3M B2194981 User Manual
3M™ Scotch-Brite™ Products, HS Blend and Finish A MED 03/14/14
__________________________________________________________________________________________
Page 1 of 9
Safety Data Sheet
Copyright,2014,3M Company.
All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is
allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from
3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.
Document Group:
24-1167-6
Version Number:
2.03
Issue Date:
03/14/14
Supercedes Date:
03/22/13
SECTION 1: Identification
1.1. Product identifier
3M™ Scotch-Brite™ Products, HS Blend and Finish A MED
1.2. Recommended use and restrictions on use
Recommended use
Abrasive Product
1.3. Supplier’s details
MANUFACTURER:
3M
DIVISION:
Abrasive Systems Division
ADDRESS:
3M Center, St. Paul, MN 55144-1000, USA
Telephone:
1-888-3M HELPS (1-888-364-3577)
1.4. Emergency telephone number
1-800-364-3577 or (651) 737-6501 (24 hours)
SECTION 2: Hazard identification
2.1. Hazard classification
Not classified as hazardous according to OSHA Hazard Communication Standard, 29 CFR 1910.1200.
2.2. Label elements
Signal word
Not applicable.
Symbols
Not applicable.
Pictograms
Not applicable.
Notes to Physician:
Not applicable
2.3. Hazards not otherwise classified
None.
3M™ Scotch-Brite™ Products, HS Blend and Finish A MED 03/14/14
__________________________________________________________________________________________
Page 2 of 9
71% of the mixture consists of ingredients of unknown acute oral toxicity.
SECTION 3: Composition/information on ingredients
Ingredient C.A.S. No. % by Wt
Aluminum Oxide Mineral (non-fibrous) 1344-28-1 25 - 45
Lubricant 4485-12-5 1 - 3
Titanium Dioxide 13463-67-7 0.5 - 1.5
Cured Resin Mixture 30 - 50
Nylon Fiber 32131-17-2 10 - 25
Roloc Attachment Mixture 0 - 3
Loop Backing Mixture 0 - 10
SECTION 4: First aid measures
4.1. Description of first aid measures
Inhalation:
Remove person to fresh air. If you feel unwell, get medical attention.
Skin Contact:
Wash with soap and water. If signs/symptoms develop, get medical attention.
Eye Contact:
Flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. If signs/symptoms persist, get
medical attention.
If Swallowed:
No need for first aid is anticipated.
4.2. Most important symptoms and effects, both acute and delayed
See Section 11.1. Information on toxicological effects.
4.3. Indication of any immediate medical attention and special treatment required
Not applicable
SECTION 5: Fire-fighting measures
5.1. Suitable extinguishing media
In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam to extinguish.
5.2. Special hazards arising from the substance or mixture
None inherent in this product.
Hazardous Decomposition or By-Products
Substance Condition
Carbon monoxide During Combustion
Carbon dioxide During Combustion
5.3. Special protective actions for fire-fighters
No unusual fire or explosion hazards are anticipated.
3M™ Scotch-Brite™ Products, HS Blend and Finish A MED 03/14/14
__________________________________________________________________________________________
Page 3 of 9
SECTION 6: Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
Observe precautions from other sections.
6.2. Environmental precautions
Not applicable.
6.3. Methods and material for containment and cleaning up
Not applicable.
SECTION 7: Handling and storage
7.1. Precautions for safe handling
For industrial or professional use only. Avoid breathing of dust created by sanding, grinding or machining. Damaged
product can break apart during use and cause serious injury to face or eyes. Check product for damage such as cracks or nicks
prior to use. Replace if damaged. Always wear eye and face protection when working at sanding or grinding operations or
when near such operations. Combustible dust may form by action of this product on another material (substrate). Dust
generated from the substrate during use of this product may be explosive if in sufficient concentration with an ignition source.
Dust deposits should not be allowed to accumulate on surfaces because of the potential for secondary explosions.
7.2. Conditions for safe storage including any incompatibilities
No special storage requirements.
SECTION 8: Exposure controls/personal protection
8.1. Control parameters
Occupational exposure limits
Ingredient C.A.S. No. Agency Limit type Additional Comments
Aluminum Oxide Mineral (non-
fibrous)
1344-28-1 Chemical
Manufacturer
Rec Guid
TWA:1 fiber/cc
Aluminum Oxide Mineral (non-
fibrous)
1344-28-1 US Dept of
Labor - OSHA
TWA(as total dust):15
mg/m3;TWA(respirable
fraction):5 mg/m3
Aluminum, insoluble compounds 1344-28-1 Amer Conf of
Gov. Indust.
Hyg.
TWA(respirable fraction):1
mg/m3
Titanium Dioxide 13463-67-7 Amer Conf of
Gov. Indust.
Hyg.
TWA:10 mg/m3
Titanium Dioxide 13463-67-7 Chemical
Manufacturer
Rec Guid
TWA(as respirable dust):5
mg/m3
Titanium Dioxide 13463-67-7 US Dept of
Labor - OSHA
TWA(as total dust):15 mg/m3
Nylon Fiber 32131-17-2 Chemical
Manufacturer
Rec Guid
TWA(as respirable dust):5
mg/m3;TWA(as total dust):10
mg/m3
STEARATES 4485-12-5 Amer Conf of
Gov. Indust.
Hyg.
TWA:10 mg/m3
Loading...