Remote Touch Display ACD-515R
ACD-515R
15.6” WXGA Infotainment Touch Display
With Remote Display Technology
IP-65 Front Bezel
Multi-Touch Window Design (Two-Point)
ACD-515R Manual 1
st
Ed
April 2012
Remote Touch Display ACD-515R
Copyright Notice
This document is copyrighted, 2012. All rights are reserved. The
original manufacturer reserves the right to make improvements to
the products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated, or
transmitted in any form or by any means without the prior written
permission of the original manufacturer. Information provided in this
manual is intended to be accurate and reliable. However, the
original manufacturer assumes no responsibility for its use, nor for
any infringements upon the rights of third parties, which may result
from its use.
The material in this document is for product information only and is
subject to change without notice. While reasonable efforts have
been made in the preparation of this document to assure its
accuracy, AAEON, assumes no liabilities resulting from errors or
omissions in this document, or from the use of the information
contained herein.
AAEON reserves the right to make changes in the product design
without notice to its users.
i
Remote Touch Display ACD-515R
Acknowledgments
Intel
IBM, PC/AT, PS/2 are trademarks of International Busine ss
®
is registered trademarks of Intel® Corporation.
Machines Corporation.
Microsoft
®
Windows is a registered trademark of Microsoft®
Corporation.
RTL is a trademark of Realtek Semi-Conductor Co., Ltd.
C&T is a trademark of Chips and Technologies, Inc.
UMC is a trademark of United Microelectronics Corporation.
ITE is a trademark of Integrated Technology Express, Inc.
SiS is a trademark of Silicon Integrated Systems Corp.
VIA is a trademark of VIA Technology, Inc.
All other product names or trademarks are properties of their
respective owners.
ii
Remote Touch Display ACD-515R
Packing List
The LCD monitor comes with the following standard parts shown as
below. Check and make sure they are included and in good condition.
If anything is missing or damaged, contact the dealer immediately.
1 ACD-515R
1 Utility CD-ROM
Contains User’s Manual (in PDF format), Drivers and
Utilities
1 AC/DC 12V Power Adapter with Lock
If any of these items are missing or damaged, you should cont act y our
distributor or sales representative immediately.
iii
Remote Touch Display ACD-515R
Safety & Warranty
1. Read these safety instructions carefully.
2. Keep this user's manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Do
not use liquid or spray detergents for cleaning. Use a damp cl oth.
4. For pluggable equipment, the power outlet must be installed near
the equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation.
Dropping it or letting it fall could cause damage.
7. The openings on the enclosure are for air convection. Protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before
connecting the equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not
place anything over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the
power source to avoid damage by transient over-voltage.
12. Never pour any liquid into an opening. This could cause fire or
electrical shock.
13. Never open the equipment. For safety reasons, only qualified
service personnel should open the equipment.
iv
Remote Touch Display ACD-515R
14. If any of the following situations arises, get the equipment
checked by service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to
work according to the users manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED
ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS
BELOW -20° C (-4°F) OR ABOVE 60° C (140° F). IT MAY
DAMAGE THE EQUIPMENT
.
FCC
Cautio
This device complies with Part 15 FCC Rules.
Operation is subject to the following two
conditions: (1) this device may not cause
harmful interference, and (2) this device
must accept any interference received
including interference that may cause
undesired operation.
n:
It may cause the danger of explosion if battery is incorrectly
replaced. Replace only with same or equivalent type
recommended by the manufacturer.
v
Remote Touch Display ACD-515R
Below Table for China RoHS Requirements
产品中有毒有害物质或元素名称及含量
AAEON Display
有毒有害物质或元素
部件名称
印刷电路板
及其电子组件
外部信号
连接器及线材
外壳 × ○ ○ ○ ○ ○
液晶模块 × ○ ○ ○ ○ ○
触控模块 × ○ ○ ○ ○ ○
电源 × ○ ○ ○ ○ ○
O：表示该有毒有害物质在该部件所有均质材料中的含量均在
SJ/T 11363-2006 标准规定的限量要求以下。
X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出
SJ/T 11363-2006 标准规定的限量要求。
备注：
一、此产品所标示之环保使用期限，系指在一般正常使用状况下。
二、上述部件物质触控模块为选购品。
铅
(Pb)汞 (Hg)镉 (Cd)
× ○ ○ ○ ○ ○
× ○ ○ ○ ○ ○
六价铬
(Cr(VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
vi
Remote Touch Display ACD-515R
Contents
Chapter 1 General Information
1.1 Introduction................................................................ 1-2
1.2 Features....................................................................1-3
1.3 General Specification................................................1-4
1.4 Dimension .................................................................1-7
1.5 Network Topology ..................................................... 1-8
Chapter 2 Hardware Installation
2.1 Before Unpacking...................................................... 2-2
2.2 Connecting Power and Cables..................................2-3
2.3 VESA Wall Mounting................................................. 2-4
2.4 LED Definitions..........................................................2-5
2.5 Button Definitions......................................................2-5
2.6 DIP Switch................................................................. 2-7
2.7 Connecting Power of Remote Display ...................... 2-8
2.8 Connecting I/O Connectors of Remote Display ........ 2-8
2.9 Connection Debugging.............................................. 2-8
2.10 The Matching of the Remote Box and Remote
Display............................................................................. 2-9
Chapter 3 On Screen Display Control
3.1 On Screen Display (OSD) Board Description. .......... 3-2
3.2 OSD Main Menu: Push The MENU Keys..................3-3
vii
Remote Touch Display ACD-515R
3.3 Select Input Source................................................... 3-4
3.4 Contrast/ Brightness- Submenu................................ 3-5
3.5 Geometry Menu.........................................................3-6
3.6 Color Temperature- Submenu OSD Main Menu: Push
The MENU Keys.............................................................. 3-7
3.7 RGB Color- Submenu. .............................................. 3-8
3.8 Language- Submenu................................................. 3-9
3.9 Auto Config- Submenu..............................................3-10
3.10 Mode Resolution- Submenu Chapter...................... 3-11
3.11 Exit Menu- Submenu............................................... 3-12
Chapter 4 Touch Screen Driver Installation
4.1 Introduction................................................................ 4-2
4.2 Installing Driver for Windows
® XP/ Windows® 7 / Linux
.........................................................................................4-2
viii
Remote Touch Display ACD-515R
Chapter
1
Information
General
Chapter 1 General Information 1-1
Remote Touch Display ACD-515R
1.1 Introduction
Thank you for purchasing of the Infotainment Touch Display with
Remote Display Technology - a marvelous contribution of
cutting-edge technology.
The LCD monitor has been designed with serious thoughts to
present the best performance for most applications. Symbol of
elegance, its compact and slim profile are well suited in working
locations where space is at a premium.
The TFT LCD monitor displays sharper, more brilliant, crisper and
flicker-free images. Complying with the power management
regulations of VESA DPMS, the LCD monitor is extremely energy
efficient and a power saver. Plus, the LCD monitor has extremely
low radiation emissions and near zero electromagnetic fields which
are supreme benefits.
Fully compatible with PC system, the LCD monitor provides full
interface for all sorts of related standards. Supported by “Plug &
Play” complying with DDC1/DDC2B, installing the LCD monitor is
absolutely trouble free.
The On Screen Display menu provides user a convenient interface
to make right adjustment for optimum display performance.
Chapter 1 General Information 1-2
Remote Touch Display ACD-515R
1.2 Features
15.6” WXGA (1366 x 768) Fanless TFT LCD Display
Supports Remote Display Technology
Easy-To-Clean: Multi-Touch Window Design (Two-Point)
IP65 Front Bezel & IPx1 Back Chassis Protection
Anti-Scratch Surface (7H Hardness)
Chapter 1 General Information 1-3
Remote Touch Display ACD-515R
1.3 General Specification
System
Input signal
Control
I/O connector
OS Support
Mechanical
Construction
Mounting
Dimension
Carton
Dimension
VGA, DVI
OSD (On Screen Display) on the panel
USB x 3 (optional 2 on front, 1 on rear), LAN
x 2, Line-out x 1, 2W speaker x 2
Windows
Fedora (T/S: Single point), Windows
®
XP (T/S: Single point), Linux
®
7 (T/S:
Single point)
IP65/NEMA4 for plastic front bezel, IPx1 for
plastic chassis
VESA 75/100
15.51” x 10.71” x 2.2” (394mm x 272mm x
56mm)
20.47” x 18.5” x 9.06” (520mm x 470mm x
230mm)
Gross Weight
Net Weight
Environmental
Operating
Chapter 1 General Information 1-4
12.98 lb (5.9 Kg)
9.24 lb (4.2 Kg)
32°F~ 104°F (0°C to 40°C)
Remote Touch Display ACD-515R
Temperature
Storage
Temperature
Storage
Humidity
Vibration
Shock
EMC
Power Supply
DC Input
LCD
Display Type
Max.
Resolution
Max. Colors
Luminance
Brightness
-4°F~ 140°F (-20°C to 60°C)
10%~95% @ 40°C, non-condensing
1g rms/5-500Hz/random operation
15 G peak acceleration (11 msec. duration)
CE/FCC Class A
DC 12V, w/AC power adapter w/lock
15.6” TFT-LCD, CCFL
1366x768
16.7M colors (6/8-bit for R, G, B)
300 cd/m
300 cd/m
2
2
(TYP.)
Viewing Angle
Backlight
Backlight
170°(H)/ 160°(V)
CCFL
50,000
MTBF (hours)
Chapter 1 General Information 1-5
Remote Touch Display ACD-515R
Touchscreen
Type
Light
Transmission
Projected Capacitive Multi-Touch
(Windows
®
7)
90%
Chapter 1 General Information 1-6
Remote Touch Display ACD-515R
1.4 Dimension
Chapter 1 General Information 1-7
Remote Touch Display ACD-515R
1.5 Network Topology
1. One-to-one Network
The purpose of a one-to-one network is to allow a display to be used
anywhere away from the host PC. The display can be placed at any
location with Ethernet access. The entire VGA/DVI signal will be
transmitted from a host PC to a remote display via the Ethernet.
2. One-to-Multiple Network
The one-to-multiple network is a special design for digital signage
applications to show the same screen/audio in different display monitors.
The display can be placed in any area where you can get an Ethernet
connection. The screen & audio which is from the host PC can be shown in
remote displays via Ethernet
Chapter 1 General Information 1-8
Remote Touch Display ACD-515R
3. Cascade Network
The purpose of a cascade network is to save on cabling installation costs. It
is specially designed for digital signage applications with limited space
such as trains, buses and airports. With a cascade network set up, an end
user can deploy digital signage displays easily and save on installation
costs.
Chapter 1 General Information 1-9
Remote Touch Display ACD-515R
Chapter
2
H
Chapter 2 Hardware Installation 2-1
ardware
Inst
allation
Remote Touch Display ACD-515R
2.1 Before Unpacking
It is very important to place the LCD Display in a suitable
environment.
The surface for placing the LCD Display should be
stable and level.
Make sure the place has good ventilation, and out of
direct sunlight; away form sources of excessive dust,
dirt, heat, water, moisture and vibration.
Convenience for connecting the LCD Display the
related facilities should be well considered too.
Chapter 2 Hardware Installation 2-2
Remote Touch Display ACD-515R
2.2 Connecting Power and Cables
To power on the LCD Display, use the provided AC-DC adapter and the
power cord to connect to the power output socket of the monitor. Fasten
the connector securely.
ACD-515R-A1
ACD-515R-A2
12V power input with
lockable
Chapter 2 Hardware Installation 2-3
USB for Touchscreen
Remote Touch Display ACD-515R
2.3 VESA Wall Mounting
Mounting the LCD Display with UL Listed Wallmount Bracket only. The
LCD Display can be mounted on a monitor arm or wallmount plate.
Caution:
When mounting the LCD Display, take care to tighten the retention
screws or bolts until fully secured, but do not over tighten. Over tighting
the retention screws or bolts may cause them to become stripped,
rendering them useless.
Monitor Arm or Wallmount Plate Installation
The LCD Display has Video Electronics Standards Association (VESA)
standard mounting holes tapped into the rear panel. The standard holes
are M4 set at 75mm x 75mm apart.
VESA Mounting Holes
To mount the LCD Display onto a monitor arm or wallmount plate, please
follow the steps below.
Step 1: Line up the threaded holes on the monitor rear panel with
the screw holes on the monitor arm or wallmount plate.
Step 2: Secure the monitor to the arm or stand with the retention screws
supplied with the monitor arm or stand.
Chapter 2 Hardware Installation 2-4
Remote Touch Display ACD-515R
2.4 LED Definitions
Red LED Green LED Condition
Off Power off
Static Static Link established
Static Flash Link in process
Flash Off Load firmware
2.5 Button Definitions
There are three buttons on remote gateway and display. Refer to
the following LED definitions.
ACD-515R-A1 (One-to-multiple Network)
Short Press
Long press on Reset
(Press until Red LED
blinking)
Long Press on Reset
(Press until both
Red LED and
Green LED Blinking)
Link on: Link (Default)
SW1 SW2
Link off: Unlink
Engineering Mode* N/A
Engineering
Mode* and
Reset to default*
Chapter 2 Hardware Installation 2-5
Video Mode* (Default)
Graphic Mode*
Update EDID*
Remote Touch Display ACD-515R
ACD-515R-A2 (One-to-one Network)
Short Press
Long press on Reset
(Press until Red LED
blinking)
Long Press on Reset
(Press until both
Red LED and
Green LED Blinking)
*1: Graphic mode:
The system will get better performance of graphic/text in the screen. But it
would occupy larger bandwidth of the network.
*2: Video mode:
The system will adjust automatically between Ethernet bandwidth and
video quality. It would occupy smaller bandwidth of the network.
*3: Engineering mode:
(1)Static IP: 192.168.0.88
(2)User can connect to http://192.168.0.88 webpage for firmware
update.
(3) Firmware update file name will be: webfwc.bin
*4: Engineering mode:
(1) Reset Any change in SPI flash setup flag.
(2) Re-generate Random MAC to avoid any possible MAC collision.
After Reset to Default and reboot cycle, a new random MAC will be
generated.
*5: Update EDID:
The feature is used for one-to-multiple Mode to select which monitor/TV
EDID is used for system wide EDID usage. During one-to-multiple setup,
there may be monitor/TV that has lower resolution. For example, 1
monitor/TV with 720p resolution with mostly 1080p solutions. Please select
the monitor/TV with lowest resolution, to ensure all can be displayed
correctly. For customers who are using 1 pair of Host/Client with
one-to-multiple mode, the end user has to update EDID correctly. If not, it
Chapter 2 Hardware Installation 2-6
Link on: Link (Default)
SW1 SW2
Video Mode* (Default)
Link off: Unlink
Engineering Mode* N/A
Engineering
Mode* and
Reset to default*
Graphic Mode*
N/A
Remote Touch Display ACD-515R
A
will cause compatibility issues.
Operation:
The button event is triggered correctly at the remote display side, when
system is setup correctly for one-to-multiple. The selected EDID will be
update to Host Side EEPROM (HU7).
The same operation applies for Loopback EDID. In the system setup, the
last EDID updated will stay in the EEPROM. If customers setup this button
even many times, the last one triggered will be applied.
2.6 DIP Switch
The function of DIP switch is to make ACG-203 and remote displays in the
same group. When users want to send the data from the ACG-203 to
several remote displays (ACD-515R), they have to use the DIP switch to
set ACG-203 and ACD-515R the same grou p.
CD-515R
Chapter 2 Hardware Installation 2-7
Remote Touch Display ACD-515R
2.7 Connecting Power of Remote Display
Use the provided AC-DC adapter and the power cord to connect the power
output socket of the monitor to turn on the power.
A ”Surge Protection” device plugged between the AC-DC adapter and the
wall outlet is recommended to prevent the effects of sudden current
variations from reaching the LCD monitor. The sudden peaks of electricity
may harm the LCD monitor.
2.8 Connecting I/O Connectors of Remote Display
Turn off the computer and the LCD monitor before connecting them.
Use the RJ-45 CAT5/6 cable to connect to the RJ-45 connector.
Connect USB devices to the USB connectors.
2.9 Connection Debugging
If the connection or display cannot work well, please refer to the debugging
steps below.
Chapter 2 Hardware Installation 2-8
Remote Touch Display ACD-515R
Make sure that all the cables are connected tightly.
After the computer/display powered on, you will se e the display that
is reaching the local and remote IP below.
Local IP: The IP address of the display
If the display cannot find the local IP as shown, it means the
network connection/cabling has some issues
Remote IP: The address of the remote box, such as ACG-203
or ACG-204
If the display cannot find the remote IP, it means the remote
box may have some issues, so the IP address of the remote
box cannot be found
Below is the situation, which is searching the IP address
If the display or sound cannot work properly, please try the following
steps.
Make sure the local and remote IP can be found. If the IP
address cannot be found, please check the network cabling
Make sure the DVI/VGA and audio cable insert tightly
2.10 The Matching of the Remote Box and Remote Display
A1 Display (One to Multi/ Cascade) has to work with ACG-203-A1 or
ACG-204-A1
A2 Display (One to one) has to work with ACG-203-A2 or
ACG-204-A2
Chapter 2 Hardware Installation 2-9
Remote Touch Display ACD-515R
On Screen
Display Control
Chapter
3
Chapter 3 On Screen Display Control 3-1
Remote Touch Display ACD-515R
3.1 On Screen Display (OSD) Board Description
Buttons Description
Power Turn the monitor power ON or OFF.
Menu / Enter
UP / Right / Increase /
Input select
Down/ Left / Decrease
Auto
Activate the OSD menu.
Enter/confirm the selected option.
Move the selector to the next option.
Increase the gauge value of the
selected option.
Change input source.
Move the selector to the previous
option.
Decrease the gauge value of the
selected option.
Automatically adjust the clock,
phase, H-position and V-position.
Value to the most optimal settings.
Use full screen when enabling this
function.
Chapter 3 On Screen Display Control 3-2
Remote Touch Display ACD-515R
3.2 OSD Main Menu: Push The MENU Keys
A vailable Key Functions
Power On/Off the LCD Monitor
or
or
or
or
Increase the gaguge value of the selected option
Decrease the gaguge value of the selected option
Slected to confirm
Return to last menu
Chapter 3 On Screen Display Control 3-3
Remote Touch Display ACD-515R
3.3 Select Input Source
A vailable Key Functions
Power On/Off the LCD Monitor
or
or
or
or
Increase the gaguge value of the selected option
Decrease the gaguge value of the selected option
Slected to confirm
Return to last menu
Chapter 3 On Screen Display Control 3-4
Remote Touch Display ACD-515R
3.4 Contrast/ Brightness- Submenu
A vailable Key Functions
Power On/Off the LCD Monitor
or
or
or
or
Increase the gaguge value of the selected option
Decrease the gaguge value of the selected option
Slected to confirm
Return to last menu
Chapter 3 On Screen Display Control 3-5
Remote Touch Display ACD-515R
3.5 Geometry Menu
A vailable Key Functions
Power On/Off the LCD Monitor
or
or
or
or
Chapter 3 On Screen Display Control 3-6
Increase the gaguge value of the selected option
Decrease the gaguge value of the selected option
Slected to confirm
Return to last menu
Remote Touch Display ACD-515R
3.6 Color Temperature- Submenu
A vailable Key Functions
Power On/Off the LCD Monitor
or
or
or
or
Increase the gaguge value of the selected option
Decrease the gaguge value of the selected option
Slected to confirm
Return to last menu
Chapter 3 On Screen Display Control 3-7
Remote Touch Display ACD-515R
3.7 RGB Color- Submenu
A vailable Key Functions
Power On/Off the LCD Monitor
or
or
or
or
Chapter 3 On Screen Display Control 3-8
Increase the gaguge value of the selected option
Decrease the gaguge value of the selected option
Slected to confirm
Return to last menu
Remote Touch Display ACD-515R
3.8 Language- Submenu
A vailable Key Functions
Power On/Off the LCD Monitor
or
or
or
or
Increase the gaguge value of the selected option
Decrease the gaguge value of the selected option
Slected to confirm
Return to last menu
Chapter 3 On Screen Display Control 3-9
Remote Touch Display ACD-515R
3.9 Auto Config- Submenu
A vailable Key Functions
Power On/Off the LCD Monitor
or
or
or
or
Chapter 3 On Screen Display Control 3-10
Increase the gaguge value of the selected option
Decrease the gaguge value of the selected option
Slected to confirm
Return to last menu
Remote Touch Display ACD-515R
3.10 Mode Resolution- Submenu
A vailable Key Functions
Power On/Off the LCD Monitor
or
or
or
or
Increase the gaguge value of the selected option
Decrease the gaguge value of the selected option
Slected to confirm
Return to last menu
Chapter 3 On Screen Display Control 3-11
Remote Touch Display ACD-515R
3.11 Exit Menu- Submenu
A vailable Key Functions
Power On/Off the LCD Monitor
or
or
or
or
Increase the gaguge value of the selected option
Decrease the gaguge value of the selected option
Slected to confirm
Return to last menu
Chapter 3 On Screen Display Control 3-12
Remote Touch Display ACD-515R
Chapter
4
Touch Screen
Driver Installation
Chapter 4 Touch Screen Driver Installation 4-1
Remote Touch Display ACD-515R
4.1 Introduction
The optio na l ACD-515R Series touch screen uses Pro je ct ed
Cap a c i t i v e M u l t i - T o u c h technology to provide more accurate sensing
capacity than other technologies. The touch screen is specially
designed for infotainment environments, and has been approved by
FCC Class A standards.
4.2 Installing Driver for Windows
®
XP/ Windows® 7 / Linux
The touch screen has drivers for Windows® XP、 Windows® 7 and
Linux . You should read the instructions in this chapter carefully
before you attempt installation.
Note 1: We don’t install driver for Windows®7 since Windows® 7 has
been built in multi-touch driver
Note 2
: ACD series just support single touch on Windows® XP, and
need to install the driver.
Note 3
: The driver installations of ACD-515R are the same as
ACD-515D’s. Therefore, the photos below are for your information.
For Linux Fedora 14 kernel 2.6.35-45.fc14 OS:
CD-ROM:
\\TouchScreen-DRV\eGalax Touch \ Linux\ eGTouch_v1.00.0726.L-x32
1. Open System
1-1. Select Applications
1-2. Select System Tools
Chapter 4 Touch Screen Driver Installation 4-2
Remote Touch Display ACD-515R
1-3. Select Terminal
1-4. Input Commandsu and System Password
2. Input commandcd Desktop
Chapter 4 Driver Installation 4-3
Remote Touch Display ACD-515R
2-1 Input commandls (This is the lowercase L)
2-2 all files of desktop will appear in window.
(Please copy the driver on desktop first.)
2-3 Input commandcd eGTouch_v1.00.0726.L-x32
Chapter 4 Touch Screen Driver Installation 4-4
Remote Touch Display ACD-515R
2-4 Input commandls (This is the lowercase L)
2-5 The information of the folder, “eGTouch_v1.00_0726.L-x32”, would
appear in the window.
2-6 Input commandExecute Touch Driver
Chapter 4 Driver Installation 4-5
Remote Touch Display ACD-515R
3. Reboot
4. Change the permission
Input commandchmod△777△/etc/eGTouchd.ini
5. Select Computer (You can modify the value of the Y axis to reverse
action principle.)
Chapter 4 Touch Screen Driver Installation 4-6
Remote Touch Display ACD-515R
6. Select “File System”
7. Select the “etc” folder
8. Select the “eGTouchd.ini” file
Chapter 4 Driver Installation 4-7
Remote Touch Display ACD-515R
9. Select “Display”
10. Modify the value of “Direction” from 0(default)2(setting)
Chapter 4 Touch Screen Driver Installation 4-8
Remote Touch Display ACD-515R
11. Execute “Save”
Note
: If you want to change X or Y axis, please refer to the description of
“Direction” as red circle below.
12. Reboot
Chapter 4 Driver Installation 4-9
Remote Touch Display ACD-515R
13 . Input command./eGTouch (Execute Driver) and select the file of
“eGTouch32”.
13-1. Input command./EventTest (Execute AP)
14. Draw and test (Drawing、Writing)
15. If you want to replace the Interface, please remove the Touchd
Driver
Input commandsh setup.sh uninstall (Must Under
eGTouch_v1.00.0726.L-x32 folder under)
Chapter 4 Touch Screen Driver Installation 4-10
Remote Touch Display ACD-515R
16. Reboot
Chapter 4 Driver Installation 4-11
Loading...