A4 Tech G10-770L User guide

MeetingMan

TutorPen/ LaserPointer 20m Wireless Mouse

User Manual

Model: G10-770L

www.a4tech.com

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE
MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING I NTERFERENCE
THAT MAY CAUSE UNDESIRED OPERATION.

Federal Communications Commission Requirements

The equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communication. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

●Reorient of relocate the receiving antenna.

●Increase the separation between the equipment and receiver.

●Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

●Consult the dealer or an experienced radio/TV technician for help.

THE CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S
AUTHORITY TO OPERATE THE EQUIPMENT.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and receiver.
(2) This device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement

The equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in
Supplement C to OET65. The equipment has very low levels of RF energy that it is deemed to comply without testing of specific absorption ratio (SAR).

- 1 -

Mouse Button Diagram:

- 2 -

1. Hardware Installation

1). Connect the 10-Link receiver
Take out the 10-Link receiver from bottom of the mouse and connect it to your computer or
Notebook.

Notes:

1. If you are using the receiver in a long range meeting room or there is strong wireless
conflicts nearby, adopting the receiver with a USB extension cable to keep it away from the
computer or any interfering sources.

2. Connect receiver on the same side with the mouse, it may avoid potential wireless
conflicts from the notebook computer.

2). Insert the batteries
Push down the mouse cover to open the battery cover and insert the supplied batteries.
Please make sure the positive (+) and negative (-) ends of the battery match the polarity
indicators inside the battery compartment.

3). Turn on your Mouse
Push the power switch to ON position and turn on your mouse. >>Then LED light at the

bottom of the mouse is on immediately.

- 3 -

2. Software Installation(Note: The software is applicable to Windows 2000/ XP/ 2003/ Vista/ Windows 7)

The G10 MeetingMan offers 2 flexible ways to install the driver, Normal Installation and Mobile Execution. The MeetingMan
main program has a special feature that it can be executed directly without the need to install the software to Windows
system. This is convenient when you are using a public computer and installing mouse driver to the system is prohibited or
restricted. In such circumstances, you do not need to install the mouse driver, but just run the MeetingMan’s main

program directly from your storage device, e.g., a memory stick.

- 4 -

Normal Installation

1). Uninstall any mouse software on your system.

2). Insert enclosed CD to start installation and follow the on-screen instructions to finish the
software installation. You may manually double click the “auto-run” program if execution

does not automatically start.

3). The shortcut icon "
installed the software. (Otherwise, installation is failed and you have to remove the software

and re-install.)

To remove the driver, follow the steps:

Go to START>> PROGRAMS >>A4TECH Software >> "G10 MeetingMan" >> "Uninstall G10

MeetingMan, see figure on the right.

Mobile Execution:

You may copy and store the Mobile Edition files to your storage device, e.g., a memory stick,
and plug it into any public systems to execute the Mobile Edition directly without installation.
Or, you may copy all the files to the system, and then run the Mobile Edition main program
directly. This is convenient when you are using a public computer in the school or net bar,

where installation any new program is prohibited or restricted.

Usage:

1). Copy all the files in the folder “G10” to your memory stick, and if needed, copy the files
to the public system.

2). Double-click the icon to run Mobile Edition.exe

" will appear on your desktop screen, and then you have successfully

- 5 -

Mobile Edition.exe