol Description
The following safety symbols are further explanations for your
reference.
Medical equipment with respect to electric
shock, fire and mechanical hazards only in
accordance with UL 60601-1, and
CAN/CSA C22.2 NO. 601.1
Attention, consult ACCOMPANYING
DOCUMENTS.
Ground wire
Protective Ground wire.
Medical equipment with respect to electric
shock, fire and mechanical hazards only in
accordance with UL 60601-1, and
CAN/CSA C22.2 NO. 601.1
ix
Multi-Touch Panel PC ACP-5215
Below Table for China RoHS Requirements
产品中有毒有害物质或元素名称及含量
AAEON Panel PC/ Workstation
有毒有害物质或元素
部件名称
印刷电路板
及其电子组件
外部信号
连接器及线材
外壳 × ○ ○ ○ ○ ○
中央处理器
与内存
硬盘 × ○ ○ ○ ○ ○
液晶模块 × ○ ○ ○ ○ ○
光驱 × ○ ○ ○ ○ ○
触控模块 × ○ ○ ○ ○ ○
电源 × ○ ○ ○ ○ ○
O：表示该有毒有害物质在该部件所有均质材料中的含量均在
SJ/T 11363-2006 标准规定的限量要求以下。
X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出
SJ/T 11363-2006 标准规定的限量要求。
备注：
一、此产品所标示之环保使用期限，系指在一般正常使用状况下。
二、上述部件物质中央处理器、内存、硬盘、光驱、触控模块为选购品。
铅
(Pb)汞 (Hg)镉 (Cd)
× ○ ○ ○ ○ ○
× ○ ○ ○ ○ ○
× ○ ○ ○ ○ ○
六价铬
(Cr(VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
x
Multi-Touch Panel PC ACP-5215
Contents
Chapter 1 General Information
1.1 Introduction................................................................ 1-2
1.2 Features.................................................................... 1-3
1.3 Specification..............................................................1-4
1.4 General Information...................................................1-7
Chapter 2 Hardware Installation
2.1 Safety Precautions.................................................... 2-2
2.2 A Quick Tour of the ACP-5215.................................. 2-3
2.3 2.5” Hard Disk Drive (HDD) Installation ....................2-5
Chapter 3 AMI BIOS Setup
3.1 System Test and Initialization . ................................. 3-2
3.2 AMI BIOS Setup........................................................ 3-3
Chapter 4 Driver Installation
4.1 Installation................................................................. 4-3
Appendix A Programming the Watchdog Timer
A.1 Programming .........................................................A-2
A.2 ITE8781 Watchdog Timer Initial Program..............A-6
Appendix B I/O Information
B.1 I/O Address Map....................................................B-2
st
B.2 1
MB Memory Address Map ................................B-4
xi
Multi-Touch Panel PC ACP-5215
B.3 IRQ Mapping Chart ..............................................B-5
B.4 DMA Channel Assignments...................................B-5
Appendix C Miscellanea
C.1 General Cleaning Tips.......................................... C-2
C.2 Cleaning Tools...................................................... C-3
C.3 Scrap Computer Recycling ................................. C-5
C.4 Installing Accessories........................................... C-6
xii
Multi-Touch Panel PC ACP-5215
Information
Chapter
1
General
Chapter 1 General Information 1-1
Multi-Touch Panel PC ACP-5215
1.1 Introduction
The ACP-5215 is a Multi-Touch Infotainment Panel PC with
superior onboard Intel
®
Core™ i7/i5/P4500 processor-based
computer. It is a PC-based system with 21.5” Full HD (1920x1080)
Fanless TFT LCD display, integrated multimedia functions make
them the perfect platforms to build comprehensive lifestyle
computing applications.
The ACP-5215 includes all the features of a powerful computer into
a slim and attractive chassis. The ACP-5215 has 250 nits TFT
display with 1920x1080 resolution. This model equips two-point
Multi-Touch Window design and is easy to clean. Moreover, it is
IPX1 100% water-proof that can be installed in harsh environments.
Its front bezel is IP-65/NEMA4 for auxiliary water-proof protection.
In addition, the ACP-5215 deploys 7H hardness Anti-Scratch
Surface to avoid accidental damage.
The ACP-5215 supports one 2.5” SATA Hard Disk Drive and one
CompactFlash™ slot for the storage functions, and one Mini Card
expansion. Moreover, it supports Smart Card Reader, RFID, MSR,
Skype phone, and camera to fulfill the demands of versatile
applications.
Chapter 1 General Information 1-2
Multi-Touch Panel PC ACP-5215
1.2 Features
21.5” Full HD (1920x1080) Fanless TFT LCD Display
Easy-To-Clean: Multi-Touch Window Design (Two-Point)
Superior Intel
IP65 Front Bezel & IPx1 Back Chassis
Anti-Scratch Surface (7H Hardness)
Smart Card Reader/ RFID/ MSR/ Skype Phone/ Camera
®
Core™ i7/i5/P4500 Processor
Support
Chapter 1 General Information 1-3
Multi-Touch Panel PC ACP-5215
1.3 Specification
System
Processor Intel
®
Core™ i7/i5/P4500 Processor,
Core™ i7-620M, Core™i5-520M, P4500
System Memory DDR3 SODIMM x 1, Max. 4 GB
LCD / CRT Controller Integrated graphics in Intel
Ethernet 10/100/1000Base-TX, RJ-45 x 2
I/O Port USB2.0 x 6 (2 on side; 4 on rear)
®
QM57
RS-232 x 1
Line-out x 1
VGA x 1
Storage Disk Drive 2.5” SATA Hard Disk Drive/
CompactFlash™ slot (Internal)
Expansion Mini Card x 1
OS Support Windows
®
XP (T/S: Single point), Linux
Fedora (T/S: Single point), Windows®7
(T/S: Multi-point)
Mechanical
Construction IP65/ NEMA4 for plastic front bezel,
IPX1 for plastic chassis
Mounting VESA 100
Dimension 21.5”(W) x 13.7”(H) x 2.2”(D) (546mm x
Chapter 1 General Information 1-4
Multi-Touch Panel PC ACP-5215
348.1mm x 56mm)
Net Weight 17.38 lb (7.9 kg)
Gross Weight 22.44 lb (10.2 kg)
Environmental
Operating Temperature 32
Storage Temperature -4
Storage Humidity 10%~95% @ 40
Vibration 1 g rms/ 5-500Hz/ Random Operation
Shock 20 G peak acceleration (11 msec.
EMC CE/FCC Class A
o
F~104oF (0oC~40oC)
o
F~158oF (-20oC~70oC)
o
C, non-condensing
(HDD)
duration)
Power Supply
DC Input 70W DC 12V, with AC power adapter with
lock in package
LCD
Display Type 21.5” TFT-LCD, LED
Max. Resolution 1920 x 1080
Max. Colors 16.7 M colors (6/8-bit for R, G, B)
Luminance (cd/m
Viewing Angle 170º (H), 160º (V)
Backlight LED
Chapter 1 General Information 1-5
2
) 250 cd/m2
Multi-Touch Panel PC ACP-5215
Backlight MTBF (Hours) 50,000
Touchscreen
Type Projected Capacitive Multi-Touch
(Windows® 7)
Light Transmission 90%
Chapter 1 General Information 1-6
Multi-Touch Panel PC ACP-5215
1.4 General Information
RFID
1.3M Camera
Brightness+
Brightness-
Volume-
Volume+
LCD On/Off
VESA 100
2W
Speaker
2W
Speaker
Chapter 1 General Information 1-7
Multi-Touch Panel PC ACP-5215
COM x 1
Line-out
Power Input
Antenna
Power Switch
VGA
LAN x 2
USB x 4
Antenna
USB x 2
Smart Card
Reader
Chapter 1 General Information 1-8
Multi-Touch Panel PC ACP-5215
Chapter
2
H
Chapter 2 Hardware Installation 2-1
ardware
Inst
allation
Multi-Touch Panel PC ACP-5215
2.1 Safety Precautions
Always completely disconnect the power cord
from your board whenever you are working on
it. Do not make connections while the power is
on, because a sudden rush of power can
damage sensitive electronic components.
Always ground yourself to remove any static
charge before touching the board. Modern
electronic devices are very sensitive to static
electric charges. Use a grounding wrist strap at
all times. Place all electronic components on a
static-dissipative surface or in a static-shielded
bag when they are not in the chassis
Chapter 2 Hardware Installation 2-2
Multi-Touch Panel PC ACP-5215
2.2 A Quick Tour of the ACP-5215
Mechanical Drawings
Front
Chapter 2 Hardware Installation 2-3
Multi-Touch Panel PC ACP-5215
Rear
I/O
Cable Cover (Optional)
Chapter 2 Hardware Installation 2-4
Multi-Touch Panel PC ACP-5215
Note 1: You may turn on the power by cutting and destroying the protective
cover as it shows below.
Note 2: The “Anti-Drop Kit” can help on preventing the cable drop from the
connector
Chapter 2 Hardware Installation 2-5
Multi-Touch Panel PC ACP-5215
2.3 2.5” Hard Disk Drive (HDD) Installation
Step 1: Unscrew the rear cover screws (15 screws)
Step 2: Remove EMI Cover (4 screws)
Chapter 2 Hardware Installation 2-6
Multi-Touch Panel PC ACP-5215
Step 3: Remove HDD Bracket (4 screws)
Step 4: Get the HDD and HDD Bracket ready
Chapter 2 Hardware Installation 2-7
Multi-Touch Panel PC ACP-5215
Step 5: Fasten the four screws to fix HDD Bracket and HDD
Step 6: Connect the SATA and power cables to the HDD and fasten the
four screws to fix the HDD Bracket
Chapter 2 Hardware Installation 2-8
Multi-Touch Panel PC ACP-5215
Chapter
3
AMI
BIOS Setup
Chapter 3 AMI BIOS Setup 3-1
Multi-Touch Panel PC ACP-5215
3.1 System Test and Initialization
These routines test and initialize board hardware. If the routines
encounter an error during the tests, you will either hear a few short
beeps or see an error message on the screen. There are two kinds
of errors: fatal and non-fatal. The system can usually continue the
boot up sequence with non-fatal errors.
System configuration verification
These routines check the current system configuration against the
values stored in the CMOS memory. If they do not match, the
program outputs an error message. You will then need to run the
BIOS setup program to set the configuration information in memory.
There are three situations in which you will need to change the
CMOS settings:
1. You are starting your system for the first time
2. You have changed the h ardware attached to your system
3. The CMOS memory has lost power and the configuration
information has been erased.
The ACP-5215 CMOS memory has an integral lithium battery
backup for data retention. However, you will need to replace the
complete unit when it finally runs down.
Chapter 3 AMI BIOS Setup 3-2
Multi-Touch Panel PC ACP-5215
3.2 AMI BIOS Setup
AMI BIOS ROM has a built-in Setup program that allows users to
modify the basic system configuration. This type of information is
stored in battery-backed CMOS RAM so that it retains the Setup
information when the power is turned off.
Entering Setup
Power on the computer and press <Del> or <F2> immediately. This
will allow you to enter Setup.
Main
Set the date, use tab to switch between date elements.
Advanced
Enable disable boot option for legacy network devices.
Chipset
host bridge parameters.
Boot
Enables/disable quiet boot option.
Security
Set setup administrator password.
Save&Exit
Exit system setup after saving the changes.
Chapter 3 AMI BIOS Setup 3-3
Multi-Touch Panel PC ACP-5215
Chapter
4
Driver
Inst
Chapter 4 Driver Installation 4-1
allation
Multi-Touch Panel PC ACP-5215
The ACP-5215 comes with an AutoRun DVD-ROM that contains all
drivers and utilities that can help you to install the driver
automatically.
Insert the driver DVD, the driver DVD-title will auto start and show
the installation guide. If not, please follow the sequence below to
install the drivers.
Follow the sequence below to install the drivers:
Step 1 – Install Chipset Driver
Step 2 – Install VGA Driver
Step 3 – Install LAN Driver
Step 4 – Install ME Driver
Step 5 – Install Audio Driver
Step 6 – Install Touch Driver (For Windows
®
XP only)
Step 7 – Install Smart Card Reader Driver (Optional)
Step 8 – Install WiFi Driver (Optional)
Please read instructions below for further detailed installations.
Chapter 4 Driver Installation 4-2
Multi-Touch Panel PC ACP-5215
4.1 Installation:
Insert the ACP-5215 DVD-ROM into the DVD-ROM drive. Then
install the drivers from Step 1 to Step 8 in order.
Step 1 – Install Chipset Driver
1. Click on the STEP1–CHIPSET folder and select the OS
folder your system is
2. Double click on the infinst_autol(9.1.1.1020).exe file
located in each OS folder
3. Follow the instructions that the window shows
4. The system will help you install the driver automatically
Step 2 – Install VGA Driver
1. Click on the STEP2–VGA folder and select the OS folder
your system is
2. Double click on the Setup.exe located in each OS folder
3. Follow the instructions that the window shows
4. The system will help you install the driver automatically
Note: If the OS is Windows® XP, you have to install the driver of dotNet
Framework first. Simply click on dotnetfx35.exe located in dotNet
Framwork folder.
Step 3 – Install LAN Driver
1. Click on the STEP3–LAN folder and select the OS folder
your system is
Chapter 4 Driver Installation 4-3
Multi-Touch Panel PC ACP-5215
2. Double click on the Auto
run.exe located in each OS
folder
3. Follow the instructions that the window shows
4. The system will help you install the driver automatically
Step 4 –Install ME Driver
1. Click on the STEP4–ME folder and select the OS folder
your system is
2. Double click on the Setup.exe file located in each OS
folder
3. Follow the instructions that the window shows
4. The system will help you install the driver automatically
Step 5 – Install Audio Driver
1. Click on the STEP5–Audio folder and select the OS
folder your system is
2. Double click on the SETUP.exe file located in each OS
folder
3. Follow the instructions that the window shows
4. The system will help you install the driver automatically
Step 6 – Install Touch Driver (For Windows® XP only)
1. Click on the STEP6–TOUCH folder and double click on
the ModifyDBArea file
2.
Follow the instructions that the window shows
Chapter 4 Driver Installation 4-4
Multi-Touch Panel PC ACP-5215
3. The system will help you install the driver automatically
Step 7 – Install Smart Card Reader Driver (Optional)
1. Click on the STEP7–SMART CARD READER folder and
select the OS folder your system is
2. Double click on the setup.exe located in each OS folder
3. Follow the instructions that the window shows
4. The system will help you install the driver automatically
Step 8 – Install WiFi Driver (Optional)
1. Click on the STEP8–WIFI folder and select the OS folder
your system is
2. Double click on the .exe located in each OS folder
3. Follow the instructions that the window shows
4. The system will help you install the driver automatically
Chapter 4 Driver Installation 4-5
Multi-Touch Panel PC ACP-5215
A
Appendix
Programming the
Watchdog Timer
Appendix A Programming the Watchdog Timer A-1
Multi-Touch Panel PC ACP-5215
A.1 Programming
ACP-5215 utilizes ITE 8781 chipset as its watchdog
timer controller. Below are the procedures to complete its
configuration and the AAEON initial watchdog timer
program is also attached based on which you can
develop customized programs to fit your application.
Configuring Sequence Description
After the hardware reset or power-on reset, the ITE 8781 enters the
normal mode with all logical devices disabled except
KBC. The initial state (enable bit ) of this logical device (KBC) is
determined by the state of pin 121 (DTR1#) at the falling edge of
the system reset during power-on reset.
Appendix A Programming the Watchdog Timer A-2
Multi-Touch Panel PC ACP-5215
There are three steps to complete the configuration setup: (1) Enter
the MB PnP Mode; (2) Modify the data of configuration re gisters; (3)
Exit the MB PnP Mode. Undesired result may occur if the MB PnP
Mode is not exited normally.
(1) Enter the MB PnP Mode
To enter the MB PnP Mode, four special I/O write operations are to
be performed during Wait for Key st ate. To ensure the initial st ate of
the key-check logic, it is necessary to p erform four write opera-tio ns
to the Special Address port (2EH). Two different enter keys are
provided to select configuration ports (2Eh/2Fh) of the next step.
(2) Modify the Data of the Regist ers
All configuration registers can be accessed after entering the MB
PnP Mode. Before accessing a selected register, the content of
Index 07h must be changed to the LDN to which the register
belongs, except some Global registers.
(3) Exit the MB PnP Mode
Set bit 1 of the configure control register (Index=02h) to 1 to exit the
MB PnP Mode.
Appendix A Programming the Watchdog Timer A-3
Multi-Touch Panel PC ACP-5215
WatchDog Ti mer Configuration Registers
Configure Control (Index=02h)
This register is write only. Its values are not sticky; that is to say, a
hardware reset will automatically clear the bits, and does not
require the software to clear them.
Watch Dog Timer 1, 2, 3 Control Register (Index=71h,81h,91h
Default=00h)
Appendix A Programming the Watchdog Timer A-4
Multi-Touch Panel PC ACP-5215
Watch Dog Timer 1, 2, 3 Configuration Register (Index=72h,
82h, 92h Default=001s0000b)
Watch Dog Timer 1,2,3 Time-Out Value (LSB) Register
(Index=73h,83h,93h, Default=38h)
Watch Dog Timer 1,2,3 Time-Out Value (MSB) Register
(Index=74h,84h,94h Default=00h)
Appendix A Programming the Watchdog Timer A-5
Multi-Touch Panel PC ACP-5215
A.2 ITE8781 Watchdog Timer Initial Program
.MODEL SMALL
.CODE
Main:
CALL Enter_Configuration_mode
CALL Check_Chip
mov cl, 7
call Set_Logic_Device
;time setting
mov cl, 10 ; 10 Sec
dec al
Watch_Dog_Setting:
;Timer setting
mov al, cl
mov cl, 73h
call Superio_Set_Reg
;Clear by keyboard or mouse interrupt
mov al, 0f0h
mov cl, 71h
call Superio_Set_Reg
;unit is second.
mov al, 0C0H
mov cl, 72h
call Superio_Set_Reg
Appendix A Programming the Watchdog Timer A-6
Multi-Touch Panel PC ACP-5215
; game port enable
mov cl, 9
call Set_Logic_Device
Initial_OK:
CALL Exit_Configuration_mode
MOV AH,4Ch
INT 21h
Enter_Configuration_Mode PROC NEAR
MOV SI,WORD PTR CS:[Offset Cfg_Port]
MOV DX,02Eh
MOV CX,04h
Init_1:
MOV AL,BYTE PTR CS:[SI]
OUT DX,AL
INC SI
LOOP Init_1
RET
Enter_Configuration_Mode ENDP
Exit_Configuration_Mode PROC NEAR
MOV AX,0202h
CALL Write_Configuratio n_Data
Appendix A Programming the Watchdog Timer A-7
Multi-Touch Panel PC ACP-5215
RET
Exit_Configuration_Mode ENDP
Check_Chip PROC NEAR
MOV AL,20h
CALL Read_Configuration_Data
CMP AL,87h
JNE Not_Initial
MOV AL,21h
CALL Read_Configuration_Data
CMP AL,81h
JNE Not_Initial
Need_Initial:
STC
RET
Not_Initial:
CLC
RET
Check_Chip ENDP
Read_Configuration_Data PROC NEAR
MOV DX,WORD PTR CS:[Cfg_Port+04h]
OUT DX,AL
Appendix A Programming the Watchdog Timer A-8
Multi-Touch Panel PC ACP-5215
MOV DX,WORD PTR CS:[Cfg_Port+06h]
IN AL,DX
RET
Read_Configuration_Data ENDP
Write_Configuration_Data PROC NEAR
MOV DX,WORD PTR CS:[Cfg_Port+04h]
OUT DX,AL
XCHG AL,AH
MOV DX,WORD PTR CS:[Cfg_Port+06h]
OUT DX,AL
RET
Write_Configuration_Data ENDP
Superio_Set_Reg proc near
push ax
MOV DX,WORD PTR CS:[Cfg_Port+04h]
mov al,cl
out dx,al
pop ax
inc dx
out dx,al
ret
Superio_Set_Reg endp.Set_Logic_Device proc near
Set_Logic_Device proc near
Appendix A Programming the Watchdog Timer A-9
Multi-Touch Panel PC ACP-5215
push ax
push cx
xchg al,cl
mov cl,07h
call Superio_Set_Reg
pop cx
pop ax
ret
Set_Logic_Device endp
;Select 02Eh->Index Port, 02Fh->Data Port
Cfg_Port DB 087h,001h,055h,055h
DW 02Eh,02Fh
END Main
Note: Interrupt level mapping
0Fh-Dh: not valid
0Ch: IRQ12
.
.
03h: IRQ3
02h: not valid
01h: IRQ1
00h: no interrupt selected
Appendix A Programming the Watchdog Timer A-10
Multi-Touch Panel PC ACP-5215
Appendix
B
I/O Information
Appendix B I/O Information B-1
Multi-Touch Panel PC ACP-5215
B.1 I/O Address Map
Appendix B I/O Information B-2
Multi-Touch Panel PC ACP-5215
Appendix B I/O Information B - 3
Multi-Touch Panel PC ACP-5215
st
B.2 1
MB Memory Address Map
Appendix B I/O Information B-4
Multi-Touch Panel PC ACP-5215
B.3 IRQ Mapping Chart
B.4 DMA Channel Assignments
Appendix B I/O Information B - 5
Multi-Touch Panel PC ACP-5215
A ppendix
C
Miscel
Appendix C Miscellanea C-1
lanea
Multi-Touch Panel PC ACP-5215
C.1 General Cleaning Tips
You may need the following precautions before you begin to clean
the computer. When you clean any single part or component for the
computer, please read and understand the details below fully.
1. Never spray or squirt the liquids directly onto any computer
component. If you need to clean the device, please rub it
with a piece of dry cloth.
2. Be cautious of the tiny removable comp onents when you
use a vacuum cleaner to absorb the dirt on the floor.
3. Turn the system off before you start to clean up the
component or computer.
4. Never drop the components inside the computer or get
circuit board damp or wet.
5. Be cautious of all kinds of cleaning solvents or chemicals
when you use it for the sake of cleaning. Some individuals
may be allergic to the ingredients.
6. Try not to put any food, drinks or cigarettes around the
computer.
Appendix C Miscellanea C-2
Multi-Touch Panel PC ACP-5215
C.2 Cleaning tools
Although many companies have created products to help improve
the process of cleaning your computer and peripherals users can
also use household items to clean their computers and peripherals.
Below is a listing of items you may need or want to use while
cleaning your computer or computer peripherals.
Keep in mind that some components in your computer may only be
able to be cleaned using a product designed for cleaning that
component, if this is the case it will be mentioned in the cleaning
tips.
Cloth - A piece of cloth is the best tool to use wh en rubbing
up a component. Although paper towels or tissues can be
used on most hardware as well, we still recommend you to
rub it with a piece of cloth.
Water or rubbing alcohol – You may moisten a piece of
cloth a bit with some water or rubbing alcohol and rub it on
the computer. Unknown solvents may be harmful to the
plastics parts.
Vacuum cleaner - Absorb the dust, dirt, hair, cigarette
particles, and other particles out of a computer can be one
of the best methods of cleaning a computer. Over time
these items can restrict the airflow in a computer and cause
circuitry to corrode.
Appendix C Miscellanea C-3
Multi-Touch Panel PC ACP-5215
Cotton swabs - Cotton swaps moistened with rubbing
alcohol or water are excellent tools for wiping hard to reach
areas in your keyboard, mouse, and other locations.
Foam swabs - Whenever possible it is better to use lint
free swabs such as foam swabs.
Note:
We strongly recommended that you should shut down the
system before you start to clean any single components.
Please follow the steps below.
1. Close all application programs
2. Close operating software
3. Turn off powe r switch
4. Remove all device
5. Pull out power cable
Appendix C Miscellanea C-4
Multi-Touch Panel PC ACP-5215
C.3 Scrap Computer Recycling
If the computer equipments need the maintenance or are beyond
repair, we strongly recommended that you should inform us as
soon as possible for the suitable solution. For the computers that
are no longer useful or work well, please contact with worldwide
distributors for recycling.
The worldwide distributors show on the following website:
http://www.aaeon.com/?TabIndex=Co
ntact&TabID=Distributors
Note:
Follow the national requirements to dispose unit
Appendix C Miscellanea C-5
Multi-Touch Panel PC ACP-5215
C.4 Installing Accessories
Skype Phone Installation
Step 1: Fasten the two screws(2-SELF TAPPING SCREWS) to fix the
Skype Bracket with the ACP-5215
Appendix C Miscellanea C-6
Multi-Touch Panel PC ACP-5215
MSR Installation
Step 1: Fasten the two screws (2-SELF TAPPING SCREWS) to fix the
MSR Bracket with the ACP-5215
Appendix C Miscellanea C-7
Multi-Touch Panel PC ACP-5215
Bar Code Scanner Installation
Step 1: Fasten the three screws to fix the Bar Code Scanner with the
backet
Appendix C Miscellanea C-8
Multi-Touch Panel PC ACP-5215
Multi-Touch Panel PC ACP-5215
Step 2: Fasten the two screws (2-SELF TAPPING SCREWS) to fix the Bar
Code Scanner with the ACP-5215
Appendix C Miscellanea C-9
Appendix C Miscellanea C-9
Loading...