A4Tech G9-540F User Manual

User Manual

Model: G9-540F

www.a4tech.com

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT
MAY CAUSE UNDESIRED OPERATION.

Federal Communications Commission Requirements
The equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction, may cause harmful interference to radio communication.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:

●Reorient of relocate the receiving antenna.

●Increase the separation between the equipment and receiver.

●Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

●Consult the dealer or an experienced radio/TV technician for help.

THE CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR
COMPLIANCE COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and receiver.
(2) This device must accept any interference received, including interference that may cause undesired
operation.

FCC Radiation Exposure Statement
The equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets
the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. The equipment has very low
levels of RF energy that it is deemed to comply without testing of specific absorption ratio (SAR).

1. Hardware Installation

1

1). Connect the Multi-link receiver
Take out the Multi-link receiver from bottom of the mouse and connect it to your computer.

2). Insert the batteries
Open the battery cover and insert the supplied batteries.
Note: Make sure the positive (+) and negative (-) ends of the battery match the polarity indicators inside the
battery compartment.

3). Turn on your Mouse
Push the power switch to ON position and turn on your mouse. >>Then LED light at the bottom of the mouse
is on immediately.

4). Position the wireless mouse and Multi-link receiver within 15m operating range (Note: The actual distance
depends on the environment.)

Note: For more functions such as RF Channel Lock, Gesture 16-in-1, 4-way Wheel and so on, please install
the G9 16-in-1(enclosed in the CD) software first!

2. Software Installation (Note: The software is

Windows 7)

applicable to Windows 2000/ XP/ 2003/ Vista/

2

1). Uninstall previous installed mouse software.

2). Insert the enclosed CD to start installation and follow the on-screen instructions to finish the software
installation.

3). The shortcut icon "
software. (Otherwise, installation is failed and you have to remove the software and re-install.)

" will appear on your desktop screen, and then you have successfully installed the

To remove the software, follow the steps:

Go to Start >> Programs >> A4TECH Software >> G9 16-in-1 >> Uninstall G9 16-in-1

To launch the software

Double click on the icon " " at the right-down corner of your system tray or double click on the icon " " at
your desktop screen. The "Main Menu" of "16-in-1" software will pop up.

3. Knowing the "16-in-1" software

"16-in-1" software offers programmable 16 functions in 1 click with RIGHT button.

3

Gesture 16-in-1

1). Click "

will pop up as below.

" of "Gesture Button  " at the "Main Menu" page and select "Gesture 16-in-1". The setup screen

Setup Screen

2). Click any "

used commands to the "Gesture Button ", and then click "Apply" at "Main Menu" of "16-in-1" software to save
your new setting! There are more than 30 commands you may select, including Keyboard, Mouse, Office, Text,
Multimedia, Internet and Open a file.

3). Knowing "16-in-1" functions

Function list Function instruction
No Setting There is no button setting being defined.
Keyboard You may setup the "Gesture Button" to simulate a keyboard’s keystroke, or a key

" at "Setup Screen", you will see the function list. Now you may setup 16 most-frequently-

combination with “Win”, “Ctrl”, “Shift” and “Alt”, then followed with any keystroke on the
keyboard, and then assign it to the "Gesture Button".

4

Mouse You may setup "Gesture Button" to be one of “mouse left button, mouse right button,

Open a File You may setup the "Gesture Button" to open a file or program by one-click during

wheel up and wheel down”.

presentation.
Usage:

1). Select “Open a File” from the pull-down menu of the "Gesture Button" as "Figure 1"
shows.

Figure.1 Figure 2

2). A screen of file listings will pop up as "Figure 2" shows.

3). Select a file that you would open it with the "Gesture Button " and click “Open”.

4). Now you can see a file you selected has been assigned to "Gesture Button."

5). Click “Apply” to save the new setting.

Example: While make a presentation, it is embarrassing to keep others waiting due to searching for a
document, or look up for a program or a shortcut. With “Open a File” function, you may have better way to
resolve this issue. By setting up "Gesture Button②" in association to the document, program or shortcut, all

you need to do is to open any file instantly with "Gesture Button②" .



5

Office Sets You may setup any one of Office command sets such as: “Zoom In, Zoom Out, Paste

Text
Commands
Multimedia Quick access to Multimedia commands, such as: Media Player (Open), Previous, Next,

Internet: Quick access to usually used Internet commands, such as: Backward, Forward, Stop,

Text” to the "Gesture Button".

1. Zoom In/Out：One click to perform zoom in or zoom out function, applicable to CAD,
ACDSee, Windows or text editing programs.

2. Paste Text：One click to perform “Select, Copy & Paste” texts, it turns office jobs can
never be so simple.
Quick access to Office, such as: New File, Open File, Save File, Redo, Undo.

Stop, Play/Pause, Mute, Volume+, Volume-…etc.

Refresh, Search, My Favorite, Web Browser, E-mail...etc.

How to use "Gesture Button" as "16-in-1" function

Press and hold the gesture button to draw any of 16 lines and directions
as shown on the right, then release the button. The corresponding
commands will be executed immediately, including Keyboard, Mouse,
Office, Text, Multimedia, Internet and open a file, which can be preset
and store to your receiver memory.

Example 1:

Using
file in the Office, or Reading a PDF file…etc, just pressing the “Gesture Button ”and draw the line as shown
below, then release the “Gesture Button ”, the picture or the document will be zoomed in immediately.

as “Zoom In” command by default, when you are viewing a picture with ACDSee, or browsing a PPT

Diagrams of 16 mouse

gestures

6