3xLogic VX-2A-B-RIWDZ, VX-2AD3B-IWD, VX-2AD3-IWD, VX-2A-IMD-X, VX-2VA-B-RIWD Hardware And Installation Manual

Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I

10385 Westmoor Drive, Suite 210, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC

1

VISIX V-Series All-in-One Cameras - Gen I

Hardware and Installation Manual

2018-3

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

2

This manual applies to the following camera models. Please use the below links or the Table of Contents
to locate the section of this manual that pertains to your particular All-in-One camera model:

Camera Type

Model

Exterior Bullet Camera

VX-2A-B-RIWDZ (New), VX-2A-B-IWD (DC)

Exterior Bullet Camera w/Remote Focus

VX-2VA-B-RIWD (New), VX-2A-B-RIWD (DC)

Exterior Dome Camera

VX-2AD3B-IWD (New), VX-2AD3-IWD (DC)

Interior Mini Dome Camera

VX-2A-IMD-X

VERA 20°, 36° or 50° Field-of-Vision Thermal Bullet
Camera

VX-VT-20, VX-VT-36, VX-VT-58 (New)

Interior Pinhole Camera

VX-2V28-PIN

Please use the links above or the Table of Contents to locate the section of this manual that pertains to
your particular All-in-One camera model.

Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to
contact the dealer.

This manual may contain technical inaccuracies or printing errors. The content is subject to change
without notice. The manual will be amended if there are any hardware updates or changes.

Disclaimer Statement

“Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability of the security or

signaling aspects of this product. UL has only tested for fire, shock or casualty hazards as outlined in UL’s
Standard(s) for Safety, UL60950-1. UL Certification does not cover the performance or reliability of the
security or signaling aspects of this product. UL MAKES NO REPRESENTATIONS, WARRANTIES OR
CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR
SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.”

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

3

Regulatory Information

FCC Information

FCC compliance: This equipment has been tested and found to comply with the limits for a digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause undesired

operation.

EU Conformity Statement

This product and - if applicable - the supplied accessories too are marked with "CE"
and comply therefore with the applicable harmonized European standards listed
under the Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC, the
RoHS Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection points. For
more information see: www.recyclethis.info.

2006/66/EC (battery directive): This product contains a battery that cannot be
disposed of as unsorted municipal waste in the European Union. See the product
documentation for specific battery information. The battery is marked with this
symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the battery to your supplier or to a
designated collection point. For more information, see: www.recyclethis.info

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

4

Safety Instruction

These instructions are intended to ensure that the user can use the product correctly to avoid danger or

property loss.

The precaution measure is divided into ‘Warnings’ and ‘Cautions’:

WARNING: Serious injury or death may be caused if any of these warnings are neglected.
CAUTION: Injury or equipment damage may be caused if any of these cautions are neglected.

WARNINGS:

 Please adopt a power adapter which can meet the safety extra low voltage (SELV) standard

when possible, and source with 12 VDC or 24 VAC (depending on models) according to the
IEC60950-1 and Limited Power Source standard. Before applying power to the camera,
check the power source to ensure that it is within the specifications

 If the product does not work properly, please contact your dealer or the nearest service

center. Never attempt to disassemble the camera yourself. (We shall not assume any
responsibility for problems caused by unauthorized repair or maintenance.)

 To reduce the risk of fire or electrical shock, do not expose this product to rain or moisture

unless it is an exterior/weatherproof model. Please do not install the camera in a place
exposed to direct sunlight. Do not operate the camera in environments beyond the
specified temperature. Refer to your specific camera model’s section of this manual for
environmental conditions and limitations.

 This installation should be made by a qualified service person and should conform to all the

local codes.

 Please install blackout equipment into the power supply circuit to prevent footage and

data loss.

 Please make sure that the ceiling can support more than 50(N) Newtons of gravity if the

camera is fixed to the ceiling.

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

5

CAUTIONS:

 Make sure the power supply voltage is correct before using the camera.
 Do not drop the camera or subject it to physical shock.
 Do not touch sensor modules with fingers. If cleaning is necessary, use a clean cloth with a

bit of ethanol and wipe it gently. If the camera will not be used for an extended period of
time, put on the lens cap to protect the sensor from dirt.

 Do not aim the camera lens at the strong light such as sun or incandescent lamp. The

strong light can cause fatal damage to the camera.

 The sensor may be burned out by a laser beam, so when any laser equipment is being

used, make sure that the surface of the sensor not be exposed to the laser beam.

 Do not place the camera in extremely hot, cold temperatures (the operating temperature

should be between -30°C ~ 60°C, or -40°C ~ 60°C if the camera model has an “H” in its
suffix), dusty or damp environment, and do not expose it to high electromagnetic
radiation.

 To avoid heat accumulation, good ventilation is required for a proper operating

environment.

 Keep the camera away from water and any liquid.
 While shipping, the camera should be packed in its original packing.
 Improper use or replacement of the battery may result in hazard of explosion. Please use

the manufacturer recommended battery type.

NOTE: For cameras that support IR, you are required to pay attention to the following precautions to

prevent IR reflection.

► Dust or grease on the dome cover will cause IR reflection. Please do not remove the

dome cover film until the installation is finished. If there is dust or grease on the dome
cover, clean the dome cover with clean soft cloth and isopropyl alcohol. (only applies
to certain models).

► Make certain the installation location does not have reflective surfaces of objects too

close to the camera. The IR light from the camera may reflect back into the lens
causing reflection. (only applies to certain models).

► The foam ring around the lens must be seated flush against the inner surface of the

bubble to isolate the lens from the IR LEDS. Fasten the dome cover to camera body so
that the foam ring and the dome cover are attached seamlessly (only applies to certain
models).

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

6

Table of Contents

1 VISIX V-SERIES ALL-IN-ONE CAMERAS ............................................................................................ 8

1.1 INTRODUCTION ................................................................................................................................. 8

2 VX-2A-B-RIWDZ / VX-2VA-B-RIWD - 2MP EXTERIOR BULLET CAMERA ........................................... 9

2.1 VX-2A-B-RIWDZ/ VX-2-VA-B-RIWD SPECIFICATIONS- QUICK SUMMARY ............................................... 9

2.2 PACKAGE CONTENTS ........................................................................................................................ 10

2.3 PART NAMES .................................................................................................................................. 11

2.4 INSTALLATION ................................................................................................................................. 12

2.4.1 Installing the Camera – Installation without Bracket ......................................................... 12

2.4.2 Adjusting angle of the camera ............................................................................................ 14

2.4.3 Adjusting Zoom and Focus (VX-2A-B-IWD Model Only) ...................................................... 14

2.5 CONNECTIONS ................................................................................................................................ 15

2.6 FULL CAMERA SPECIFICATIONS ........................................................................................................... 17

2.7 CAMERA DIMENSIONS ...................................................................................................................... 19

3 VX-2AD3B-IWD / VX-2AD3-IWD - 2 MP EXTERIOR DOME CAMERA .............................................. 20

3.1 VX-2AD3B-IWD SPECIFICATIONS- QUICK SUMMARY ........................................................................... 20

3.2 PACKAGE CONTENTS ........................................................................................................................ 21

3.3 PART NAMES .................................................................................................................................. 22

3.4 INSTALLATION ................................................................................................................................. 23

3.4.1 Installing the Camera – Installation without Bracket ......................................................... 23

3.4.2 Reattachment of Dome Cover – Alignment ........................................................................ 25

3.4.3 Adjusting angle of the camera ............................................................................................ 25

3.4.4 Connections ........................................................................................................................ 26

3.5 FULL CAMERA SPECIFICATIONS ........................................................................................................... 27

3.6 CAMERA DIMENSIONS ...................................................................................................................... 29

3.7 COMPATIBLE ACCESSORY INSTALLATION (MOUNTS) ............................................................................... 30

3.7.1 Wall Mount- VX-2AD-WM ................................................................................................. 30

3.7.2 Ceiling Mount- VX-2AD-CM ............................................................................................... 32

3.7.3 Pendant Mount Cap - VX-2AD-PMCB ................................................................................. 34

3.7.4 Gang Box Mount – VX-2AD-GB ........................................................................................... 35

4 VX-2A-IMD-X - 2 MP INTERIOR MINI DOME CAMERA ................................................................... 37

4.1 VX-2A-IMD-X SPECIFICATIONS - QUICK SUMMARY .............................................................................. 37

4.2 PACKAGE CONTENTS ........................................................................................................................ 38

4.3 PART NAMES .................................................................................................................................. 39

4.4 INSTALLATION ................................................................................................................................. 40

4.4.1 Installing the Camera – Installing without Bracket ............................................................ 40

4.4.2 Adjusting angle of The camera ........................................................................................... 42

4.5 CONNECTIONS ................................................................................................................................ 42

4.6 FULL CAMERA SPECIFICATIONS ........................................................................................................... 43

4.7 CAMERA DIMENSIONS ...................................................................................................................... 45

4.8 COMPATIBLE ACCESSORY INSTALLATION (MOUNTS) ............................................................................... 46

4.8.1 Wall Mount - VX-2AIMD-WM ............................................................................................. 46

4.8.2 Location of the Holes for M3x6L Bolts ................................................................................ 48

4.8.3 Ceiling Mount - VX-2AD-CM ............................................................................................... 49

4.8.4 Pendant Mount Cap - VX-2AD-PMC .................................................................................... 51

5 VX-VT-20, VX-VT-36, VX-VT-58 – VERA 20°, 36°, 58° THERMAL BULLET CAMERA .......................... 53

5.1 VX-VT-20, VX-VT-36, VX-VT-58 SPECIFICATIONS – QUICK SUMMARY .................................................. 53

5.2 PACKAGE CONTENTS ........................................................................................................................ 54

5.3 PART NAMES .................................................................................................................................. 55

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

7

5.4 INSTALLATION ................................................................................................................................. 56

5.4.1 Installing The camera – installation without bracket ......................................................... 56

5.4.2 Adjusting angle of The camera ........................................................................................... 58

5.5 CONNECTIONS ................................................................................................................................ 59

5.6 FULL CAMERA SPECIFICATIONS ........................................................................................................... 61

5.7 CAMERA DIMENSIONS ...................................................................................................................... 62

6 VX-2V28-PIN – IP PINHOLE CAMERA ............................................................................................ 63

6.1 VX-2V28-PIN SPECIFICATIONS — QUICK SUMMARY ............................................................................ 63

6.2 PACKAGE CONTENTS ........................................................................................................................ 64

6.3 PART NAMES .................................................................................................................................. 65

6.3.1 Main Unit: ........................................................................................................................... 65

6.3.2 Camera Unit with Conjoined Accessories............................................................................ 66

6.4 INSTALLATION ................................................................................................................................. 67

6.4.1 Camera Unit Installation ..................................................................................................... 67

6.4.2 Inconspicuous Installation .................................................................................................. 67

6.4.4 Surface Installation for Fixed Angle .................................................................................... 69

6.4.5 Surface Installation for Pan/Tilit Adjustment ..................................................................... 70

6.4.6 MAIN UNIT INSTALLATION .................................................................................................. 71

6.5 CABLE CONNECTION ......................................................................................................................... 73

6.5.1 DI/Do Terminal Connector .................................................................................................. 73

6.5.2 Camera Connector .............................................................................................................. 74

6.5.3 LAN Connector .................................................................................................................... 75

6.5.4 Power Connector ................................................................................................................ 75

6.6 CAMERA DIMENSIONS ...................................................................................................................... 76

6.7 FULL CAMERA SPECIFICATIONS ........................................................................................................... 77

7 POWER OVER ETHERNET SPECIFICATIONS .................................................................................... 79

7.1 POWER COMPARISON ...................................................................................................................... 79

8 REVISION HISTORY ....................................................................................................................... 80

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

8

1 VISIX V-Series All-in-One Cameras

1.1 Introduction

VISIX V-Series All-in-One, edge-based IP cameras are powerful, full-featured, VMS and advanced analytic
capable. VISIX V-Series cameras provide a complete surveillance solution for the small and medium sized
businesses and for unique single-point applications.

Several models exist to best suit any number of environments. Hardware installation details for each
model are contained within. Use the Table of Contents to locate the Section pertaining to your particular
camera model.

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

9

2 VX-2A-B-RIWDZ / VX-2VA-B-RIWD - 2MP

Exterior Bullet Camera

The VX-2A-B-RIWDZ (previous model: VX-2A-B-IWD) and VX-2VA-B-RIWD (previous model: VX-2A-B­RIWD) are fully functional indoor/outdoor IP cameras with advanced analytics capabilities. These
cameras can be connected to a DVR or act as a standalone recording device. The exterior bullet camera
line offers high-definition video at full 1920 x 1080 resolution for both indoor and outdoor video
surveillance applications which require superior clarity and detail.

The wealth of features includes; dual-streaming of either H.264 or MJPEG compression; wide dynamic
range; Micro SD card slot for local recording; IP66 weather resistant construction; varifocal lens; and IR
illumination. The RIWD model also features remote one-click auto focus.

The embedded analytics use algorithms that automatically self-adjust, allowing the user to concentrate
on the detection rules. This greatly simplifies the analytic process, requiring only a few mouse clicks to
configure a detection rule. These advanced analytics allow for object classification, direction, people
counting, dwell times, and occupancy counts.

When enabled, the embedded VIGIL Server software from 3xLOGIC allows the camera to be run as a
stand-alone device recording video to the onboard memory card. This makes the camera compatible
with the 3xLOGIC software suite including VIGIL Client, VIGIL VCM, VIGIL Mobile and VIGIL Cloud
applications. Simple plug-and-play installation allows for access using a standard web browser, VIGIL
Client, or your mobile device or tablet using our easy to use QR code quick setup.

2.1 VX-2A-B-RIWDZ/ VX-2-VA-B-RIWD Specifications- Quick

Summary

Component

Feature Description

Camera

 SONY EXMOR 1/2.9” 1080p CMOS Image Sensor
 True Day / Night
 DC Auto Iris Lens
 WDR
 Embedded IR Illuminator
 Weather Proof (IP66)
 Remote Zoom/Focus Control (One Click AF) - ** VX-2-VA-B-RIWD

Only**

Video

 H.264 Baseline, Main, High profile (MPEG-4 Part 10/AVC),

MJPEG(Motion JPEG)

 Max 30fps in 1080p
 Text Overlay
 Analog Video Output

Network

 10/100 Base-T Ethernet

Integration

 ONVIF compliant (Profile S)

General

 Micro SD/SDHC Card Slot x1
 Power over Ethernet (PoE)

Video Contents Analysis
(VCA)

 VCA Presence Standard

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

10

2.2 Package Contents

Please unpack the package carefully and handle the equipment with care. The package contains:

NOTE: The contents above are subject to change without prior notice.

Camera

DC Power Adaptor

Universal Plugs

Screws(M4x30) and Plastic Anchors

Quick Installation Guide

Hex Wrench(3mm)

Silicon Waterproof Band

Video Output Cable

Installation Template

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

11

2.3 Part Names

1). Sunshield: Position the sunshield to prevent direct sunshine.

2). Video-Out Cable Socket: Socket for the video output cable included in the package (CVBS: 1.0Vp-p /

75Ω BNC)

3). PAL/NTSC button: Pressing the PAL/NTSC button each time changes the mode as follows: No video

output -> PAL-> NTSC

4). Reset button: Use the button to restart the device or to reset it to Factory Default. Refer to the

3xLOGIC VISIX All-in-One Camera User Manual for more details on restarting/resetting to factory
default.

5). Focus Puller: Use the puller to manually determine correct focus of the camera. Refer to Adjusting

Zoom and Focus for more details.

6). Zoom Puller: Use the puller to manually determine appropriate field of view of the camera. Refer to

Adjusting Zoom and Focus for more details.

7). microSD memory card slot: The camera supports up to 32GB. A card with Class 4 and higher is

recommended for HD recordings.

8). Terminal Connector: Connector for cable connection of digital input/output. Refer to Section 2.5:

Connections for more details.

9). Power Adaptor Connector: Use DC12V for the power supply.

10). LAN connector: RJ45 LAN connector for 10/100 Base-T Ethernet (PoE supported)

❾

* Models herein and their appearance are subject to change without any prior notice.

❸

❹

❿

❽

❷
❼

❺

❶

❻

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

12

2.4 Installation

2.4.1 INSTALLING THE CAMERA – INSTALLATION WITHOUT BRACKET

Installation Template

NOTE: Installation template’s image size scale in this installation guide is not 1:1. The correct-size

template design paper can be found inside the package separately.

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

13

Steps:

1). Place the installation template included in the package

on the desired installation surface.

2). Drill three holes in correct positions based on the

template paper, and insert the anchor blocks into the
holes.

3). Attach the silicon waterproof band included in the

package to the camera’s mounting surface by aligning it
with the three alignment holes.

4). Connect the required cables including a power cable

and a LAN cable (or PoE connection) to the device. See
Section 2.5: Connections for a diagram of the correct
connections.

5). Place the camera body to match the three alignment

holes with the three anchor blocks, and hold the camera
against the surface where the camera will be mounted.

6). Tighten the anchor blocks with the screws.

7). Adjust the heading direction of the camera. Refer to

Adjusting Angle of the Camera for more details.

8). Adjust zoom and focus of the camera. Refer to Adjusting

Zoom and Focus for more details.

9). Attach the lens cover on the main body by rotating it

clockwise

CAUTION: Sealing gaps is recommended as gaps may appear after

the camera installation. Gaps may cause problems such as
moisture, water leakage, and etc., which negatively affects the
operation of the camera if gaps remain unsealed.

CAUTION: To prevent products from damage, place the camera

on a stable and non-vibrating surface. If the stability is in doubt,
consult safety personnel for reinforcements, and then proceed
with the installation.

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

14

2.4.2 ADJUSTING ANGLE OF THE CAMERA

Adjust the camera to the desired angle by unscrewing the joints referring to the following pictures.

Steps:

1). Insert the video output cable (included in the

package) to the video output cable socket, and
connect it to an analogue video test monitor to
check if the camera angle has been set as
intended. If the angle is appropriate, disconnect
the camera from the analogue monitor, and then
remove the video output cable from the camera.

2.4.3 ADJUSTING ZOOM AND FOCUS (VX-2A-B-

IWD MODEL ONLY)

Steps:

1). Unscrew the zoom puller and the focus puller

counter-clockwise.

2). Adjust the zoom and the focus of the lens.

3). Tighten the zoom puller and the focus puller again by

turning it clockwise after the zoom and the focus are
properly adjusted.

CAUTION: Manual adjustment of Zoom and Focus is only

possible on the VX-2VA-B-IWD model version. Zoom and Focus controls can be configured digitally from

the camera’s web interface for VX-2VA-B-RIWD models. See the VISIX V-Series All-in-One Camera User
Manual for more details on adjusting lens settings from the camera’s web interface.

Adjust the joint to install
the camera on the wall.

Tilting adjustment

Panning adjustment

Zoom Puller

Focus Puller

Reset

PAL/NTSC

Video output
cable

socket

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

15

2.5 Connections

LAN cable

GREEN : DI

WHITE : DI COM
ORANGE : DO

YELLOW : DO COM

(not included)

DC 12V

❶

❷

❸

❹

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

16

1). Sensor (DI) connection: Sensor (DI) can be connected to either a voltage type sensor or a relay type

sensor as the following figures. Settings can be done through the camera’s webpage.

 Input voltage range: 0VDC minimum to 5VDC maximum, Max 50mA.

CAUTION: Do not exceed the maximum input voltage or relay rate.

2). Alarm (DO) Connection: Only the relay type is supported.

 Relay Rating: Max 24VDC 50mA

CAUTION: Do not exceed the maximum relay rating.

3). LAN Connection: This is a RJ45 LAN connector for 10/100 Base-T Ethernet. Use the Ethernet cable

(RJ45. to connect the device to a hub or a router in the network. Refer to Section 6: Power over

Ethernet Specifications to for further detail.

4). Power Connection: The camera can be powered from either 12VDC or PoE. If the camera is

powered via PoE, refer to Section 6: Power over Ethernet Specifications for further detail.

+3.3V

DI

COM

DI

COM

+

-

Relay Type

Voltage Type

+

-

Output of
Sensor

Output of
Sensor

Internal

Internal

+

-

DO

COM

Relay Type

Device

Internal

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

17

2.6 Full Camera Specifications

Camera Module

CMOS

Image Sensor

SONY EXMOR 1/2.9” 1080p CMOS

Effective Pixels

1920x1080

Scanning system

Progressive scanning

Electrical

Resolution

1920 x 1080

Min. Illumination

Color: 0.7 lux, BW: 0 lux (IR LED On)

AGC Control

Auto

Lens

3.0(w) – 9.0mm(t), F1.5(w) – F2.5(t), Optical 3x

Day & Night

Removable IR Cut Filter

Wide Dynamic
Range

Digital WDR

IR Illuminator

IR LED

High Power IR LED x 12 (850nm)

IR Working
Distance

Max. 30m (98ft)

Video

Compression
Format

H.264 and MJPEG Selectable per Stream

Number of
Streams

Dual Stream, Configurable

Resolution

1920x1080, 1280x720, 1120x630, 960x540, 800x450, 640x360, 480x270,
320x180

Compression FPS

30fps@1080p

Motion Detection

Built-in

Burnt-in Text
(Digital)

Time stamp and text caption overlay

Analogue Output

NTSC/PAL

Audio

Input/output

-

Compression
Format

-

Function

Digital
Input/Output

1/1 channel

RS-485

Not supported

Network

10/100 Base-T

Power over
Ethernet (PoE)

Supported

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

18

Function

Protocol

QoS Layer 3 DiffServ, TCP/IP, UDP/IP, HTTP, HTTPS, FTP, RTSP, RTCP, RTP/UDP,
RTP/TCP, mDNS, UPnP™, SMTP, DHCP, DNS, DynDNS, NTP, SNMPv1/v2c/v3(MIB­II), IGMP, ICMP, SSLv2/v3, TLSv1

SD Slot

1 x microSD memory card slot
(SD/SDHC up to 32 GB supported)
※ Card not included
(Class 4 and higher recommended for HD recordings)

Electrical Characteristics

Power Source

DC 12V / PoE

Power
Consumption

Max. 6W @ DC 12V

Video Output

1 Vp-p, 75, Composite

Audio Input

-

Audio Output

-

D/I

Max 50mA@5VDC, TTL level 1.5V threshold

D/O

Max 50mA@24VDC
On-state resistance: 50  (max continuous)

Environment Condition

Operating
Temperature

[DC12V] -20°C ~ 50°C (-4°F ~ 122°F)
[PoE] -20°C ~ 50°C (-4°F ~ 122°F)

Operating
Humidity

Up to 85% RH

Mechanical Condition

Material

Aluminum Die-Casting

Color

Ivory

Dimension

83.5mm X 86mm X 287 mm

Weight (Approx.)

860g (1.90lbs)

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

19

2.7 Camera Dimensions

 2.68 in.
(68 mm)

3.29 in. (83.5 mm)

9.41 in. (239 mm)

4.67 in. (118.5 mm)

3.39 in. (86 mm)

3.29 in. (83.5 mm)

11.02 in. (280 mm)

11.30 in. (287 mm)

3 x .197 in. (5mm)

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

20

3 VX-2AD3B-IWD / VX-2AD3-IWD - 2 MP Exterior

Dome Camera

The VX-2AD3B-IWD (previous model: VX-2AD3-IWD) is a fully functional indoor/outdoor IP camera with
advanced analytics capabilities. These cameras can be connected to a DVR or act as a standalone
recording device.

The exterior dome offers high-definition video at full 1920 x 1080 resolution for both indoor and
outdoor video surveillance applications which require superior clarity and detail. Its many features
include; dual-streaming of either H.264 or MJPEG compression; wide dynamic range; Micro SD card slot
for local recording; IP66 weather resistant construction and IR illumination.

The embedded analytics use algorithms that automatically self-adjust, allowing the user to concentrate
on the detection rules. This greatly simplifies the analytic process, requiring only a few mouse clicks to
configure a detection rule. These advanced analytics allow for object classification, direction, people
counting, dwell times, and occupancy counts.

When enabled, the embedded VIGIL Server software allows the camera to be run as a stand-alone
device recording video to the onboard memory card. This makes the camera compatible with the
existing 3xLOGIC software suite including VIGIL Client, VIGIL VCM, VIGIL Mobile and VIGIL Cloud
applications. Simple plug and play installation allows for access using a standard web browser, VIGIL
Client, or set it up on your mobile device or tablet using our easy to use QR code quick setup.

3.1 VX-2AD3B-IWD Specifications- Quick Summary

Component

Feature Description

Camera

 1/2.9” 1080p CMOS Image Sensor
 True Day/Night
 WDR
 Embedded IR Illuminator

Video

 H.264 Baseline, Main, High profile (MPEG-4 Part 10/AVC), MJPEG (Motion

JPEG)

 Max 30fps in 1080p
 Text Overlay

Network

 10/100 Base-T Ethernet

Integration

 ONVIF compliant (Profile S)

General

 Micro SD/SDHC Card Slot x1
 Power over Ethernet (PoE)

Video Contents
Analysis (VCA)

 VCA Presence Standard

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

21

3.2 Package Contents

Please unpack the package carefully and handle the equipment with care. The package contains:

Camera

Screw(M4x35) & Plastic Anchors

Quick Installation Guide

Torx (T20) Wrench

O-ring & Waterproof Bracket

Installation Template

Bottom Pad

Adaptor & AC Plug

NOTE: The contents above are subject to change without prior notice.

Camera

Camera

Cable

Camera

Cable

Torx Wrench

Screw &
Plastic Anchor-3pcs

Quick Installation Guide

O-ring &
Waterproof Bracket

Bottom Pad

Installation Template

Camera

Cable

Torx Wrench

Screw &
Plastic Anchor-3pcs

O-ring &
Waterproof Bracket

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

22

3.3 Part Names

1) Safety Wire: The dome cover is attached to the camera body with this safety wire to prevent

the dome cover from being dropped.

2) Ambient Light Sensor: Used to detect the level or the intensity of light for the IR operation. The

sensor should not be blocked by any object.

3) MicroSD/SDHC Card Slot: Up to 32GB supported. Class 4 and higher recommended for HD

recordings.

4) Reset Button: Use the button to restart the device or to reset it to Factory Default. Refer to the

3xLOGIC VISIX All-in-One Camera User Manual for more details on restarting/resetting to
factory default.

5) RJ-45: Connect an RJ-45 LAN cable for 10/100 Base-T Ethernet (PoE supported).

6) DC Power Jack: Connect the provided DC12V adaptor for the power supply unless it is PoE

powered.

* Models herein and their appearance are subject to change without any prior notice.

Reset Button

DC Power

RJ-45

Safety Wire

Ambient Light Sensor

microSD/SDHC Card Slot

❻

❷

❶
❺

❹
❸

Safety Wire

Ambient Light Sensor

mircoSD/SDHC Card Slot

Reset Button

RJ-45

DC Power

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

23

3.4 Installation

3.4.1 INSTALLING THE CAMERA – INSTALLATION WITHOUT BRACKET

Installation Template

CAUTION: Installation template’s image size scale in this installation guide is not 1:1. The correct-size

template paper can be found inside the product packaging.

M o unting tem p late

 4.92 in.
(125 mm)

 .255 in. (6.5 mm)

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

24

Steps:

1). Place the installation template included in the package on the desired installation surface.

2). Drill two holes for the plastic anchors and a big hole for the cable lines based on the template

paper, and insert the plastic anchors into the drilled holes.

3). Attach the provided bottom pad to the bottom of the camera body for the prevention of

water permeation.

4). Detach the dome cover from the camera body by loosening the three screws with the

provided T20 Torx wrench.

5). Make the screws (M4x35) ready for the installation: Insert the provided waterproof bracket

and the O-ring into the screw in a row by placing the head of the bracket beneath the screw
head by reference to the squared image on the left.

6). Take the camera to the ceiling, and connect the necessary cables including a LAN and power

cable (or PoE cable) dropped from the ceiling to the corresponding connectors on the camera.

7). Align the screw holes on both sides of the camera body and the installation surface, insert the

screws prepared at the step 5 into the screw holes on the camera body, and tighten them into
the plastic anchors on the ceiling with a screw driver.

8). Adjust the angle of the camera. Refer to Adjusting Angle of the Camera for more details.

9). Reattach the dome cover to the camera body by aligning the screws on the dome cover with

the alignment holes on the camera body. Refer to the caution below for the alignment
method.

10). Once properly aligned, tighten the screws into the camera body with the provided Torx

wrench for the firm attachment of the dome cover. Then, remove the protection film from the
dome cover.

Bottom

O-Ring

Waterproof Bracket

Screw
(M4x35)

Torx Bolt
(M4 x 20)

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

25

3.4.2 REATTACHMENT OF DOME COVER – ALIGNMENT

The screw hole where the cable line passes has a block next to it due to the cables
underneath. Thus, the part shaped differently from the other two screw hole parts
shall be aligned with the corresponding part of the dome cover, which is also shaped
differently from the other two parts.

Refer to the image on the right for the clarification.

CAUTION: Do not forcefully pull or shake the dome cover as it is linked to the

camera body with a safety wire.

CAUTION: To prevent products from damage, install the camera on stable and non-vibrating surfaces. If

the stability of a mount surface is in doubt, consult the safety personnel for reinforcements, and then
proceed with the installation.

3.4.3 ADJUSTING ANGLE OF THE CAMERA

Adjust the angle of the camera by manually moving the corresponding parts by reference to the directions
below.

CAUTION: Refrain from continuous rotation of the camera gimbal or the inner liner to a single direction

as they are attached to the IR-LED cable inside.

CAUTION: Be careful not to make the ambient light sensor hidden by the dome cover when adjusting

the camera angle. The ambient light sensor shall be uncovered for its normal operation.

NOTE: Tighten the tilt stopper screw after the angle adjustment is completed.

A. To pan, rotate the gimbal

bracket horizontally.

C. For the horizontal rotation of

the lens, rotate the inner liner
clockwise or counter-clockwise
with the inner liner.

B. To tilt, tilt the camera gimbal by

vertically adjusting it.

Gimbal Bracket

Camera Gimbal

Gimbal Bracket

Tilt Stopper Screw

Inner Liner

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

26

3.4.4 CONNECTIONS

1). LAN Connection: This is a RJ45 LAN connector for 10/100 Base-T Ethernet. Use the Ethernet cable

(RJ45 to connect the device to a hub or a router in the network. Refer to Section 6: Power over

Ethernet Specifications for further detail.

Power Connection: The camera can be powered from either 12VDC or PoE. If the camera is powered via
PoE, refer to Section 6: Power over Ethernet Specifications for further detail.

Camera

LAN cable

Power Adaptor

RJ-45

DC Power

❶

❷

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

27

3.5 Full Camera Specifications

Camera Module

CMOS

Image Sensor

1/2.9” 1080p CMOS

Effective Pixels

1920x1080

Scanning system

Progressive scanning

Electrical

Resolution

1920 x 1080

Min. Illumination

Color: 0.5 lux, BW: 0 lux (IR LED On)

AGC Control

Auto

Lens

4.0mm, F1.8

Day & Night

True Day & Night

Wide Dynamic
Range

Digital WDR

Video

Compression
Format

H.264 Baseline, Main, High profile(MPEG-4 Part 10/ AVC),
MJPEG(Motion JPEG)

Number of
Streams

Dual Stream, Configurable streams in H.264, MJPEG
H.264: Controllable frame rate, bandwidth(VBR/CBR)
MJPEG: Controllable frame rate, JPEG quality

Resolution

1920x1080, 1280x720, 1120x630, 960x540, 800x450, 640x360, 480x270,
320x180

Compression FPS

30fps@1080p

Motion Detection

Built-in

Burnt-in Text
(Digital)

Video stream overlay text

Audio

Input/output

-

Compression
Format

-

Function

Digital
Input/Output

-

RS-485

-

Network

10/100 Base-T

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

28

Function

Power over
Ethernet (PoE)

Supported

Protocol

QoS Layer 3 DiffServ, TCP/IP, UDP/IP, HTTP, HTTPS, FTP, RTSP, RTCP, RTP/UDP,
RTP/TCP, mDNS, UPnP™, SMTP, DHCP, DNS, DynDNS, NTP, SNMPv1/v2c/v3(MIB­II), IGMP, ICMP, SSLv2/v3, TLSv1

SD Slot

1 x microSD memory card slot
(SD/SDHC up to 32 GB supported)
※ Card not included
(Class 4 and higher recommended for HD recordings)

Electrical Characteristics

Power Source

DC 12V / PoE IEEE802.3af (Class 0)

Power
Consumption

Max. 5.4 W @ DC 12V

Video Output

-

Audio Input

-

Audio Output

-

D/I - D/O - Environment Condition

Operating
Temperature

-20˚C ~ 50˚C (-4˚F ~ 122˚F)

Operating
Humidity

Up to 85% RH

Mechanical Condition

Material

Aluminum Die-Casting (Vandal Resistance)

Color

Ivory

Dimension

Housing: 125 (Ø) x 74.5 (H) mm
Dome: 65(Ø) mm

Weight (Approx.)

455g (1lb)

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

29

3.6 Camera Dimensions

M o u nting tem pla te

 2.56 in. (65 mm)

1.35 in. (34.3 mm)
 4.92 in. (125 mm)

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

30

3.7 Compatible Accessory Installation (Mounts)

The following are the various combinations of the compatible accessories to mount this camera model.

Model Names & Combinations:

 VX-2AD-WM + VX-2AD-PMC
 VX-2AD-CM + VX-2AD-PMC
 VX-2AD-GB

Refer to the corresponding accessory model’s installation guide for the instructions.

Model Image

VX-2AD-WM

VX-2AD-CM

VX-2AD-PMC

VX-2AD-GB

3.7.1 WALL MOUNT- VX-2AD-WM

Contents

Installation

Steps:

1). Cover the wall mount bracket with the waterproof gasket like the image on the left.

M5 Tapping Screw x 4

Plastic Anchor x 4

Waterproof Gasket x 1

Wall Mount Bracket x 1

NPT 1-1/4”

Wall Mount Bracket

Waterproof Gasket

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

31

Drill the four holes on the installation surface based on the screw holes on the wall mount bracket, and
insert the plastic anchors into the holes. Then, insert the tapping screws through the screw holes on the
wall mount bracket into the anchor blocks to tighten the bracket into the wall

Attach an Additional Bracket

Attach an additional bracket at the bottom of VX-2AD-WM by referencing to the bracket’s installation
section, Pendant Mount Cap - VX-2AD-PMC.

Waterproof Gasket

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

32

3.7.2 CEILING MOUNT- VX-2AD-CM

Contents

Installation

Steps:

1). Cover the ceiling mount bracket with the waterproof gasket like the squared image on the left.

2). Drill the four holes on the installation surface based on the screw holes on the ceiling mount

bracket, and insert the plastic anchors into the holes. Then, insert the tapping screws through
the screw holes on the ceiling mount bracket into the anchor blocks to tighten the bracket into
the ceiling.

M5 Tapping Screw x 4

Plastic Anchor x 4

Ceiling Mount Bracket x 1

Waterproof Gasket x 1

Wall Mount

Waterproof

NPT 1-1/4”

Plastic Anchor

Ceiling Mount

Tapping Screw

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

33

Attach an Additional Bracket

3). Attach an additional pendant bracket at
the bottom of VX-2AD-CM by referencing
to the bracket’s installation section,

Pendant Mount Cap - VX-2AD-PMC.

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

34

3.7.3 PENDANT MOUNT CAP - VX-2AD-PMCB

Contents

Installation

Steps:

1). Install your camera at the bottom of VX-2AD-PMCB with the corresponding bolts by reference

to the screw hole below.

Screw Holes Guide for Camera

The image below shows the bottom of VX-2AD-CM with the screw holes specific to the VX-2AD3B-IWD
camera model (labelled as B). Refer to the screw hole information below to attach the VX-2AD3B-IWD
camera to the VX-2AD-CM mount.

(M4 x 22 bolt & O-Ring & Waterproof Bracket) x 2

(M4 x 12 bolt & O-Ring) x 4

VX-2AD-PMCB

A

A -A - A : IPN 32 0 2 H D
B - B : IP N 352H D & IP X55 0 2 H D
C - C : IP N 34 0 2H D
D - D - D : IP N 21 03H D & IP N 3102 H D & IPN 3 5 02H D

D

D

B

A C

B

A

C

D

B: VX-2AD3B-IWD

VX-2AD-CM

VX-2AD-PMCB

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

35

3.7.4 GANG BOX MOUNT – VX-2AD-GB

Contents

Installation

The images below show how to attach VX-2AD-GB to gang boxes of four different types.
Refer to the screw hole information to attach VX-2AD-GB to your gang box.

Single Gang Box

Double Gang Box

Octo Gang Box 1

Octo Gang Box 2

(M4 x 22 bolt & O-Ring & Waterproof Bracket) x 2

VX-2AD-GB

M4 x 20 bolt x 4

< VX-2AD-GB attached to a 3.5”octo gang box >

< VX-2AD-GB attached to a single gang box >

< VX-2AD-GB attached to a double gang box >

< VX-2AD-GB attached to a 70mm octo gang

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

36

A -A : IPN 35 2 H D & IPX 55 0 2 H D

A

A

B - B - B : IP N 3202H D
C - C -C : IP N 210 3H D & IPN 31 02H D & IP N 35 0 2 H D

BB

B

CC

C

D - D : IP N 3402H D

D D

Screw Holes Guide for Camera

The image below shows the bottom of VX-2AD-GB with the screw holes specific to the VX-2AD3B-IWD
camera model (labelled as A). Refer to the screw hole information below to attach the VX-2AD3B-IWD
camera to the VX-2AD-GB mount.

A: VX-2AD3B-IWD

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

37

4 VX-2A-IMD-X - 2 MP Interior Mini Dome Camera

The VX-2A-IMD-X is a fully functional indoor IP camera with advanced analytics capabilities. These
cameras can be connected to a DVR or act as a standalone recording device.

The interior mini dome offers high-definition video at full 1920 x 1080 resolution for indoor video
surveillance applications which require superior clarity and detail. Its many features include; dual­streaming of either H.264 or MJPEG compression; Micro SD card slot for local recording; and an
unobtrusive dome design.

The embedded analytics use algorithms that automatically self-adjust, allowing the user to concentrate
on the detection rules. This greatly simplifies the analytic process, requiring only a few mouse clicks to
configure a detection rule. These advanced analytics allow for object classification, direction, people
counting, dwell times, and occupancy counts.

When enabled, the embedded VIGIL Server software from 3xLOGIC allows the camera to be run as a
stand-alone device recording video to the onboard memory card. This makes the camera compatible
with the 3xLOGIC software suite including VIGIL Client, VIGIL VCM, VIGIL Mobile and VIGIL Cloud
applications. Simple plug and play installation allows for access using a standard web browser, VIGIL
Client, or your mobile device or tablet using our easy to use QR code quick setup.

4.1 VX-2A-IMD-X Specifications - Quick Summary

Component

Feature Description

Camera

 1/2.7” 1080p CMOS Image Sensor
 Digital Day/Night
 WDR
 Vandal Proof (IK09)

Video

 H.264 Baseline, Main, High profile (MPEG-4 Part 10/AVC), MJPEG (Motion

JPEG)

 Max 30fps in 1080p
 Text Overlay

Network

 10/100 Base-T Ethernet

Integration

 ONVIF compliant (Profile S)

General

 Micro SD/SDHC Card Slot x1
 Power over Ethernet (PoE)

Video Contents
Analysis (VCA)

 VCA Presence Standard

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

38

4.2 Package Contents

Please unpack the package carefully and handle the equipment with care.
The package contains:

Camera

Screws(M4x20) and anchor blocks

Quick Installation Guide

Torx Wrench(T-10)

White Plug

Installation Template

NOTE: The contents above are subject to change without prior notice.

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

39

4.3 Part Names

1). LAN connector: RJ45 LAN connector for 10/100 Base-T Ethernet (PoE supported).
Reset button: Use the button to restart the device or to reset it to Factory Default. Refer to the 3xLOGIC
VISIX All-in-One Camera User Manual for more details on restarting/resetting to factory default.
microSD/SDHC card slot: Supports up to 32GB. Recommend Class 4 and higher for HD recordings.

* Models herein and their appearance are subject to change without any prior notice.

❶

❷

❸

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

40

4.4 Installation

4.4.1 INSTALLING THE CAMERA – INSTALLING WITHOUT BRACKET

Installation Template

CAUTION: Installation template’s image size scale in this installation guide is not 1:1. The correct-size

template design paper can be found inside the package separately.

2 x .236 in. (6 mm)

3.35 in. (85 mm)

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

41

Steps:

1). Place the installation template included in the

package on the desired installation surface.

2). Drill two holes in the correct positions based

on the paper mounting template, insert the
plastic anchors into the holes, and tighten
them into the holes.

3). Loosen the two bolts on the dome cover with

the provided torx wrench (T-10) to open the
dome cover.

4). Connect necessary cables including a LAN cable

and a power cable to the camera.

5). Place the camera body to match the alignment

holes with the provided plastic anchors, and
hold the camera against the surface where the
camera will be mounted.

6). Tighten the plastic anchors with the provided

screws (M4x20).

7). Once you can see the video on the camera,

adjust the angle of the camera. Refer to
Adjusting Angle of the Camera for more details.

8). Place the dome cover on the camera's main

body to close the dome cover. Dome cover has
two alignment holes that match the camera
body’s alignment holes.

9). Once properly placed, tighten the bolts with

the provided torx wrench (T-10).

10). As the last step, insert the white plugs into the

screw holes on the dome to keep the dome
cover neatly.

CAUTION: To prevent products from damage, place the

camera on stable and non-vibrating surfaces If the
stability is in doubt, consult safety personnel for
reinforcements, and then proceed with the installation.

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

42

4.4.2 ADJUSTING ANGLE OF THE CAMERA

Adjust the angle of the camera by manually moving the corresponding parts following the directions
below.

4.5 Connections

1). LAN Connection: This is a RJ45 LAN connector for 10/100 Base-T Ethernet. Use the Ethernet cable

(RJ45. to connect the device to a hub or a router in the network. Refer to Section 7: Power over

Ethernet Specfications for further detail.

Connection Status Indicators: Two LEDs are located near the SD card slot, and you can check the
connecting status by observing the LED on the right side.

 Solid red – The device is in the process of booting.

 Blinking green – Booting is completed

B. To pan, rotate the lower
body of the camera gimbal.

C. Rotate the lens
with upper lens shell

A. To tilt, tilt the lens by vertically
adjusting the camera gimbal.

LAN Connection

❶

❷

Connection Status LEDs

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

43

4.6 Full Camera Specifications

Camera Module

CMOS

Image Sensor

1/2.7” 1080p CMOS

Effective Pixels

1920x1080

Scanning system

Progressive scanning

Electrical

Resolution

1920 x 1080

Min. Illumination

Color: 1.0Lux B/W : 0.001 Lux (DSS ON)

AGC Control

Auto

Lens

2.0mm, F2.0

Day & Night

Digital Day & Night

Wide Dynamic
Range

Digital WDR

Video

Compression
Format

H.264 Baseline, Main, High profile (MPEG-4 Part 10/ AVC),
MJPEG (Motion JPEG)

Number of
Streams

Dual Stream, Configurable streams in H.264, MJPEG
H.264: Controllable frame rate, bandwidth(VBR/CBR)
MJPEG: Controllable frame rate, JPEG quality

Resolution

1920x1080, 1280x720, 1120x630, 960x540, 800x450, 640x360, 480x270,
320x180

Compression FPS

30fps@1080p

Motion Detection

Built-in

Burnt-in Text
(Digital)

Video stream overlay text

Audio

Input/output

-

Compression
Format

-

Function

Digital
Input/Output

-

RS-485

-

Network

10/100 Base-T

Power over
Ethernet (PoE)

Supported

Protocol

QoS Layer 3 DiffServ, TCP/IP, UDP/IP, HTTP, HTTPS, FTP, RTSP, RTCP, RTP/UDP,
RTP/TCP, mDNS, UPnP™, SMTP, DHCP, DNS, DynDNS, NTP, SNMPv1/v2c/v3(MIB­II), IGMP, ICMP, SSLv2/v3, TLSv1

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

44

Function

SD Slot

1 x microSD memory card slot
(SD/SDHC up to 32 GB supported)
※ Card not included
(Class 4 and higher recommended for HD recordings)

Electrical Characteristics

Power Source

PoE IEEE802.3af (Class 2)

Power
Consumption

2.4W @ PoE

Video Output

-

Audio Input

-

Audio Output

-

D/I - D/O

-

Environment Condition

Operating
Temperature

Operating Range
PoE : 0 ˚C ~ 40 ˚C (32˚F ~ 104˚F)

Operating
Humidity

Up to 85% RH

Mechanical Condition

Material

Aluminum Die-Casting (Vandal Resistance)

Color

Ivory

Dimension

Housing: 105.5 (Ø) x 55.5(H) mm
Dome : 27.5(Ø) mm

Weight (Approx.)

270g (0.6lb)

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

45

4.7 Camera Dimensions

R 1.08 in.
(27.5 mm)

R 2.19 in. (55.5 mm)

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

46

4.8 Compatible Accessory Installation (Mounts)

The compatible accessories to mount this camera model are as follows.

Model Names & Combinations

 VX-2AIMD-CM
 VX-2AIMD-WM
 VX-2AIMD-CM + VX-2AIMD-PMC
 VX-2AIMD-GB

The installation instructions for each bracket are contained within the proceeding sections of this manual.

Model Image

VX-2AIMD-CM

VX-2AIMD-CM

VX-2AIMD-PMC

VX-2AIDM-GB

4.8.1 WALL MOUNT - VX-2AIMD-WM

Contents

Wall Mount Bracket

Tapping Screw 3ea

Plastic Anchor 3ea

M3x6L BOLT 4ea

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

47

Installation

Steps:

1). Drill three small holes for plastic anchor and one hole for cabling work on the ceiling based on

the holes of the bracket. Refer to Location of the Holes for M3x6L Bolts on the next page to
identify the holes information.

2). Insert the plastic anchors (3ea) to the drilled three holes.

3). Fix the bracket on the wall by tightening the tapping screws (3ea) into the plastic anchors.

4). Detach the dome cover from the camera by loosening the bolts with the hex wrench included

in the camera package.

5). Fix the camera at the bottom of the bracket with the M3x6L bolts. Ensure that the necessary

cables are properly connected to the camera.

6). For the last parts of the installation, refer to the steps 7 to 10 in Section 4.4: Installing the

Camera - Installation without Bracket of this manual.

Tapping Screw

Wall Mounting Bracket

Plastic Anchor

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

48

4.8.2 LOCATION OF THE HOLES FOR M3X6L BOLTS

The image below shows which spots the camera should be attached to on the wall mount bracket (VX­2AIMD-CM).

1). Identify the location of the holes with the alphabet letter, B, on the bracket, and insert the

M3x6L bolts in the holes to attach the camera.

A -A - A (M 3T A P )

A

B

B

A

A

IP N 32 02H D

B - B (M 3T A P )

IP N 30 2H D

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

49

4.8.3 CEILING MOUNT - VX-2AD-CM

Contents

Installation

Steps:

1). Drill three holes for the plastic anchors based on the installation template as well as the hole

for the cable dropped from the ceiling. Then, route the LAN cable through the bracket’s pipe.

Ceiling Mount Bracket
Tapping Screw 3ea

Plastic Anchor 3ea

Installation Template 1ea

Ceiling Mount Bracket

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

50

2). Insert the three anchor blocks into the holes on the ceiling.

3). Fix the bracket to the ceiling by inserting the tapping screws into the anchor blocks and

tightening them for the firm attachment.

4). This ceiling mount bracket normally requires a pendant mount cap to attach the camera. Refer

to the installation method in Pendant Mount Cap on the next page.

Plastic Anchor

Tapping Screw

Ceiling Mount Bracket

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

51

4.8.4 PENDANT MOUNT CAP - VX-2AD-PMC

Contents

Installation

Steps:

1). Rotate the pendant mount cap counterclockwise on the thread at the bottom of the ceiling

mount bracket, and tighten the set screw (installed on the pendant mount cap) with the hex
wrench included in the bracket package for the firm attachment of the pendant mount cap.

Pendant Mount Cap

M5x6L Hex Socket Set Screw 1EA

(pre-installed)

M4x8L Hex Wrench Bolt 2EA

2.5mm Hex Wrench 1EA

Hex Wrench

Ceiling Mount Bracket

(Model No: VX-2AD-PMC)

Pendant Mount Cap

Set Screw

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

52

5). Connect your LAN (or PoE) cable from the ceiling pipe to the LAN connector on the camera,

and insert the camera into the pendant mount cap. Then, fix the camera to the pendant
mount cap by inserting the bolts (M4x8L) to the alignment holes on the pendant mount cap
and tightening them with the hex wrench included in the camera package.

6). For the last part of the installation, refer to steps 7 to 10 in Section 4.4: Installing the Camera

– Installation without Bracket in this manual.

Hex Wrench

M4x8L Hex Wrench Bolt

Biscuit Camera

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

53

5 VX-VT-20, VX-VT-36, VX-VT-58 – VERA 20°, 36°,

58° Thermal Bullet Camera

The VERA indoor/outdoor thermal bullet gives you the advantage to see where you couldn’t before.
When using high-contrast thermal imaging the results are a dramatic reduction in false alarms. Our
thermal camera stands out from the pack with verification and detection in an all-in-one device. Easy
setup and integration using our QR code makes this a perfect camera for any application.
The exterior thermal camera is not affected by changes in lighting, low contrast scenes or inclement
weather. There is no illumination required.
The VERA Thermal line includes three models with a 20, 36 or 58 degree field of vision. The VERA
camera’s embedded analytics use algorithms that automatically self-adjust, allowing the user to
concentrate on the detection rules. This greatly simplifies the analytic process, requiring only a few
mouse clicks to configure a detection rule. These advanced analytics, coupled with thermal technology
allow for object classification, direction, people counting, dwell times, video alarm verification, retail
traffic flow, queue management and occupancy counts.
When enabled, the embedded VIGIL Server software from 3xLOGIC allows the camera to be run as a
stand-alone device recording video to the onboard memory card. This makes the camera compatible
with the 3xLOGIC software suite including VIGIL Client, VIGIL VCM, VIGIL Mobile and VIGIL Cloud
applications. Simple plug-and-play installation allows for access using a standard web browser, VIGIL
Client, or your mobile device or tablet using our easy to use QR code quick setup.

5.1 VX-VT-20, VX-VT-36, VX-VT-58 Specifications – Quick

Summary

Component

Feature Description

Camera

 17 ㎛ vanadium oxide microbolometer technology
 206x156 array size / various resolutions via scale-up
 20, 36 or 50 degree field-of-view (depending on model)

Streaming

 Dual streaming supported
 Burnt-in text (OSD) supported
 Unicast/Multicast supported

Video

 H.264 and MJPEG(Motion JPEG)
 Max 9fps in all resolutions
 Text Overlay
 Video Motion Detection Supported

Audio

 Two-way audio streaming
 Audio compression: G.711 µLaw

Sensor/Alarm

 1 Digital Input / 2 Digital Outputs

Network

 RTSP/HTTP Protocols supported
 10/100 Base-T Ethernet

Integration

 ONVIF compliant (Profile S)

General

 Micro SD/SDHC Card Embedded
 Power over Ethernet (PoE)

Video Contents
Analysis (VCA)

 VCA Presence Standard

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

54

5.2 Package Contents

Please unpack the package carefully and handle the equipment with care. The package contains:

NOTE: The contents above are subject to change without prior notice.

Camera

DC Power Adaptor & Universal Plugs

Screws (M4x30) & Plastic Anchors

Wall Cushion

Torx Wrench (T20 M4x23)

Quick Start Guide

Ferrite Core

Installation Template

Torx Wrench

Screw &
Plastic Anchor-3pcs

Quick Installation Guide

Installation Template

WALL CUSHION

Torx Wrench

Screw &
Plastic Anchor-3pcs

Screw &
Plastic Anchor-3pcs

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

55

5.3 Part Names

1). Sunshield: It prevents direct sunlight.

2). Audio|Sensor|Alarm connection cables: Cables to connect audio input(microphone), audio

output(speaker), digital input(sensor), and digital output(alarm). Refer to Section 5.5: Connections
for more information.

3). LAN connector: RJ45 LAN connector for 10/100 Base-T Ethernet (PoE supported).

4). Power adaptor connector: Connect the provided DC12V adaptor for power supply.

BLACK
BROWN
RED
ORANGE
YELLOW
GREEN
BLUE
VIOLET
GRAY

AUD IN
AUD GND
AUD OUT
DI
DI COM
DO1(N.O)
DO1 COM
DO2(N.C)
DO2 COM

 Audio|Sensor|Alarm

connection cables

LAN connector

 Sunshield

Power adaptor

connector

❶

❷

❸

❹

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

56

5.4 Installation

5.4.1 INSTALLING THE CAMERA – INSTALLATION WITHOUT BRACKET

Installation Template

CAUTION: Installation template’s image size scale in this installation guide is not 1:1. The correct-size

template paper can be found inside the package separately.

Ø2.72 in. (69 mm)

3 - Ø0.26 in. (6.5 mm)

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

57

Steps:

1). Drill three holes on the installation surface based on the provided installation template.

2). Insert the plastic anchors into the holes.

3). Install the provided ferrite core on the cable by referring to the NOTE: below.

4). Attach the provided wall cushion to the bottom of the camera’s pan/tilt bracket.

5). Fix the camera to the installation surface.
a. Align the screw holes of the camera’s pan/tilt bracket and the plastic anchors.

b. Insert the provided screws(M4X35) into the plastic anchors through the screw holes of the

camera’s pan/tilt bracket.

c. Tighten the screws firmly into the plastic anchors.

6). Connect all the necessary cables by referring to Section 5.5: Connections for more

information.

7). Adjust the angle by referring to Adjust Angle of the Camera.

NOTE: Installing the ferrite core to a LAN cable is highly recommended to reduce high frequency noise

level. Please follow the instructions below:

Steps:

1). Open the ferrite core by lifting the clip.

2). Make one loop with the cable through the ferrite core.

3). Close the ferrite core to hold the cable loop into its place.

CAUTION: Sealing gaps is recommended as gaps may appear after the camera installation. Gaps may

cause problems such as moisture, water leakage and etc., which negatively affect the operation of the
camera if gaps remain unsealed.

CAUTION: To prevent products from damage, place the camera on a stable and non-vibrating surface. If

the stability is in doubt, consult safety personnel for reinforcements, and then proceed with the
installation.

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

58

5.4.2 ADJUSTING ANGLE OF THE CAMERA

Steps:

1). Loosen the set screw located on the right side of the camera’s bracket by using the provided

Torx (T20 M4x23) wrench. Once the set screw is loosened, you can move the tilting joint and
the panning joint of the camera respectively.

2). Adjust the angle by moving the tilting joint and the panning joint.

❷

❶

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

59

5.5 Connections

1). Audio connection: The camera provides a mono audio input and output. Due to low audio output

power, an amplified speaker is recommended for enhanced sound (Refrain from connecting a
headphone or an earphone directly to the camera).

 Microphone In: Max 2Vp-p, 20KΩ (90dB)
 Headphone Out: 60mW, 16Ω (95dB)

2). Sensor (DI) connection: Sensor (DI) can be connected to either a voltage type sensor or a relay type

sensor as the following figures. Settings can be done through the camera’s webpage.

 Input voltage range: 0VDC minimum to 5VDC maximum, Max 50mA

CAUTION: Do not exceed the maximum input voltage or relay rate.

BLACK
BROWN
RED

AUD IN
AUD GND
AUD OUT

ORANGE
YELLOW

DI
DI COM

GREEN
BLUE
VILOET
GRAY

DO1(N.O)
DO1 COM
DO2(N.C)
DO2 COM

❹LAN connector

❺ Power adaptor

❶AUDIO

❷SENSOR

ALARM 1
ALARM 2

❸

Mic

Amp Speaker

ETHERNET

MICRO SD

DC12V

OutOut

In

AUDIO

+

Reset

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

60

3). Alarm (DO1 | DO2) connection: Only the relay type is supported.

 Digital Output 1
 Relay Rating: Max 30VDC 1A
 Normally Open (N.O) at power off
 Digital Output 2
 Relay Rating: Max 30VDC 1A
 Normally Closed (N.C) at power off

CAUTION: Do not exceed the maximum relay rating.

4). LAN connection: This is a RJ45 LAN connector for 10/100 Base-T Ethernet. Use the Ethernet cable

(RJ45) to connect the device to a hub or a router in the network. Refer to Section 7: Power over

Ethernet Specifications for more information.

5). Power Connection: The camera can be powered by either 12VDC or PoE. If the camera is powered

via PoE, you do not need to connect the power adaptor. For more information about PoE, refer to

Section 7: Power over Ethernet Specifications for more information.

NOTES:

 Temperature criterion for the heater operation: 0˚C (32˚F)
 Lowest temperature to

guarantee the heater operation during the device operation: -40˚C (-40˚F)

 Lowest temperature to boot up the device when the device is powered on:
 0˚C (32˚F)

+3.3V

DI

COM

DI

COM + -

Relay Type

Voltage Type

+

-

Output of
Sensor

Output of
Sensor

Internal

Internal

+

-

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

61

5.6 Full Camera Specifications

Camera Module

Array Size

206x156

Detection Type

Uncooled vanadium oxide microbolometer

Sensor pixel size

12um

Spectral Response

7.8 ~ 14

Lens

4mm, F1.2 (FOV:36o), 6.8mm F1.2(FOV:20 o), N/A FOV:58 o),

Sensitivity

Less than 100mK

Video

Compression Format

H.264 and MJPEG Selectable per Stream

Number of Streams

Dual Stream, Configurable

Resolution

4:3 Mode

QVGA(320x240), VGA(640x480), NTSC(720x480), PAL(720x576), SVGA(800x600)

16:9 Mode

320x180, 480x270, 640x360, 800x450, 960x540, 1120x630, 1280x720

Frame Rate

Max. 9FPS in all resolutions

Motion Detection

Built-in

Burnt-in Text (Digital)

Time stamp and text caption overlay

Analogue Output

-

Audio

Input/output

1/1 channel

Compression Format

G.711

Function

Digital Input/output

1/2 channel

RS-485

-

Network

10/100 Base-T

Power over Ethernet
(PoE)

Supported

Protocol

QoS Layer 3 DiffServ, TCP/IP, UDP/IP, HTTP, HTTPS, RTSP, RTCP, RTP/UDP,
RTP/TCP, mDNS, UPnP™, SMTP, DHCP, DNS, DynDNS, NTP, SNMPv2c/v3(MIB-II),
IGMP, ICMP, SSLv2/v3, TLSv1, SRTP, RTMP

Storage

1 x microSDHC card embedded

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

62

5.7 Camera Dimensions

2.40 in. (61 mm)

8.17 in. (207.5 mm)

2.99 in. (76 mm)

7.5 in. (190.5 mm)

6.75 in. (171.5 mm)

3.15 in.

(80 mm)

2.28 in.
(58 mm)

2.72 in.
(69 mm)

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

63

6 VX-2V28-PIN – IP Pinhole Camera

6.1 VX-2V28-PIN Specifications — Quick Summary

Component

Feature Description

Camera

 1/3” 1080p CMOS Image Sensor
 Digital Day/Night
 WDR

Video

 H.264 Baseline, Main, High profile (MPEG-4 Part 10/AVC), MJPEG (Motion

JPEG)

 Max 30fps in 1080p
 Text Overlay

Network

 10/100 Base-T Ethernet

Integration

 Software Development Kit (SDK) available
 ONVIF Compliant (Profile S & Profile G)

NOTE: ONVIF Profile G is supported from FW V1.8.0 or higher.

General

 Micro SD/SDHC Card Embedded
 Power over Ethernet (PoE)

Video Contents
Analysis (VCA)

 VCA Presence Standard

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

64

6.2 Package Contents

Please unpack the package carefully and handle the equipment with care. The package contains:

Camera Unit

Main Unit

Universal Plugs

Power Adaptor (DC12V)

Double-Sided Tape for
Pinhole Cover

Pinhole Cover

Rotate Ring

Surface Mount Bracket

Pan/Tilt Bracket

Tapping Screw
(TP1 M3x20) x 2EA

Screw
(TP2 M3x6(Ni)) x
2EA

Anchor Block
(M4x25) x 5EA)

Tapping Screw
TS1 (M4x25) x 5EA

Cable Clamp x 3EA

Ferrite Core

Tapping Screw
(TP1 M4x20) x 3EA

4 Pin Terminal Block

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

65

6.3 Part Names

6.3.1 MAIN UNIT:

1). Terminal Connector: Connector for cable connection for digital input / output. Refer to Section 6.5:

Cable Connection for more details.

2). Camera Connector: Connector for camera unit

3). microSD/SDHC card slot: The camera supports up to 32GB. Class 4 and higher SD card is

recommended for HD recordings.

4). Reset button: This button will restart or reset to factory default settings.

5). LAN Connector: RJ45 LAN connector for 10/100 Base-T Ethernet (PoE supported)

6). Power Adaptor Connector: DC 12V power supply connection

7). Slide Plate: Built-in mounting bracket for main unit

* Model herein and its appearance are subject to change without any prior notice.

❸

❶

❷

❺

❼

❹

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

66

6.3.2 CAMERA UNIT WITH CONJOINED ACCESSORIES

1). Camera

2). Camera DIN connector: Connector to be inserted to the camera connector in the main unit

3). Pinhole Cover: Bracket to be installed behind a wall or ceiling to hold the camera inside

4). Surface Mount Bracket: Bracket to be installed on a wall or ceiling to hold the camera inside

5). Pan/Tilt Bracket: Bracket to be installed on a wall or ceiling for the camera’s angle adjustment. It

shall be combined with the rotate ring and the surface mount bracket for the complete installation.

❶

❸

❹

❷

* Model herein and its appearance are subject to change without any prior notice.

❺

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

67

6.4 Installation

6.4.1 CAMERA UNIT INSTALLATION

There are three different ways to install the camera unit:

 Inconspicuously behind the wall or ceiling by using the pinhole cover
 Mounted and fixed on the wall or ceiling by using the surface mount bracket
 Mounted and fixed on the wall or ceiling by using the pan/tilt bracket to enable the

camera’s angle adjustment

6.4.2 INCONSPICUOUS INSTALLATION

Steps:

1). Drill a hole (diameter: 3mm) on a desired spot where the camera lens will be located.

2). Peel off one side of the double-sided tape, and attach it to the flat surface of the pinhole cover

by aligning the grooves on the tape with the screw holes on the pinhole cover.

3). Peel off the other side of the tape, and stick the

taped surface to the installation surface after
aligning the hole on the pinhole cover with the
drilled hole on the installation surface and facing
the top screw hole upward.

4). Fasten the pinhole cover by using the tapping

screws (M3x20) appropriate for the material of
the installation surface.

5). Place the camera inside the pinhole cover by

routing the camera’s cable through the cable
holder on the pinhole cover, and tighten the top
screw head to fix the camera.

tape

groove

Screw hole

(Behind the wall or
above the ceiling)

Screw head
cable holder

(Behind the wall or
above the ceiling)

cable holder

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

68

6). Use the cable clamp optionally if you want to fix the

camera’s cable to a desired spot with a tapping screw
(M4x20).

cable clamp

(Behind the wall or
above the ceiling)

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

69

6.4.4 SURFACE INSTALLATION FOR FIXED

ANGLE

Steps:

1). Place the camera on a desired installation surface.

2). Cover the camera with the surface mount

bracket by routing the camera’s cable into the
cable holder on the bracket. Then, fasten the
bracket using the tapping screws (M3x20) and
anchor blocks appropriate for the material of the
installation surface.

3). Use the cable clamp optionally if you want to fix

the camera’s cable to a desired spot with a
tapping screw (M4x20).

cable clamp

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

70

6.4.5 SURFACE INSTALLATION FOR PAN/TILIT

ADJUSTMENT

Steps:

1). Drill a hole on a desired installation surface, and insert

an anchor block into the hole.

2). Fix the pan/tilt bracket by inserting the tapping screw

(M4x25) to be passed through the screw hole on the
bracket and tightening it into the anchor block.

3). Insert the rotate ring into the bracket by pressing it

into the bracket’s mount ring

4). Place the camera unit on the pan/tilt bracket.

5). Place the surface mount bracket on top of the

camera, fix the bracket by inserting the tapping
screws (M3x6) into the screw holes on the bracket by
aligning the screw holes with the holes on the rotate
ring on the pan/tilt bracket, and tighten the screws

6). Use the cable clamp optionally if you want to fix the

camera’s cable to a desired spot with a tapping screw
(M4x20).

mount ring

rotate ring

cable clamp

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

71

6.4.6 MAIN UNIT INSTALLATION

The main unit can be mounted on the installation surface by the built-in slide plates.

Steps:

1). Pull out both slide plates at the bottom of the main

unit.

2). Place the main unit on the installation surface by

facing the bottom of the main unit toward the
installation surface, and mark the drilling spots based
on the alignment holes on the slide plates.

3). Drill the marked spots with a screw driver.

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

72

4). Insert the anchor blocks to the drilled holes, and

tighten them into the installation surface.

5). Place the main unit in the same way as in Step 2 and

insert the tapping screws to be passed through the
alignment holes on the main unit.

6). Tighten the screws into the anchor blocks to fix the

main unit to the installation surface.

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

73

6.5 Cable Connection

6.5.1 DI/DO TERMINAL CONNECTOR

1). Connect external input/output devices (e.g. alarm device) optionally if they are necessary. Refer to

the reference below for the appropriate connection.

 DO (Alarm): It is used for connecting an external device such as relays and LEDs.

Refer to the table below for electrical wiring information:

DO

Function

Specifications

C

Ground

1

Output

0 to 24 VDC
Max load: 50mA

Then, the connected device can be activated via its webpage.

C 1 C

1

DO

DI

❶

❷

❸

❹

DO

COM

Relay Type

Device

Internal

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

74

 DI Sensor: It is used for connecting a device such as a PIR and a door/window sensor.

Refer to the table below for electrical wiring information:

DO

Function

Specifications

C

Ground

1

Input

0 to 5 VDC
Max load: 50mA

Then, the connected device can be activated via its webpage.

6.5.2 CAMERA CONNECTOR

2). Connect the camera unit to the main unit by inserting the camera’s DIN connector to the camera’s

connector on the main unit by placing the arrow mark to be shown upward like the image below.

NOTE: Please make sure that the camera unit needs to be connected to the main unit prior to the

power connection. Otherwise, the camera may fail to show image.

+3.3V

DI

COM

DI

COM + -

Relay Type

Voltage Type

+

-

Output of
Sensor

Output of
Sensor

Internal

Internal

+

-

C 1 C

1

D

DI

❶

❸

❹

❷ ❷

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

75

6.5.3 LAN CONNECTOR

3). Connect the main unit to the network using an Ethernet cable (RJ45). Then, install the ferrite core

on the Ethernet cable. Refer to the explanations below for the ferrite core installation.

NOTE: In case you intend to turn on the device by using the LAN cable, a PoE switch should be

available in your network. For more information about PoE, refer to Section 7: Power over Ethernet

Specifications for more information.

NOTE: Installing the provided ferrite core is highly recommended to reduce high frequency electrical noise

level. Here below are the instructions to install the ferrite core on the Ethernet cable.

Steps:

1). Open the ferrite core by lifting the clip.

2). Make one loop with the cable through the ferrite core. (See the enlarged image above.)

Close the ferrite core to hold the cable loop in the ferrite core’s chamber.

6.5.4 POWER CONNECTOR

4). Connect a DC12V power adaptor to the power connector on the main unit. If the camera is

powered on via PoE, a power adaptor is not necessary to be connected to the main unit.

NOTE: Please make sure that the camera unit needs to be connected to the main unit prior to the

power connection. Otherwise, the camera may fail to show image.

❸

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

76

6.6 Camera Dimensions

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

77

6.7 Full Camera Specifications

Camera Module

CMOS

Image Sensor

1/3” 1080p CMOS

Effective Pixels

1920x1080

Scanning system

Progressive scanning

Electrical

Resolution

1920 x 1080

Min. Illumination

Color: 1.4 Lux / B/W : 0.01 Lux (DSS ON)

AGC Control

Auto

Lens

2.8mm, F2.4

Day & Night

Digital Day & Night

Wide Dynamic
Range

Digital WDR

Video

Compression
Format

H.264 Baseline, Main, High profile (MPEG-4 Part 10/ AVC), MJPEG (Motion JPEG)

Number of
Streams

Dual Stream, Configurable streams in H.264, MJPEG
H.264: Controllable frame rate, bandwidth(VBR/CBR)
MJPEG: Controllable frame rate, JPEG quality

Resolution

1920x1080, 1280x720, 1120x630, 960x540, 800x450, 640x360, 480x270,
320x180

Compression FPS

30fps@1080p

Motion Detection

Built-in

Burnt-in Text
(Digital)

Video stream overlay text

Audio

Input/output

-

Compression
Format

-

Function

Digital
Input/Output

1/1 channel

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

78

Function

RS-485

-

Network

10/100 Base-T

Power over
Ethernet (PoE)

Supported

Protocol

QoS Layer 3 DiffServ, TCP/IP, UDP/IP, HTTP, HTTPS, FTP, RTSP, RTCP, RTP/UDP,
RTP/TCP, mDNS, UPnP™, SMTP, DHCP, DNS, DynDNS, NTP, SNMPv1/v2c/v3(MIB­II), IGMP, ICMP, SSLv2/v3, TLSv1, SRTP, RTMP

SD Slot

1 x microSD memory card slot
(SD/SDHC up to 32 GB supported)
※ Card not included
(Class 4 and higher recommended for HD recordings)

Electrical Characteristics

Power Source

DC 12V (Class 2, LPS) / PoE IEEE802.3af (Class 0)

Power
Consumption

6W @ DC12V

Video Output

-

Audio Input

-

Audio Output

-

D/I

Max 50mA@5VDC, TTL level 1.5V threshold

D/O

Max 50mA@24VDC
On-state resistance:50 Ω (max continuous)

Environment Condition

Operating
Temperature

Operating Range
[DC12V] [PoE]: -10 ˚C ~ 50 ˚C (14˚F ~ 122˚F)

Operating
Humidity

Up to 85% RH

Mechanical Condition

Material

Polycarbonate

Color

Main Unit: White
Camera Unit: Black

Dimension

28.1(Ø) x 25 mm

Weight (Approx.)

Main Unit: 225g (0.50lbs)
Camera Unit: 250g (0.55lbs)

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

79

7 Power over Ethernet Specifications

The Power over Ethernet (PoE) is designed to extract power from a conventional twisted pair Category 5
Ethernet cable, conforming to the IEEE 802.3af Power-over-Ethernet (PoE) standard.

IEEE 802.3af allows for two power options for Category 5 cables.
The IEEE 802.3af-2003 standard allows up to 15.4 W of power the device. However, 12.95W is the

available power, as some power gets lost in the cable. The updated IEEE 802.3at-2009 (PoE+) standard
allows up to 25.5 W (Max 34.2 W) of power the device.

PoE has advantages over conventional power in such places where AC powers cannot be reached or is
expensive to wire.

7.1 Power Comparison

Property

802.3af

802.3at

Available Power

12.95 W

25.50 W

Max. Power by PSE

15.40 W

34.20 W

Max. Current

350 mA

600 mA

Supported Cable

Category 3 or higher

Category 5 or higher

NOTE: For proper activation of PoE, the Category 5 cable must be shorter than 100m and conform the

PoE standard.

NOTE: When it is connected with non PSE, the power adaptor should be connected.
NOTE: Connecting both PSE and power adaptor does not do any harm to the product. Disconnecting PSE

or power adaptor from device does not reboot the device as long as either one is connected to the
device.

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

80

8 Revision History

Man #

Date (mm/dd/yyyy)

Comments

11-2015-1

11/19/2015

Styled

01-2016-22

01/22/2016

Finalized first draft

11-2017-10

11/10/2017

Revised for VIGIL v10

-Added VX-VT-58, VX-2A-B-RIWD

06-2018-20

06/20/2018

Added VX-2A-B-RIWDZ

07-2018-31

07/31/2018

Added VX-2AD3B-IWD