Page 1
PowerSaver R7
Wireless Desktop
User’s Guide
Model: RK（S）-6&R7-70MD，RK（S）-6&R7-70D，RK（S）-8&R7-70D
www.a4tech.com
Page 2
PowerSaver R7 Wireless Optical Mouse
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1)
THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Federal Communications Commission Requirements
The equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to
radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
z Reorient of relocate the receiving antenna.
z Increase the separation between the equipment and receiver.
z Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
z Consult the dealer or an experienced radio/TV technician for help.
The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
- 1 -
Page 3
PowerSaver R7 Wireless Optical Mouse
INTRODUCTION
Congratulations on your purchase!
Congratulations on your purchase!
PowerSaver R7 Wireless Desktop is the optimal high science products for power & desktop space saving. Its
innovative lightweight, mini & thin wireless keyboard design gives you a consistent desktop look as well as an
amazingly high level of comfort. your new RF-Mouse is designed with R7 Extremely Low-Power Technology only
requires 8mA electric current while others require 25mA. Wow! Just turn your mouse battery –life 3 times longer.
Same time, PowerSave R7 performs high-speed RF technology with report rate of 125Hz
mice performs with reports rate of only 90Hz (Tested by Mouse Rate Program)]
z Package contains：
PowerSaver R7 Wireless Keyboard
PowerSaver R7 Wireless Optical Mouse
USB RF Receiver
USB Extension Cable
4 AAA Alkaline Batteries
User’s Quick Guide
CD Driver
- 2 -
[**Normal wireless optical
Page 4
PowerSaver R7 Wireless Optical Mouse
z System Requirements:
To use the mouse presenter, your computer must meet the following hardware requirements and run one of the
operating system listed below.
Hardware
1. IBM or compatible system
2. UBS v1.1 or higher interface
3. Hard Disk Driver
4. USB Port
Operating System
Windows®98/Me/2000/2003/XP/x64
z This user’s guide describes how to：
1. Connect the receiver to your computer
2. Set up the wireless link and use the mouse
3 .Install software driver
- 3 -
Page 5
PowerSaver R7 Wireless Optical Mouse
Inserting the Batteries
z Install 2 AAA alkaline（or rechargeable batteries）in the
wireless keyboard.
1. Remove the battery compartments cover on the bottom of the
keyboard by squeezing the cover in front the tab to release it.
2. Insert the batteries; make sure to properly orient the positive (+)
and the negative (-) ends as specified by the battery compartment
labels.
3. Replace the cover.
z Install 2 AAA alkaline（or rechargeable batteries）in the wireless mouse.
1. Press the tab on the bottom of the mouse cover as shown here and remove the cover.
2. Insert the supplied batteries, making sure that the positive (+) and negative (-) ends of the battery match the
polarity indicators inside the battery housing.
3. Slide the batter cover back into position until it “clicks” firmly into place.
- 4 -
Page 6
PowerSaver R7 Wireless Optical Mouse
Step1 Step2 Step3
To connect the receiver
Insert the Receiver USB port connector into the available computer USB port. You can choose anyway to
connect the USB receive with computer as blow:
For PC computer usage:
1. Insert the USB receive mouse port connector into the USB port on the
USB extend cable (accessories),
- 5 -
Page 7
p
PowerSaver R7 Wireless Optical Mouse
2. Insert the USB receives mouse port connector into the USB HUB port.
Locating the USB RF-Mouse Receiver
Your RF-Mouse has limitations on the range or distance from its receiver. To make sure that your mouse sends and
receives properly, refer to the following instructions:
1. For optimal performance, place the receiver at least 8 inches
(20 centimeters) away from other electrical devices, such as
the computer, the monitor, or external storage drives.
2. The RF-Mouse should be no farther than 4 feet (1. 5meter)
from the mouse receiver. This will ensure optimal
communication between the mouse and receiver.
Keep 8 inches
- 6 -
Kee
4 feet
Page 8
PowerSaver R7 Wireless Optical Mouse
Operating Hints: For optimal performance and RF reception:
1. Avoid suing the mouse on a metal surface, Metals, such as iron, aluminum or copper, shield the radio frequency
transmission and may slow down the mouse’s response time or cause the mouse presenter to fail temporarily.
2. The mouse will enter a suspend mode at the same time your computer dose, click a button on the mouse
presenter to activate it.
3. Never use the mouse on a glass or mirrored surface as these surface will the mouse to fail temporarily
Establish Frequency Channel and ID Code
Step one: how Connecting the Wireless Keyboard ID Code?
1. USB RF Mouse Receiver: lanuch frequency channel
and ID code
Press and release the connect button on the front of USB receiver
(shown as right image), the GREEN PWR LED light turns “Off” and
starts “Blinking.
- 7 -
to RF-keyboard
Page 9
PowerSaver R7 Wireless Optical Mouse
2. Wireless Keyboard : Respond frequency channel
and ID code from Receiver
z Press and release (1 second) the (Frequency Button) orange
connect button on the bottom of keyboard
z The RED PWR LED light of USB RF Receiver turns “Off” and
starts “Blinking with right frequency channel and ID code.
z If the GREENPWR LED light of USB RF Receiver is black out, it
indicates that the right frequency channels and ID codes are
launched successfully between the receiver and the keyboard,
Step two: how to Connecting the Wireless Mouse ID Code?
1. USB RF Mouse Receiver: lanuch frequency channel
and ID code
Press and release the connect button on the front of USB receiver
(shown as right image), the GREEN PWR LED light turns “Off” and
starts “Blinking.
to RF-Mouse
Frequency Button
- 8 -
Page 10
PowerSaver R7 Wireless Optical Mouse
Wireless optical mouse : Respond frequency channel
and ID code
z Press and release (1 second) the orange connect button on
the bottom of mouse,
z The RED PWR LED light of USB RF Receiver turns “Off” and
starts “Blinking with right frequency channel and ID code .
z When the mouse is inactive, If the GREENPWR LED light of
USB RF Receiver is black out, it indicates that the right
frequency channels and ID codes are launched successfully
between the receiver and the mouse, otherwise, repeat the
procedures of the right frequency channel and ID codes. You
are now ready to use the mouse.
Note：The connect button has two functions. One function is correspond frequency with USB receiver. Other
function is power switch. you can control power on-off through it (please operate as “Power Management”
show )
from Receiver
1. Frequency Button
2. Power on/off
- 9 -
Page 11
PowerSaver R7 Wireless Optical Mouse
Power Management
Manual Power on/off method
1. To power the mouse on, please press and release the switch bottom of the
mouse within in 1 second.
2. Turn off the mouse while traveling or when you don’t use it. Please press and
release the switch bottom of the mouse within 4 seconds. (if you use this
mouse , you must to power the mouse on again)
Automatic Power on/off method
If this mouse is keep non-operation in 30 minute, Mouse turns off automatically. If you awaken this mouse, you can
click left or right button on the mouse.
Low Battery Warning
when your battery power is low, Smart wheel LED light turns to Red for 0.3 seconds
and it will be off after 0.9 seconds in interval
Note: Removing the batteries will require you to synchronize it with the receiver again the next time you turn it back on.
- 10 -
Page 12
PowerSaver R7 Wireless Optical Mouse
Practical electrical current usage text sheet (on white paper)
Battery Voltage (V) Use Electrical Current (mA)
3.3 6.9
3.2 7.0
3.1 7.3
3.0 7.4
2.9 7.6
Intelligent 4 Power-Saving (SLEEP MODE)：
There are 4 sleep mode features activating PowerSaver mouse
Mouse status Enter Sleep mode Electrical Current usage(mA) Savable electricity(mA)
200 milliseconds
non-operation
5 seconds non-operation sleeping mode 0.8 7.2
70 seconds non-operation deep sleeping mode 0.1 7.9
30 minute non-operation turns off automatically 0.01 7.99
To wake up the mouse from sleep mode, you must click left or right button on the mouse.
- 11 -
idle mode 2.1 5.9
Page 13
PowerSaver R7 Wireless Optical Mouse
How to install 2X-Office Software
**** For Windows 98/ME/2000/2003/XP/X64
1. MUST:
2. MUST:
3. Insert the included Compact Disc (CD) into your CD-ROM
4. choose your mouse model and click” install Driver”
5. Follow the on screen instruction to complete your installation
6. Restart your computer after the driver has been installed
7. You will see a mouse icon “
bar (near the clock area)
8. Double click on the mouse icon “
(Image: Mouse Properties Window)
9. If the mouse image appears in the mouse properties menu looks exactly
the same as the mouse on hand, then you have successfully installed
the 2X-OFFICE driver
Please uninstall any previous mouse driver before installing the 2X-OFFICE
Make sure you have completely finished setting up your mouse
” appear on the bottom right of your task
” will bring you the mouse property
Mouse Properties Window
- 12 -
Page 14
PowerSaver R7 Wireless Optical Mouse
How to program your mouse bottoms?
z Open your Mouse Properties.
First Tab: Button
Section I: Button Assignment
1. The mouse image that appears in the first section is a key to numbers
listed to the right.
For example， # 1 button has been assigned as “Main Button” by default
and it’s not programmable.
MOUSE PROPERTY
# 2 button has been assigned as “Right Button” which works as right click
for your mouse
# 3 button has been assigned as “Pan” function by default. It’s a vertical
scrolling wheel if you scroll it. Also, # 3 wheel button can be using as a
“Net/LuckyJump”, you need to open the Mouse Properties window and
select the Button tab as left image shown. Then assign Net/LuckyJump in
rd
wheel button command. You also can use “Setting” to update the
3
command list of Net/LuckJump. Press the wheel button, it will show up
NetJump or LuckyJump screen which shows 14 commonly used tasks as
- 13 -
Page 15
PowerSaver R7 Wireless Optical Mouse
for convenient shortcut
th
#4 、#5 buttons can be set as either regular programmable buttons or Office-Button functions. The 4
the coupling button to makes shortcut command from Office-jump such as “OPEN, CLOSE”; “DELETE, REPLY”,
th
“ZOOM IN, ZOOM OUT”…etc. which may be easily changed by one click on the 6
OfficeJump button.
and 5th as
Section II: Double-Click Speed
Section III: Button Configuration
Adjust your double-click speed If you select “Left-Handed”, your Main Button will be #2 button.
Before we go further to setting up your mouse buttons with game
commands, we want to make sure your keyboard properties has the
character repeat setting correct. Follow the steps below to get to
Keyboard Properties:
1) Go to Control Panel
2) Click on Keyboard
3) For Repeat Delay: Most right (SHORT)
4) For Repeat Rate: Most right (FAST)
Keyboard Property
5) Apply >> OK
- 14 -
Page 16
PowerSaver R7 Wireless Optical Mouse
Learn how to use the “Office Button Options
1. There are 2 ways to open the “Office-Button” menu
(right)
● Click the “Office-Button Option” in the Mouse
Properties
● Click 6th Button located on your physical Mouse
Body and will bring you the small picture:
2. Once you click on A4 company logo,
you will see the Office Button menu like the figure on the right big
image(Office-Button menu)
3. There are total of 24 selections in the Office-Button menu. You may
Office-Button menu
choose up to maximum of 8 selections at a time.
STEP FOUR : EXPERIENCE THE MOUSE WITH DIFFERENT APPLICATIONS
When you are in Microsoft Outlook
After selected Office command set No.5 - Delete-Reply All . You can press 6th button to delete all garbage
th
mail, or you can press 7
manage your outlook in a second. Or you can select No.15 - Zoom In- \Zoom out
button to reply all. By using Mouse, you can instantly read all your email messages and
to enlarge your email font
size to match your eyesight needs
- 15 -
Page 17
PowerSaver R7 Wireless Optical Mouse
When you are in Microsoft Word
After selected Office Command set No.1 - Copy-Paste
sentences with simply two clicks. Instead of looking for copy icon and paste icon in the MS Word or Ctrl+C and
Ctrl+V on the Keyboard. Or you can select No.15 - Zoom In- \Zoom out
match your eyesight needs.
When you are in Microsoft Excel
After selected Office command set No.14 - Scroll left-Scroll right
second with such a handful function
When you are in Photoshop, Illustrator, Pro-E or other applications
After selected Office Command Set No.15 - Zoom In- \Zoom out
whether to do some editing to the image or just to view the image more clearly with just two clicks.
More than 100 useful applications are supported with our “Zoom in-Zoom out” command set
There are so many different computer applications that provides zoom in and out functions. However, each of
these various applications uses different ways to execute the Zoom function, which can be difficult to neither
learn nor remember the proper way in performing the Zoom functions. Now, with A4 Tech Zoom in and out
function, whether you are an Artist, Designer or Office user, you can easily press the two zoom buttons to
interactive with more than hundreds of applications. We integrated and standardized different Zoom commands
into our two office fingertips, and this function can be use in all Windows applications that use Zoom-supported
. You can adjust your paragraph length or edit
to enlarge the page view size to
. You can edit your wide spreadsheet in a
, you can enlarge or shrink the image size
functions.
- 16 -
Page 18
PowerSaver R7 Wireless Optical Mouse
Popular Hotkeys for Wireless Keyboard
There are 7programmable Hotkeys which default functions are automatically supported by Windows2000 or above
Windows OS.
You have to establish the iKeyWorks to enable the Hotkeys in Windows98 OS.
1. Through A4 download web page : http://www.a4tech.com/en/download1.asp to download the keyboard
driver.
2. Double click the Winzip driver file then click “ I Agree” to open the file and start to install .
3. Locate the file’ Setup.exe” then click “next” till ‘”finish” to accomplish the installation.
Hot Keys Default Functions
Cut off the computer power
Power
Back Back to previous page
Forward Forward to next page
Refresh
Refresh the page
Home page
Search
E -mail
TECH SUPPORT
For tech support, please visit our website at http://support.a4tech.com/ or email us at support@a4tech.com
- 17 -
Access your default web page.
Web search
Launches an e-mail application.
Loading...