The 150Mbps Wireless Broadband Router is dedicated to Small Office/Home Office (SOHO)
Wireless network solution. It is 4 in 1 network device, which combines wireless access point,
firewall, 4-port Switch and the NAT-Router. It provides up to 150Mbps data transmission rate
in 2.4GHz frequency, complies with IEEE 802.11n, IEEE 802.11g and IEEE802.11b and
backwards compatible with all IEEE 802.11n/g/b devices. And the router also supports
wireless LAN up to 128-bit WEP, WPA/WPA2 encryption security. The 150Mbps Wireless
Broadband Router also provides WEB and Remote Management and system log so that
network administrators can manage and monitor the network in real time.
The 150Mbps Wireless Broadband Router also provides a hardware WPS (Wi-Fi protected
setup) button, which helps you setup a secure wireless network in a snap. The button lets you
activate the wireless protection easily.
1.2. Main Features
Comply with IEEE802.11n/g/b, IEEE802.3 10Base-T, IEEE802.3u 100Base-TX
standards
Support MIMO technology with 1 transmit and 1 receive, up to 150Mbps wireless LAN
data transfer rates
Support DHCP Client, PPPoE Client, Static IP, L2TP, PPTP
Support multi-wireless mode: AP, WDS, AP+WDS, repeater, client, etc.
Support static ARP, MAC filtering, IP access control, DNS filter
Support FTP, PPTP and L2TP pass through
Support UPNP (universal plug and play)
Upgradeable firmware for future functions
WPS button can easily setup a secure network
Support WMM
Support data encryption mode: WEP, WPA, WPA2
Support DMZ
0° to 40° C (operating)
-40° to 70° C (storage)
Humidity
10% to 90 % non-condensing (operating)
5% to 90% non-condensing (storage)
Power
DC 9V
7
150Mbps Wireless Broadband Router User Manual
2. Hardware Installation
2.1. System Requirement
Minimum Requirements:
Broadband (DSL/Cable) modem and service with Ethernet port
802.11n b/g/n wireless adapter or Ethernet adapter and cable for each computer
Internet Explorer® 5.0, Firefox® 2.0 or Safari® 1.4 or higher
2.2. Panel
Front panel
LED Status Meaning
Device is on
SYS Flashing
On WAN connection is active
WAN
Flashing Data transfer
On LAN connection is active
LAN (1 to 4)
Flashing Data transfer
Device system activated
WPS activity (LED is orange)
8
150Mbps Wireless Broadband Router User Manual
Rear panel
Description Function
PWR
LAN 1-4 Connect with computer NIC or Ethernet device
WAN Internet access
Reset Restore settings
Connect to Power adapter, please don’t use the unknown
power adapter, otherwise your device may be damaged.
2.3. Restore to factory configuration
If the router ever freezes in a setting change process or if you can’t access it because you can’t
remember the IP you have given it or other problem, you may have to utilize the reset button on
the back of the router to put it back to factory settings. You have to press and hole this button
for a few seconds (2-6s) with a pencil when it is working, then release and it will restore
settings to the factory configuration.
The other way to restore factory settings is through the same user interface used in setup.
Click on ‘System management’- ‘Restore’, and click on the ‘Restore’ button.
2.4. Hardware Installation Procedures
The procedures to install the 150Mbps Wireless Broadband Router please refers to the
following picture
9
150Mbps Wireless Broadband Router User Manual
Attach one end of an Ethernet cable to your computer’s Ethernet port, and the other end to
one of the LAN ports of your router.
Connect another Ethernet cable from your Cable/DSL modem to the WAN port of your
router.
Connect the single DC output connector of the power adapter to the power jack on the back
of the router and plug the Power Adapter into an AC outlet.
10
150Mbps Wireless Broadband Router User Manual
3. Login
You can manage the 150Mbps Wireless Broadband Router through the Web browser-based
configuration utility. To configure the device via Web browser, at least one properly configured
computer must be connected to the device via Ethernet or wireless network. The 150Mbps
Wireless Broadband Router is configured with the default IP address of 192.168.1.1 and subnet mask of 255.255.255.0 and its DHCP server is enabled by default. Before setting up
the Router, make sure your PCs are configured to obtain an IP address automatically from the
Router by the steps below.
3.1. Configure computer
3.1.1. Windows XP
Please follow the steps below to setup your computer:
1. Go to Start Settings Control Panel.
2. Click Network and Internet Connections.
3. Click Network Connections.
11
150Mbps Wireless Broadband Router User Manual
4. Highlight the icon Local Area Connection, right click your mouse, and click Properties.
5. Highlight Internet Protocol (TCP/IP), and then press Properties button.
12
150Mbps Wireless Broadband Router User Manual
6. Choose Obtain an IP address automatically and Obtain DNS server address automatically,
and then press OK to close the Internet Protocol (TCP/IP) Properties window.
7. Press OK to close the Local Area Connection Properties window.
13
150Mbps Wireless Broadband Router User Manual
3.1.2. Windows Vista
Please follow the steps below to setup your computer:
1. Go to Start Settings Control Panel.
2. Click Network and Sharing Center.
3. Click Manage Network Connections.
14
150Mbps Wireless Broadband Router User Manual
4. Highlight the icon Local Area Connection, right click your mouse, and click Properties.
5. Highlight Internet Protocol Version 4 (TCP/IP) and then press Properties button.
15
150Mbps Wireless Broadband Router User Manual
6. Choose Obtain an IP address automatically and Obtain DNS server address automatically,
and then press OK to close the Internet Protocol (TCP/IP) Properties window.
16
Loading...
+ 41 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.