2.4G RF Dongle
User Manual
Model: RG-30
www.a4tech.com
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT
CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
Federal Communications Commission Requirements
The equipment has been tested and found to comply with the limits for Class B Digital
Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction, may cause harmful interference to radio
communication. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
z Reorient of relocate the receiving antenna.
z Increase the separation between the equipment and receiver.
z Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
z Consult the dealer or an experienced radio/TV technician for help.
THE CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY
RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
FCC Radiation Exposure Statement
The equipment complies with FCC radiation exposure limits set forth for uncontrolled
equipment and meets the FCC radio frequency (RF) Exposure Guideline s in Su ppleme nt C
to OET65. The equipment has very low levels of RF energy that it is deemed to comply
without testing of specific absorption ratio (SAR).
Knowing the Product
Far Range Up to 15 Meters
X-Far Wireless range ensures more operation
freedom.
(Note: Actual operating distance may vary and
depend on working environments)
8 Gestures in Right Button
The mouse allows you get 8 functions on “Right”
button.
Battery Status Indicator
Aware of the battery power anytime with A4 Tech’s
uniquely designed “8 in Right” software
Hardware Installation
Plug receiver into USB port of your computer or notebook.
Insert the supplied battery, making sure that the positive (+) and negative (-) ends of
the battery match the polarity indicators inside the battery housing. and power will be
automatically on. Now you can use the mouse or keyboard.
Power Management of the Mouse
1. To power on the mouse, press the power button for
approximate 3 seconds.
2. To turn off the mouse power, press the power button on
the bottom of the mouse till the LED light is off.
Note: The mouse can be awaked easily by moving the
mouse randomly if long time no using.
The wireless mouse or keyboard is plug-and-play. No driver is required. If you would like to
get more function, please install the software (enclosed on the CD) first
Software Installation
1. Before installing the mouse software, please uninstall any previous installed
mouse software.
2. Insert enclosed CD to start installation.
3. Follow on-screen instructions to complete the installtion.
4. The icon
software.
5. To launch the software,
double click the icon on
your desktop or go to
Start—Programs—8 in
Right, then the icon will
appear in the taskbar at the
right corner of your screen.
will appear on your desktop, then you have successfully installed the
Software Instructions
A. How to get 8 functions in right button of the mouse
From the “task pull-down” menu of each arrow direction, you can select “keyboard,
mouse, office sets, key combinations, multimedia and internet” 6 main function
categories and there are more than 30 different functions that are ready for your
immediate selection.
Task Pull-down Menu
B. How to Pair the X-Far Wireless Devices
The mouse have been preset the ID Code in the factory. But under the circumstances you
lose receiver or want to use with the other receiver in the same product series, you need
to refresh the ID Code before using it.
Step 1: Right click on the icon
taskbar
“Pair ID Program”
in the
and select
Step 2: Press “Start Pair ID” to
refresh ID Code.
Step 3: Remove the mouse or keyboard batteries and insert again in 15 seconds，
6 digits of matching code will be displayed on the menu as shown “Mouse or
Keyboard Pair ID OK”.
C. How to Indicate Battery Status
All of G7 Mouse series have Battery
status Indicator in the software, click
”in the main menu of the
“
software, then the battery power
status will be displayed on the
screen. It is convenient that you can
easily be aware when the battery
power is low and change battery in
time.
Note:There are four levels: 100%、
75%、50% and 25% respectively，if
the value is less than 25%, it is
recommended that you should
change the battery right away.
Notice:
read below instructions for your reference:
1. To avoid electromagnetic interference, place the receiver at least 8 inches (20 cm) away
from other electrical devices, such as the computer, the monitor or external storage
devices.
2. The operation distance depends on the working environment and can reach to 15
meters without any interference, to get optimal performance, please adjust the distance
between mouse and receiver according to different situations.
3. Avoid using the wireless mouse on a metal surface. Metals such as iron, aluminum, or
copper shield the radio frequency transmission and slow down the mouse’s response
time or cause the mouse to fail temporarily.
To ensure that your mouse or keyboard sends and receives perfectly, please
Troubleshooting
If the mouse or keyboard are not working:
1. Make sure the mouse or keyboard is power on.
2. Check battery installation.
3. Check receiver installation.
4. Try another USB port.
Loading...